Agr5735gdb Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Gas smell
• Little to no heat when baking

I used the little video clip shown under the part and replaced it myself. Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

Online videos made this seem an easy fix. I unplugged the oven and removed the rear panel, then found where the temp sensor entered the oven. I unplugged the sensor's electric connector. Unlike the videos, this sensor screwed in from the inside of the oven, so I had to remove the 2 screws inside the oven which hold the sensor in place. Then I pulled the sensor out, careful not to tear the insulation with the wires and connector. Then I just pushed the new connector through the same hole and... Read more

• Little to no heat when baking

The bake (bottom burner) worked after replacing the ignitor. Becareful and do not drop the ignitor or the element will break. I found out the hard way. I bought the first ignitor at a local appliance store. After breaking that one, I found another at appliancepartspros.com for $20 cheaper. Thanks appliancepartspros!!! Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

Removed existing gasket and replaced with new gasket in less than 5 minutes. Very Easy. Make sure to remove the lower burner cover (inside the oven) which allows you to pull the end gasket material through the two circular openings in the frame. Read more

• Door won't close

Replaced the hinge and receiver. Read more

Had to drill out the portion of the old foot that was still in the grate. Cleaned out the opening. Popped in the new one and voilà- all fixed. I ordered 8 of the feet as I see this eventually happening to all of them. Read more

Start by removing the frame on the sides and bottom of the door. (Do not unscrew the corner screw holding the side frame and bottom together.) Be careful the glass will fall once the last screw is removed from the bottom so hold tight. Carefully remove glass and set aside. Remove top frame that held the handle. Once all the frame work and outer glass is removed unscrew the bracket that held the door handle from the door. Taking the top frame and bracket insert screw and washer and screw the... Read more

I ordered the brioler pan for my new stove from y'all it was a little small but that's the part number in the book that I got with the stoveyall did a great job fast shipping just what I ordered will by from again thanks Read more

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more

In an attempt to clean the range from the grease-gunk build-up, I had to remove the burner heads. Unfortunately, the 2 most used burner heads had immovable screws that locked them into the orifices underneath. After numerous hours in attempts to salvage the old burner heads and orifices attempting to remove the immovable screws, I gave up. Checked Maytag's website for parts and found nothing. Turned to AppliancePartsPros.com and found the correct parts for reasonable price in a matter of... Read more

In an attempt to clean the range from the grease-gunk build-up, I had to remove the burner heads. Unfortunately, the 2 most used burner heads had immovable screws that locked them into the orifices underneath. After numerous hours in attempts to salvage the old burner heads and orifices attempting to remove the immovable screws, I gave up. Checked Maytag's website for parts and found nothing. Turned to AppliancePartsPros.com and found the correct parts for reasonable price in a matter of... Read more

I ordered the replacement light module and install it. I was able to install the module without removing the walloven from the cabinet. Thank you for quick delivery of the module. Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Bought and installed new hinges. Repair took about an hour but I also cleaned all the glass inside and out on both oven doors. I had ordered extra screws as I read the old ones that hold the hinges were hard to get in as they were self taping but the screw labeled 5 next to the hinge were not the right ones. All old screws worked fine. You just need to put a little power to them to get them started. Easy repair. Read more