Parts for Frigidaire GLRSF236JD1: 05 - Shelves Parts

This basket trim is the replacement edge trim that snaps onto the dishwasher rack to protect dishes and prevent wear along the rack perimeter. It restores a smooth edge and helps keep items from catching or chipping. What it does:

• Covers and protects the exposed metal edge of the dishwasher basket/rack.
• Helps prevent dishes and glassware from chipping or snagging on a rough rack edge.
• Restores a finished appearance to a damaged or missing rack trim.
• Reduces contact noise and wear where dishes meet the rack perimeter.

• Disconnect power to the appliance before beginning any repair work.
• This part typically snaps onto the rack edge; remove the rack for easier access.
• Replace any broken clips or adjacent trim sections to ensure a secure fit.
• If plastic is brittle or rack is heavily corroded, consider replacing adjacent components rather than forcing installation.

This pizza shelf is a direct-replacement oven shelf designed to support pizzas and other flat bakeware for stable, even cooking. Restores a missing or damaged shelf so trays and pans sit level during use. What it does:

• Provides a flat, stable surface for baking pizzas, sheet pans, and similar items
• Replaces a warped, bent or missing pizza shelf that prevents level cooking
• Helps keep cookware centered and supported to reduce sliding or tipping
• Durable finish resists everyday oven use and helps maintain even heat exposure

• Slide shelf onto existing oven rack supports until it sits securely; no tools typically required
• Allow oven to cool before removing or installing the shelf to avoid burns
• Clean with non-abrasive cleaners; avoid harsh scrubbing that can damage the finish
• Follow your oven manufacturer's instructions for safe use and placement

The Upper Crisper Pan is an OEM replacement part for Frigidaire refrigerators. Located on the slidable tracks inside fresh food section that holds the vegetables/produce. The pan measures about 16-1/2 inches wide by 8 inches high by 16 inches deep. The drawer front is not included for lower pan order 5303289501.

Causes of a bad upper crisper pan may be cracks in plastic developing over extended use, stains that render it unsuitable for food contact, or warping from exposure to wet environments inside the crisper.

Symptoms of a bad upper crisper pan include:

• Leaks and stains below the drawer from collected liquids overflowing the pan
• Difficulty organizing and separating different items stored in the crisper

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Lower Storage Pan is an OEM part for Frigidaire refrigerators. This storage pan is designed to fit in the lower section of the refrigerator, providing an ideal space for storing fresh produce, meats, and other perishable items. Drawer front not included. For upper pan order 5303289500.

Over time, the lower storage pan can become damaged due to regular use, overloading, or accidental impacts. Cracks, breaks, or warping can compromise its functionality and lead to issues with storing items properly.

Symptoms of a bad Lower Storage Pan include:

• Cracks or visible damage to the pan
• Difficulty sliding the pan in and out of its compartment
• Items not being held securely within the pan
• Pan not fitting correctly in its designated space

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Left hand side. For right hand side use 215002401

This storage pan front is the replacement drawer front that restores the look and function of a refrigerator storage bin, keeping contents contained and helping drawers open and close smoothly. Designed to match OEM fit and finish. What it does:

• Replaces a cracked, chipped or broken drawer/front that won't stay attached
• Keeps stored food and produce contained in the lower storage bin
• Restores proper alignment so the drawer slides and seals correctly
• Prevents items from falling out when opening or closing the drawer

• One storage pan front (single piece) as shown

• Remove contents and the full drawer/bin before replacing the front to avoid damage
• Most replacements snap or slide into existing tracks; no special tools required for many models
• Handle part carefully to avoid scratching; wear gloves if needed to protect hands
• Ensure proper seating before use

Size: Approx. 16.31 inches X 17.32 inches. This is clear glass

Size: Approx. 15 inches X 16 1/4 inches. This is clear glass

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

Tank itself is not included in this kit. Kit includes tubing,screws & two John Guess fittings & instructions.

Left hand side. For the right hand side order 218015601

Right hand side. For the left hand side order 218015501

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This replacement screw secures panels, brackets, and other components in your appliance. Replace missing or stripped hardware to restore a tight, rattle-free fit and keep assemblies aligned the way the manufacturer intended.

• Fastens the designated component to the appliance cabinet or assembly
• Helps reduce looseness, vibration, and rattling
• Replaces missing, corroded, or stripped screws
• Supports proper alignment of panels, trim, and brackets

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to the original location; retain any reusable clips or washers
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten into plastic or thin metal

Right hand side. For the left hand side order 241674401

Left hand side. For the right hand side order 241674402

This humidity control is the sliding damper used on the refrigerator crisper drawer to adjust air flow and humidity. It helps preserve fruits and vegetables by limiting airflow to maintain a higher-moisture drawer environment. What it does:

• Opens or closes the crisper drawer vent to increase or reduce airflow and moisture exchange.
• Lets you set higher humidity for produce that needs moisture or lower humidity to reduce condensation.
• Commonly replaced when the slider is cracked, missing, loose, or no longer moves smoothly.
• A damaged control can contribute to dried-out produce or excessive moisture buildup in the drawer.

• Unplug the appliance before inspecting or replacing the part.
• Remove the crisper drawer per your model's instructions to access the slider; replace with the new control in the same orientation.
• Handle plastic parts gently to avoid cracking; test slider movement before reassembling.

Right hand side. For left hand side use 215002301

This cantilever shelf clip secures a refrigerator cantilever shelf in place so shelves stay level and stable. It replaces a cracked or missing clip to restore proper shelf support and prevent shifting or slippage. What it does:

• Holds the cantilever shelf bracket/tier in the refrigerator liner to keep the shelf properly positioned
• Prevents shelf from tipping, sliding, or falling when items are placed on it
• Replaces worn, cracked, or broken clips that no longer grip the shelf brackets
• Works with standard cantilever-style shelving systems used in many refrigerators

• One cantilever shelf clip

• Remove food and glass shelves/trim as needed for safe access before replacing the clip
• Align clip with the shelf bracket slot and press firmly until it snaps into place; do not force beyond normal fit
• Handle glass shelves carefully to avoid breakage; wear gloves and eye protection if needed