Sears Parts

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

Dryer lint screen door provides access to the lint filter. Replace if cracked, broken, or won't close properly. Verify fit with your model number.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

This is a small tube of silicone-based gasket sealer used to bond and seal gaskets during washer repairs. It creates a watertight seal between mating surfaces to prevent leaks around tub components or pump housings. Use this adhesive when replacing gaskets or resealing joints where the original sealant has deteriorated and water is leaking.

This is a small lever or catch that engages the door switch when the dryer door is closed, signaling the dryer that it is safe to operate. It also interacts with the belt switch mechanism to detect proper belt tension. Replace this part if the dryer does not start when the door is shut, runs with the door open, or if the lever is visibly broken or worn.

Vinyl door seal lines the dryer door perimeter to block air leaks and cushion closure. Replace when worn or cracked to restore a tight seal. Verify fit by model.

Screw: 8-16 x 3/8 inch.

This control display board is the appliance's user-interface module that operates the front control panel and display, giving visible status and responding to user input. Replacing it fixes display and control issues safely and simply. What it does:

• Provides the visible display and interprets button/touch inputs so the appliance responds to selections.
• Can produce unresponsive or intermittent buttons/touch controls and erratic indicator lights.
• May trigger control errors or prevent cycle selection if damaged.

• Disconnect all power before starting — turn off breaker or unplug the appliance.
• Handle the board carefully and avoid static discharge; use a grounding strap if available.
• Remove and reattach wire connectors and mounting hardware gently; note connector orientation.
• Reconnect power and verify functions before reassembling trim or covers.

The 24-inch shave plate scrapes snow down to the pavement surface and is located at the bottom front of the snow blower. Replace when the plate is worn, bent, or no longer provides effective ground clearance.

Dryer won't heat or flames are yellow? This butane burner orifice meters gas flow for clean, reliable ignition. Required for butane conversions.

White end cap kit with left and right caps for the dryer control panel ends. Provides finished appearance and protects panel edges.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

This bulkhead is the front tub housing that supports the washer drum and seals the washer cabinet to help contain water. Replaces a cracked or corroded housing to restore proper drum alignment and help prevent leaks. What it does:

• Provides structural support for the washer tub and drum assembly
• Forms the front seal surface to help keep water inside the washer
• Helps maintain correct drum alignment to reduce noise and wobble
• A failing bulkhead can cause visible leaks, excessive vibration, or rubbing noises

• Disconnect power and water supply before starting any repair
• Inspect surrounding seals, gaskets, and mounting hardware when replacing the bulkhead
• Replacement may require partial disassembly of the washer cabinet and drum; follow OEM instructions

Right handed Hinge

Snow blower won't move forward or loses traction? A worn friction wheel is usually the culprit. This rubber disc contacts the drive wheel to propel your machine.

Auger not turning or moving slowly? This snowblower worm gear connects the driveshaft to auger blades. Moderate DIY repair restores snow ejection.