Jbp21wb1ww Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

I spent hours searching for the right trays, knowing only that the stove is GE, and what the trays look like, including exact dimensions. I ordered one set that had exact measurements, and they even explained how the measurements are taken. But the trays were larger than described by 3/8 inch, and I had to pay shipping to return them. I suggested that they correct their description, but the lady did not think I was right. I said just measure them yourself, as per the method that your... Read more

I spent hours searching for the right trays, knowing only that the stove is GE, and what the trays look like, including exact dimensions. I ordered one set that had exact measurements, and they even explained how the measurements are taken. But the trays were larger than described by 3/8 inch, and I had to pay shipping to return them. I suggested that they correct their description, but the lady did not think I was right. I said just measure them yourself, as per the method that your... Read more

• Element will not heat
• Won't start

I ORDER THE TERMINAL BLOCK KIT, AND FOLLOW THE VIDEO HOW TO REPAIRE. IT IS VERY EASY.IT TOOK ME 10 MIN. Read more

I wasn't sure if it was the heating element surface, the receptacle or the switch. My wife does some canning so it had some good use. It turned out to be the receptacle. I purchased the element as well thinking it needed replaced anyway. All works now. All three items are/would be easy to change. Read more

REPLACE door hinges and door handle (about 30 minutes) 1. Open the door to the first catch. 2. Lift the latch keepers (stoppers) on the hinge. 3. Lift / pull the door away from the oven. 4. set on a flat surface with inside of door up. 5. Remove three screws on the bottom of the door. 6. Remove two screws on the inside towards of the top of the door (gold in color). These are long wood type screws. 7. carefully lift the inner door from the outer door. (NOTE: there are two metal pieces that the... Read more

I replaced all 3 remaining burner controls because they were all original (mid 1970s GE electric range w/coil burners), and one of the controls occasionally made arcing sounds when cycling the burner on and off. If a control is making odd noises - more than just a quiet metallic clicking as it cycles - it should be replaced. I'm assuming you have experience with the tools needed and can do simple mechanical assembly or disassembly, but have not previously worked with electrical equipment of... Read more

• Oven not heating evenly
• Little to no heat when baking

Checking for part replacement.....found your website.....I thought I had the right part, but called the tech/order line. Spoke to a very knowledgable tech, which she checked the stove serial # vs the part I thought I could use. The Tech advised that it WAS NOT and related the findings. I agreed after a short discussion and ordered the new element. The order was placed on Monday afternoon, on TUESDAY the FEDX truck pulled in with the replacement element!!!!!!! I watched the video offered on... Read more

• Won't start
• Element will not heat

I ordered the recommended Infinite Heat Switch Kit and Element Receptacle and Wire Kit and installed them. The latter was a breeze, appearing to be exactly the same as the original, except for the wire color. The switch, though, was another story. It is a RobertShaw "replacement" part, designed, it seems, for use in the greatest number of original units as possible. The most obvious difference between this switch and the original (besides its comparatively small size) is the long, segmented... Read more

I lifted the front hood and removed the back control panel cover. I then replaced two terminal blocks with the new kits. Perfect match except wires were a bit long. So I rolled them up neatly and tucked them away at the control center. Used electrical tape to band both sets of wire and protect them from the metal edges between the range and control area. I replaced the control cover and installed two new burners. Perfect installation. Read more

REPLACE door hinges and door handle (about 30 minutes) 1. Open the door to the first catch. 2. Lift the latch keepers (stoppers) on the hinge. 3. Lift / pull the door away from the oven. 4. set on a flat surface with inside of door up. 5. Remove three screws on the bottom of the door. 6. Remove two screws on the inside towards of the top of the door (gold in color). These are long wood type screws. 7. carefully lift the inner door from the outer door. (NOTE: there are two metal pieces that the... Read more

Tested the power to the unit by turning on the cooktop portion and saw that I had power to all of the burners. Turned the selector knob to broil and saw that the top element would heat up. I then turned off the breaker to the unit. I then decided to take out the baking element to do a continuity test. When I touched it, a 1.5 inch section fell out. Since that concluded my continuity test, I assumed I needed a baking element. After receiving the parts the NEXT DAY (amazingly great service... Read more

• Oven is too hot
• Little to no heat when baking

I was able to find the model number on the lower right hand side of the range/oven, a GE True Temp. I Googled it to find parts, and thought I had found the correct sensor, but was very pleased that the ApplianceParts sire suggested I check compatability again before the order. I would have ordered the wrong sensor kit other wise. I DID get the correct one order. It arrived on time. The tricky part was get the old sensor out without having to pull the oven/range combo out form the wall over... Read more

Fast delivery, great service Read more

I changed the motherboard - computer and also changed the motor in the freezer, because it was doing a howling sound every time it turned on. The repair technician asked for $500 for a repair and that is on top of the $230 I paid him two days before. I looked up the parts and decided to try myself and it paid off. Great instructional videos. Thanks Read more

Initially, I took it off, sanded it and painted with appliance touch-up. Still didn't look good so I ordered a replacement part and installed. Read more