Ksm5psgr Parts

I read a few of your reviews and found that a, "Phase Control Board" may be the problem. It was! Talk about easy to install... It was super easy! I decided to order the, "Speed Control Plate" also as a precaution (Shipping was one price - and it arrived the very next day, Wow! I didn't expect that.) With my screwdriver and good lighting. I fixed it myself! My husband is still in shock. I used forceps to install the, "Speed Control Plate," because I needed something to hold the tension wire - at... Read more

This was a problem that I'd had previously with this mixer. The worm gear, which is designed to fail (so that more serious damage does not occur to the motor), did fail while I was mixing some multi-grain bread dough. After the previous failure (pre-youtube days), I took the machine in for repair. The repair-shop cost came to about $150 in labor. Parts were extra. This time, I decided to do the repair myself, since I figured that I knew what was wrong. I found the appliancepartspros... Read more

• Will not tumble
• Noisy
• No heat or not enough heat
• Takes too long to dry

The blower wheel had been previously “repaired,” but the repairman did not install a retaining clip or clamp, so the new part was destroyed in about a year and a half, as the motor shaft rounded all the square edges in the plastic hub. The old blower wheel came off easily and the new part was a perfect fit. The center clamp that comes with the blower wheel kit would probably hold it in place by itself, but I also purchased and installed the retaining clip (#35) as well, because the end of the... Read more

I read a few of your reviews and found that a, "Phase Control Board" may be the problem. It was! Talk about easy to install... It was super easy! I decided to order the, "Speed Control Plate" also as a precaution (Shipping was one price - and it arrived the very next day, Wow! I didn't expect that.) With my screwdriver and good lighting. I fixed it myself! My husband is still in shock. I used forceps to install the, "Speed Control Plate," because I needed something to hold the tension wire - at... Read more

This was a problem that I'd had previously with this mixer. The worm gear, which is designed to fail (so that more serious damage does not occur to the motor), did fail while I was mixing some multi-grain bread dough. After the previous failure (pre-youtube days), I took the machine in for repair. The repair-shop cost came to about $150 in labor. Parts were extra. This time, I decided to do the repair myself, since I figured that I knew what was wrong. I found the appliancepartspros... Read more

I bought a new speed control plate and phase control board. Since I was ordering these parts, I ordered two new motor brushes as well. All parts arrived two days after ordering, and mixer is back up and running fine. Read more

I bought the 3 components- Speed Control Plate, Speed Governor, and Phase Control Board after researching what components could be the culprit of the issue. I started out by replacing the speed control board and the governor, which had no effect on the issue. I replaced the Phase Control Board and the issue was resolved. All in all about 1.5 hours of work to do all 3 parts from tear down to button-up. Read more

This time I replaced the front and rear bearings and thrust bearing and all the gears. The hardest part is thoroughly cleaning out all the old grease. After re-greasing and assembly mixer ran like new. I wish a more robust worm gear was available. A snap ring plier is a must for this job. Read more

Replaced gears, removed old grease & added new grease to parts. Read more

Checked out You tube video. Easy tune up. One gasket was damaged and I did not notice that the brush holders has no brushes. I believe a quick call to Appliance parts pros will fix this, besides I need a few more parts. I expect to get another 20+ years from this KitchenAide mixer, once repairs are competed. Watch out for the single lock washer located on the rear upper housing screw, you don't want to lose this! Read more

My KitchenAid Professional Series 6 mixer which is about 20 years old suddenly stopped working. The motor would run but the beater would not complete a full circle without a push from me. I took the gearbox apart to figure out why the beater would not turn and discovered that the worm follower gear had most of the teeth stripped from it. I believe this was caused by a lack of grease. As I removed the gearbox cover, I noticed that most all the grease had been thrown to one side of the gearbox.... Read more

Replaced the center gear and since they sent the hub along I replaced that too just to be safe. Used the live chat before ordering to make sure I was ordering the correct part. The person I chatted with was very nice and very helpful and parts came in good shape, and just as ordered. Replaced the stripped gear the next day and added a bunch of grease and the mixer works like new. Was very impressed with their diagrams and helpful videos as well as their large selection of parts. The other... Read more

Took my time and disasembeld the mixer and cleaned old grease from internal gear box. put new greas in and put it back together. A piece of cake!!!!! Read more

God Bless Youtube! Searched "replace motor in Kitchen Aide mixer" and found an excellent tutorial on the subject made by AppliancePartsPros.com. Followed the instructions with my smart phone and purchased a new motor and brushes. Fixed the $500 mixer for $50.. Runs like new but now have to change the color per her request. Excellent company to deal . Read more

God Bless Youtube! Searched "replace motor in Kitchen Aide mixer" and found an excellent tutorial on the subject made by AppliancePartsPros.com. Followed the instructions with my smart phone and purchased a new motor and brushes. Fixed the $500 mixer for $50.. Runs like new but now have to change the color per her request. Excellent company to deal . Read more

• Touchpad does not respond

Replaced old parts added new ones. So excited. My 26 year old kitchen aid is functional and amazing. Read more