Bath Fan Light Switch Parts

• Doesn't shut off
• Won't start
• Will not tumble

I realized my load of laundry was still wet after a normal drying cycle. My first action was to turn the dryer on (2010 gas Maytag centennial) and open the front port to look at the ignitor coil. It never turned orange so I knew there must be a problem with the primary circuit. I shut off the dryer, disconnected the power, pulled it away from the wall, shutoff the gas, and removed the back panel. I then disconnected the wires for the thermal fuse and checked its resistance with a multimeter.... Read more

• Won't start
• Element will not heat

After an internet search, the likely problem was a faulty "Element Switch.." I actually unplugged the stove and removed the switch (I did NOT disconnect the wires). I obtained the part number on the switch, disassembled it, observed that the contacts were highly degraded, reassembled the switch and reinstalled it back into the stove. This all provided confidence the SWITCH was faulty. One switch on the AppliancePartsPros.com website (AP2591804) looked exactly like the switch in the stove... Read more

• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

Much easier than expected, I was certain it had to be a water line but the solved everything Read more

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Won't start
• Element will not heat

The fix was to replace the infinite control switch on my Whirlpool range. A simple task. Read more

Went on line to check troubleshooting sites, then went on UTube to watch a video on how to repair the appliance, then ordered the part from you, the used the video as a guide to replace the part. worst part was getting the clip off the fan blades and the putting it back on Read more

• Too warm
• Clicking sound
• Won't start
• Freezer section too warm

I have a Kitchen Aid side by side refrigerator/freezer which is 8 years old. One day it just stopped cooling. At first I was just going to junk it and purchase a new one. However, I took off the lower back cover and noticed the compressor was not running. I knew from experience that these compressors need a starter capacitor and relay and it is not uncommon for these parts to fail. I looked on the Internet for a video which showed how to remove the parts. I also found a video which showed how... Read more

In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more

Shut off power in the panel box - easier than getting at the plug behind the unit. Had to take out the lower full-width drawer and the two crispers next. Removed two screws on the shelf above the wide drawer and removed the two shelf parts. Next was removing a screw from each wide drawer support. Then I pulled the support forward about an inch to disengage it from a post towards the back. There is a wiring connection in the right-hand support you will need to disconnect. Next, I removed a... Read more

• Won't start
• Timer will not advance
• Will not drain

First I checked the circuit breakers and power to the outlet, then next wanted to check the lid switch, but it wasn't where I had found it on older models. I could hear it clicking on and off as I raised and lowered the lid, but it wasn't visible. I drained the tub through a siphon hose to lighten the machine, so I could slide it away from the wall to better see. Couldn't see the switch anywhere and decided it must be hiding in the raised console, but was unsure of how to attack it without... Read more

Tried to fix with a non GE part, didn’t work. Your GE brand pressure sensor worked like a charm Read more

I was trying to troubleshot a problem I had with my GE dryer not starting. I went to AppliancePartsPros.com because they have excellent DYI videos on how to make repairs. I determined that the problem was in the push start switch. I ordered the switch online and it took 3 days to arrive. It took 5 minutes to replace the switch and the dryer works perfectly. Read more

After extremely poor support from WhirlpooI and researching numerous U-Tube videos, I fully troubleshot potential failed components and connections. All appeared to function properly, so I reassembled the unit and experienced the same problem as before. I then narrowed down the problem to either the Touchpad ($57+$8 shipping) or the control board ($295+shipping). If those did not work, then a new Microwave of better quality, reliability and support than original microwave, Unfortunately,... Read more

• Won't start

I replace the Infinite Switch and that seems to be the trick for keeping the temperture under control. Read more

It was a classic horror story, but with a happy ending! I called a classic, "regular" repair company that I obtained on-line. My Whirlpool was 2 months out of warranty, so the repairman charged a trip-fee of $95 that would be subtracted from the cost of my repair. "Lee" showed up an hour late, even though he was told that I had to leave for work by 10:30 (-He assured me that he would have me fixed by then). The refrigerator was rolled out of its spot, and Lee began to remove the back cover... Read more

Watched the attached video, then followed directions and installed the part ordered. Read more