Ymhwe25iyl00 Parts

• Will not drain
• Noisy
• Burning smell
• Pumps but will not spin

There was a loud noise from my washer during the drain cycle. (The washer seemed to drain just fine.) It was pretty easy to determine that the noise was coming from the drain pump. (Which for my washer is behind the front lower inspection panel on the right side front.) I inspected the outside of the pump for any physical damage and verified no issues with the pump or the mounts. Everything seemed ok. I then checked the drain pump filter(You will need something to catch water if you do... Read more

• Lid or door will not open
• Won't start

Did lots of internet research. Narrowed problem down to three things - door lock latch, control unit, and motor control unit. Figured out how to run the diagnostic test program, which showed a F22 (door lock) error. Removed and ohm tested the door lock (pins 1 & 3). Found door lock latch to be defective. ordered new one and installed it. YouTube video helped a lot. https://www.youtube.com/watch?v=_SjU6k5bpSs So far, so good. Have only done a few loads. New door lock latch tested fine. Read more

• Shakes and moves

We looked online at AppliancePartsPros.com under the symptoms and found it was most likely caused by the shocks. Of course there was a repair video showing how to replace all four shocks step by step, and there was a link for purchasing the four shocks at the bottom of the video. Our repair didn't go quite as quickly as on the video because we are novices, but we were able to do the repair ourselves and, once again, saved ourselves a ton of money! Now we have a very quiet washer and dryer again... Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

• Lid or door won't close
• Lid or door will not open

I removed the two screws and all the pieces that were broken. Went online to Appliance parts.com, searched for the part using the model number from the machine and ordered the part . part arrived in 2 days and with a Phillips screwdriver was installed in less than 5 minutes. Read more

Watched a youtube video and it was easy to do. Read more

Followed your video instructions. It was invaluable. The toughest part was getting the seal on the back of the drum. Your technician made it look very easy. Once that was on, the rest was pretty easy. The control panel on my Whirlpool Duet washer had a holding screw at the bottom center of it. It wasn't shown in the video, but it was easy to figure out. If you are changing the boot, change the clamp as well. Read more

• Will not stop filling with water
• Leaking

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more

• Will not fill with water

I ordered this new valve, and voila!!! No more using up all the hot water to wash everything. Now I can do all of my laundry with cold water, like I prefer to. Read more

• Won't start

Replace the water temperature sensor and still had the error code. While I had the back of the machine open I ran the washer. I traced the black wires from the temperature sensor and wiggled them as the washer was running. At one zip tie every time i moved the wires the washer would stop running and the error code would flash. Sure enough, like many others posted, the vibration from the machine had split the wire. I spiced the wire back together and have not had a problem since. Read more

Removed the leaking hoses and seal. Installed the new ones. They all fit perfectly. The disassembly/reassembly of the washer took the most time. Read more

Took the old part off and fitted the new one. I used the old plastic ball from the old hose and it worked fine. Next time I would replace the original clamp with a 4 inch hose clamp. The original clamp is way tooooooooooo hard to put back on....with a different clip it would be a 10 minute job at most. Read more

Called a repair man after not being able to determine the exact problem. Narrowed it down to valves, level switch or mother board. Repairman took money for parts and then said he couldn't find them. Went online and found this site, ordered parts Monday, had them by Thursday noon. Had machine running by 1. Read more

• Leaking

Took off cover, installed new parts. Read more

First remove the back from the washing machine. Top of the machine came off simple. To replace springs, I took a crow bar but it on the right side underneath where one of the springs should be. Lift the tumbler up remove and replace the spring. Did the same thing to the other side. On the tumbling unit there are spaces for three shock absorbers. Mine only had one shock in the middle. I put two new springs, one in the front and one in the rear. Then I replaced the right side spring with two new... Read more

Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine. Read more