Door Lock Motor Switch Parts

• Doesn't shut off
• Won't start
• Will not tumble

I realized my load of laundry was still wet after a normal drying cycle. My first action was to turn the dryer on (2010 gas Maytag centennial) and open the front port to look at the ignitor coil. It never turned orange so I knew there must be a problem with the primary circuit. I shut off the dryer, disconnected the power, pulled it away from the wall, shutoff the gas, and removed the back panel. I then disconnected the wires for the thermal fuse and checked its resistance with a multimeter.... Read more

• Pumps but will not spin
• Will not agitate
• Burning smell
• Touchpad does not respond

My whirlpool washer was no longer spinning, so my first stop was YouTube where I found the video from AppliancePartsPros showing how to replace the motor coupling. In addition to the replacement guide, Matt also shows you how to diagnose the problem by looking for rubber shavings under the washer. Seeing the rubber shavings under the washer, combined with the fact that the washer still drained meant that the motor was still working, so something else in the drive train was bad. I took the... Read more

• Won't start
• Element will not heat

After an internet search, the likely problem was a faulty "Element Switch.." I actually unplugged the stove and removed the switch (I did NOT disconnect the wires). I obtained the part number on the switch, disassembled it, observed that the contacts were highly degraded, reassembled the switch and reinstalled it back into the stove. This all provided confidence the SWITCH was faulty. One switch on the AppliancePartsPros.com website (AP2591804) looked exactly like the switch in the stove... Read more

• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

Much easier than expected, I was certain it had to be a water line but the solved everything Read more

I got online and found AppliancePartsPros.com. I found others had the same problem, and had replaced the switch, with my model number your rep got me the exact switch and a video on how to change it. It took approx 15-20 min . was very happy with the service, will use again in future if needed. Gary Read more

• Will not tumble
• Noisy
• Shuts off too soon

My 12 year old Kenmore dryer problem started about 3 years ago with the motor just stopping. My thing was: I would turn it off and turn the drum by hand about halfway around and it would work again. Last month, my wife said it stopped again and its making a loud noise, but when I did "my thing" it still made a loud squealing noise (like I was killing a mouse). I made time to work on it the next day, I took it apart, using the video instructions from AppliancePartsPros, I removed the top,... Read more

Went on line to check troubleshooting sites, then went on UTube to watch a video on how to repair the appliance, then ordered the part from you, the used the video as a guide to replace the part. worst part was getting the clip off the fan blades and the putting it back on Read more

• Won't start
• Element will not heat

The fix was to replace the infinite control switch on my Whirlpool range. A simple task. Read more

Noticed that lid lock light was not on, googled problem, ordered parts, working on 3rd day. Read more

• Too warm
• Clicking sound
• Won't start
• Freezer section too warm

I have a Kitchen Aid side by side refrigerator/freezer which is 8 years old. One day it just stopped cooling. At first I was just going to junk it and purchase a new one. However, I took off the lower back cover and noticed the compressor was not running. I knew from experience that these compressors need a starter capacitor and relay and it is not uncommon for these parts to fail. I looked on the Internet for a video which showed how to remove the parts. I also found a video which showed how... Read more

This was to address an E:09 fault code on a Bosch dishwasher. I swapped out the Circulation motor and heater assembly. The video given on APP.com was for a different model, but more or less the same. The video gave me confidence enough to order the part and attempt it. The significant difference was that in the video, the assembly is easily accessible from the bottom of the unit. On my unit, however, the bottom is a closed plastic pan that isn't easily removable, likely requiring removal of the... Read more

The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

When I looked up the part number there was a handy video that popped up. I watched the video and thought "how easy!" so, I ordered that part and waited. The next day, I thought I better start to take the door off of my dryer (because that's what the video instructed, and I wanted a head start) so as I was going into the garage to get my tools, my son came in with a small package. It was the part. That came, to quote another customer, "Crazy Fast!" All the way from Kentucky to California! ... Read more

• Won't start
• Timer will not advance
• Will not drain

First I checked the circuit breakers and power to the outlet, then next wanted to check the lid switch, but it wasn't where I had found it on older models. I could hear it clicking on and off as I raised and lowered the lid, but it wasn't visible. I drained the tub through a siphon hose to lighten the machine, so I could slide it away from the wall to better see. Couldn't see the switch anywhere and decided it must be hiding in the raised console, but was unsure of how to attack it without... Read more

• Lid or door won't close
• Won't start

Not wanting to spend hundreds of dollars on an appliance technician's service call, I searched online to troubleshoot the problems with my particular Maytag Washer Model Number MVWX500BW0. I stumbled across AppliancePartsPros.com and investigated there the most likely causes for my Maytag Washer's not agitating properly and not spinning at all. In order to acquire some additional information, I telephoned AppliancePartsPros.com and spoke with an extremely professional, knowledgeable and helpful... Read more

• Will not drain

I've opened sump housing to check for clogging but it was clean. When I removed check valve to inspect it I've found out that the round part of the valve was missing so I figured it might've blocked the water exit at drain hose or something like that. So I pulled the dishwasher out to get a full access to drain hose connector and the pump. Upon disconnecting the drain and checking its connector I indeed found the round piece totally blocking the hose and acting as a seal. I removed the piece... Read more