Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement suspension rod kit for top-load washers. Installs between cabinet and wash basket to stabilize during spin. Replace if rods are worn or broken.
Our Maytag top load washer developed a bad slam during the spin cycle. Bad enough to shake the whole washing machine and make it move across the floor, sounded like it was going to destroy itself you could hear this thing in the furthest room in the house mind you it is on the opposite end of the house in the basement. For a while, you could do certain things to stop the issue or improve it, as you would expect that stopped working. I made sure the washing machine was level which I had to... Read more
Washer making loud grinding noise during spin or agitation? Drive clutch kit repairs worn clutch assembly. Moderate DIY repair, typically 30-45 minutes.
Replaced washer drive block and Cam. I called around and finally settled on Appliance Parts Pros because they helped diagnose the problem, told me what parts to replace and had videos to show me how to do it. In completing the repair I had to remove quite a few pieces of hardware in order to get at the part I was to replace. The videos helped but there is a learning curve while you familiarize yourself with the parts and figure out how the remove them. Eventually I got to a large nut that,... Read more
Fix a washer that won't spin or agitate with this drive hub kit. Transfers power from motor to basket. Moderate DIY repair with video guide included.
I watched a video on YouTube that showed my exact problem. It had a link to this part AP5665171 Hub and it showed how to fix it. It was a fairly simple fix. I did not even have to remove the tub. I popped the cap on top of the agitator plate (AGP), removed the bolt hold the AGP on. I tapped on the bolt several time to loosen it. Using an angled screw driver, carefully and slowly lifted up the edges of the AGP until I could use my fingers to carefully pull the AGP off the splined drive... Read more
Washer won't spin or shows F7 E1 error? The shift actuator controls cycle transitions. Moderate DIY repair with video guide available.
After internet search of symptoms, discovered that the hub that connects the drive shaft to the tub was stripped causing intermittent spinning which in turn caused the knocking and creating the unbalanced condition. Appliance Parts Pros got me the hub within a day and the other part a little longer due to snowstorm, but still timely. To replace the hub: Remove agitator by popping off plastic cap, undoing the bolt, take agitator of the shaft by tugging at it from side to side, if it seems like... Read more
The washer drive belt transfers motor power to the washer’s drive system so the basket spins and agitates. Replacing a stretched or broken belt helps stop squealing and slipping so cycles finish at proper spin speed.
What it does
What’s included One drive belt.
Install notes
This OEM Whirlpool belt is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.
This was my first attempt, ever, to repair a washing machine. After some internet research on the problems, I was able to determine that the shaft seal on the gearcase probably was leaking water into the gearcase with each use. No water was ever found on the floor, but when I turned the washer over to inspect the gearcase, I found a black, oily residue on the outside of it along with the same residue on the pulleys, the belt and the motor. I ordered a new gearcase, shift actuator, splutch... Read more
Washer won't start or stops mid-cycle? A faulty lid lock assembly prevents operation. Moderately difficult DIY repair—installation video available.
The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more
Lid won't lock or keeps clicking? This washer lid latch assembly fixes locking failures. DIY-friendly repair with video guide, typically done in 30-45 minutes.
Not wanting to spend hundreds of dollars on an appliance technician's service call, I searched online to troubleshoot the problems with my particular Maytag Washer Model Number MVWX500BW0. I stumbled across AppliancePartsPros.com and investigated there the most likely causes for my Maytag Washer's not agitating properly and not spinning at all. In order to acquire some additional information, I telephoned AppliancePartsPros.com and spoke with an extremely professional, knowledgeable and helpful... Read more
Fix a washer that won't fill or fills slowly with a new water inlet valve. Controls hot and cold water flow into the tub. Moderate DIY repair.
Replaced solenoid valve assembly. Easy repair. Read more
Washer won't spin or agitate? Worn gearcase gears cause thumping noises and prevent proper drum movement. Moderately difficult repair requires disassembly.
I replaced the gearcase and hub. With the help on line videos the process was straight forward and simple. Read more
Suspension bearing kit supports the tub assembly in top-load washers. Replace if bearings are worn, cracked, or causing excessive tub movement or noise.
After looking up the model number of my washing machine on AppliancePartsPros.com I ordered the suspension rod kit, two sets of tub centering springs (one spring per corner), a Ring-Tub (mine was breaking apart due to banging around) and a spare suspension bearing kit in case I need it later. I spoke to a very helpful customer service rep on the phone just before placing my order. They have customer service representatives answering the phone late at night. I was surprised. All of my parts were... Read more
Fix a washer that won't agitate or makes loud noises. This mounting screw secures the wash plate to the drum. Easy 2-minute DIY repair with a socket wrench.
Replaced it with a new wash plate. Read more
Washer won't spin or stops mid-cycle? A faulty lid lock strike prevents the lid from securing properly. Moderate DIY repair with included video guide.
This washer drain pump moves water out of the washer during drain and spin. Replacing a worn or failed pump restores proper draining so cycles finish on time and the basket can reach full spin speed.
What’s included One drain pump assembly.
This OEM drain pump is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Ordered the correct part/ Pump from this Awesome website and replaced the drain pump. Good to go!! Read more
Fix a washer that won't fill, fills slowly, or won't stop filling. This water inlet valve controls water flow during wash cycles. 30-minute repair.
Ordered the valve body from Appliance Parts Pro. It was very easy to find the part on their website. Ordering was simple. The part actually got here the next day. I received an email about 2 hours after I received the part that contained the tracking number. That is what is known as quick and reliable service. Part was a little hard to replace since I have big hands. There are 2 metal screws that hold the valve body to the washer that are in a small confined area. Unless you want to dismantle... Read more
Washer won't start because lid won't lock? This lid latch strike secures the washer lid during operation. Simple DIY fix in under 30 minutes.
Fix a washer that won't spin or agitate with this capacitor. Resolves F7E1 error code and motor running without drum rotation. Easy 20-minute DIY repair.
Bought one from you and replaced it. I friend did it for the family. Read more