Waste Small Engine Float Bowl Gasket Parts

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more

Burners were an exact match for the originals and the pans fit perfectly. Vastly improved the appearance of an old cook top and allowed us to to not have to replace it before our home goes up for sale. Read more

The right door seal and the freezer door seal are easily removed and replaced. They just pull out of the slot. These 2 new gaskets push in easily. The left door has the French Door Mullion, that blocks the removal of the door gasket. There are two screws in the middle that holds it on, and there is a spring at the bottom of the mullion that keeps the mullion in place. The spring can easily be removed, or left in place. There is an electrical connector in the middle of the mullion. As suggested... Read more

Checked out You tube video. Easy tune up. One gasket was damaged and I did not notice that the brush holders has no brushes. I believe a quick call to Appliance parts pros will fix this, besides I need a few more parts. I expect to get another 20+ years from this KitchenAide mixer, once repairs are competed. Watch out for the single lock washer located on the rear upper housing screw, you don't want to lose this! Read more

Initially did a uTube search for specific instructions on dismantling this machine for this repair. I had successfully replaced a door/tub gasket on a Whirlpool front load machine previously. Did not find specific uTube instructions for this Kenmore. So began removing parts using past learned info on what needed to be removed first, second, and last. Removed the top, detergent dispenser screws/control panel, then the front (with a couple hidden screws around drain pump filter) and the front... Read more

• Will not fill with water

Cycle would complete but dishes weren't clean (not even really wet) and soap wasn't dissolving. Could hear fill at start but maybe not spraying or filling again in cycle. Thought it was the control board, but actually this was not the error. Replaced the control board and same problem arose, only new control board version actually stopped cycle with message that dishwasher couldn't fill. Looking underneath the pump had somehow become dislodged from the bottom of dishwasher and was laying on... Read more

Ordered New Gasket and installed in about 3-4 Minutes. Only need small pliers to remove some of old clips from holes. New Gasket clipped in easily by hand. Read more

LG Washing Machine WM3885HCCA I searched the Appliance Parts Pros "Get Repair Help" tab, typed in the LG washing machine model number (WM3885HCCA), watched videos and searched for the parts shown on the diagrams of my LG washing machine. After finding parts, I confirmed on both the Appliance Parts Pros site and LG site that the parts I selected were correct. I highly recommend using the LG site . I was able to type in the original part number from the Appliance Parts Pro site and LG directed... Read more

Removed water out of basin, down to the last inch.. Watched water rise slowly, and felt temperature, warm. This told me it was supply water. Ordered replacement part, two days just as mentioned, Removed as per video. Also choose to replace the waste line check valve, to affordable not too. Working great, except the wood floor not so happy with. One thing at a time. Thanks Read more

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

All parts arrived in one box - I purchased the tub gasket, lower door gasket and lower door seal. My existing parts were visibly pretty worn out, dishwasher is 12 years old (maybe should have just bought anew one?). Tub gasket was pretty easy, it took me a while to make sure it was even all the way around, after attest run and the subsequent drying heat it fits nicely. Lower door seal went as video, all good, my other one was destroyed from the heat cycles. Could not get the lower door seal... Read more

The right door seal and the freezer door seal are easily removed and replaced. They just pull out of the slot. These 2 new gaskets push in easily. The left door has the French Door Mullion, that blocks the removal of the door gasket. There are two screws in the middle that holds it on, and there is a spring at the bottom of the mullion that keeps the mullion in place. The spring can easily be removed, or left in place. There is an electrical connector in the middle of the mullion. As suggested... Read more

• Leaks water

Noticed large banging in the washing machine when transitioning from low to high speed spin. Also would get a slight smell of burnt rubber. Did an online search and best guess was the spider arm assy was broken. Ordered the spider arm assy, the rear tub seal and the tub seal. Make sure you get blue threadlocker - you'll use it multiple times during the reassembly. The washer is 9 years old and is heavily used. Used the online video on the appliancepartspros.com site to handle the repair. The... Read more

I removed the door, mostly so we could really clean the all the nooks and cranny's of the stove, and make the handle and gasket replacement easier. Attaching the new handle was not difficult, but did require some minor door dis-assembly. Removing the old gasket and putting on the new gasket was a breeze. The hardest part of the job was putting the door back onto the stove, but we got it done and the stove looks and works great. Read more

• Will not agitate
• Pumps but will not spin

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

Ordered and replaced bellow. It is important to supply the correct model number as my machine is a later model than the one used in the training video. The front panel is one piece, rather than two. Additionally, several of the fasteners were hex head screws, rather than torks. The Bellow is somewhat different having an opening for the light fixture. That said, the video was adequate to get the general idea of how to remove and replace the bellow. I found it very difficult to replace... Read more