Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix F2 or F34 error codes and inaccurate oven temperatures with this temperature sensor assembly. Moderate DIY repair, 30-60 minutes install time.
Easy peasy. We did the repair on a 9-year-old GE wall oven. Read more
The Fan Blower is an OEM part for GE ranges and wall ovens. This part helps to circulate air within the oven cavity. The fan blower ensures that heat is evenly distributed during cooking, contributing to consistent cooking results, and prevents the electronic components from overheating, which could lead to malfunctions or reduced lifespan of the appliance.
Causes of damage to the Fan Blower can include accumulation of debris and grease, which can obstruct the fan and strain the motor, and mechanical wear over time that affects the fan's efficiency.
Symptoms of a bad Fan Blower in a range include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
I had to take the top panels off and two back panels off. Took off about thirty screws. It was very dirty and dusty inside so I took the lower panels off as well to clean and vacuum it. The hardest part was getting the double oven out of the cabinet. Overall it was very doable. Read more
Oven door window pack assembly includes glass pane and frame for viewing food while cooking. Replace if cracked, shattered, or broken from heat damage.
Ordered part using phone support to confirm correct part. Came fast. Used video on YouTube (not exactly the same but close enough) to help. Need Torx #15, 20 but no other special tools. Straight forward job. Be careful handling the broken glass! Read more
The Cooling Fan Sensor Board is an OEM component for GE ovens and ranges. It is an electronic module connected to the main control board that monitors internal temperatures. An onboard thermistor sensor in the board regulates the convection fan relay and fan motor speed based on heating demands during the bake and broil functions.
Causes of a failed Cooling Fan Sensor Board can include moisture damage from spills or steam, faulty soldering connections, or manufacturing defects over time. Electronic components are also susceptible to normal wear from frequent heating cycles.
Symptoms of a bad board fan sensor include:
It is also compatible with Hotpoint, RCA, and KitchenAid wall ovens and range models using the same electronic control system.
The first attempt was to replace the sensor board on the lower cooling fan motor. That didn’t fix the problem. Next, I replaced the lower cooling fan. The oven is working correctly for now. Time will tell. The repair is fairly simple. 1. Pulled oven out of wall onto a platform that I built to be the same height as the bottom of the oven. 2. Took off the bottom back cover as well as the middle cover. I also had to take off a couple of pieces on the left side where the fan is. 3.... Read more
Halogen bulb illuminates your oven cavity so you can monitor cooking without opening the door. Replace when dim or burnt out. Verify fit with your model.
In my case everything is simple. The important thing was my order was received and my notifications kept me abreast until the delivery. Would not hesitate do deal with this company again in the future. Great professional service. Read more
10-32 machine screw secures panels, brackets, door hinges, and handles in ovens and ranges. Replace missing, stripped, or broken screws for tight fit.
All of the information on the web repair sites said "replace the hinges as the springs are worn out." Didn't fix the problem. The top of the door still wouldn't seal, and the. Leaning latch wouldn't catch the door unless you pressed on the door. The inside panel of the door was fatigued. Too many turkeys were set on the door over the years. The hinges are attached to that inside panel, so the stress points were bent over time. I replaced the inside steel panel. Took about an hour. Was able... Read more
Fix an oven door that won't open or close properly. This latch assembly includes the oven light switch and secures your oven door during operation.
Replaced part that plastic switch was a part of. Read more
Fixes oven not heating after self-clean cycle. This thermal safety switch cuts power when temperatures get too high. Simple diagnosis with continuity test.
Replace TCO Read more
ST10-16 X 7/16"
Move stove to unplug, remove rear center panel, indentify the two spade connectors that feed the heating element and remove (unplug) them. Remove two screws that hold the element to the inside rear wall of the stove and remove element. Install new element, plug in the previously removed spade connectors, re-install rear center panel, plug range (power) in, move stove back into place and enjoy. Read more
Seals oven door edges to prevent heat loss and maintain cooking temperature. Replace if worn, melted, compressed, or causing uneven heating. Confirm fit with your model number before ordering.
I ordered a replacement and pulled off the old one and put on the new one. Read more
Chrome-coated oven rack for wall ovens and electric ranges. Replace worn, damaged, or missing racks to restore cooking capacity and oven functionality.
I ordered them and they arrived. Read more
Black. 8-18 AB HXW 3/8
I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more
Covers fastener holes in your oven's inner door liner for a clean finish. Replace when missing, loose, or damaged to keep grease out. Confirm fit with your model.
This replacement screw fastens panels, brackets, or trim inside your appliance. Swapping in a new screw restores a tight, secure fit and helps stop rattles, looseness, or misalignment caused by missing or damaged hardware.
Fix an unresponsive control panel or oven that won't start with this pre-programmed electronic control board. Restores timer and temperature functions.
If your oven won't heat during bake cycles or bakes unevenly, this hidden bake element kit restores proper temperature. Mounts under the oven floor.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.