Mgs5770 Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Gas smell
• Little to no heat when baking

I used the little video clip shown under the part and replaced it myself. Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

Online videos made this seem an easy fix. I unplugged the oven and removed the rear panel, then found where the temp sensor entered the oven. I unplugged the sensor's electric connector. Unlike the videos, this sensor screwed in from the inside of the oven, so I had to remove the 2 screws inside the oven which hold the sensor in place. Then I pulled the sensor out, careful not to tear the insulation with the wires and connector. Then I just pushed the new connector through the same hole and... Read more

• Won't start

Replaced srark module Read more

• Door won't close
• Oven not heating evenly

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

• Gas igniter glows, but will not light
• Won't start
• Element will not heat

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

Appliances will be sold with the house so the old oven racks were no longer shiny. Replacement racks present a better looking oven. Read more

• Gas smell
• Won't start

I replaced the burner head. I turned off power to the stove, although I did not turn off the gas. I gave the old burner head a slight twist counter-clockwise until it lifted off the stove. I used the pliers to pull the wires from the old burner, then placed them onto the contacts on the new burner. Set it in place, and gave it a clockwise twist until it was snug. This stove originally came with gaskets beneath the burners, but the info for the replacement part stated that a gasket was not... Read more

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more

• Door won't open or close

I replaced the hinge due to the hinge spring breaking. To replace the hinge you do the following: 1. Disconnect power to stove, either at circuit box or at outlet. 2. Lift door off of outside hinge arms ; no screws are used to attach the door to the hinge 3. Remove two screw on under side of cook top, one on each side. 4. Disconnect cook top connector. 5. Lift cook top off 6. Remove screws from top rail of stove that hold the side panel. 7. Remove the screw on the back that hold the side... Read more

These are very easy to replace ,just gave the old one a quarter turn lifted it out took the two wires off (noted where each one will go on the new burner ) pop the wires onto the new burner put it on and good to go. Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Bought and installed new hinges. Repair took about an hour but I also cleaned all the glass inside and out on both oven doors. I had ordered extra screws as I read the old ones that hold the hinges were hard to get in as they were self taping but the screw labeled 5 next to the hinge were not the right ones. All old screws worked fine. You just need to put a little power to them to get them started. Easy repair. Read more

Removed screws all around one door. Once the door shells separated I could reach all of the parts I needed to replace. It was a breeze. I wrote down the oven model number and the part number on the back of the handle. I ordered the part online, expecting to see it in a few days. To my surprise it showed up the next day. Thanks It went right back together in less than a half hour. Read more