Parts for Kenmore 253.60504411 (25360504411, 253 60504411): Shelves Parts

The Freezer Shelf is an OEM replacement part for  Frigidaire freezers. It is a sturdy and durable wire or glass shelf designed to provide ample storage space within the freezer compartment, allowing you to organize and easily access frozen items. Measuring approximately 24-1/2" W x 12-1/2" D x 5/32" H, the shelf requires no hardware or tools for installation.

Causes of needing to replace a freezer shelf can include physical damage from impact or excessive force, warping or deformation due to temperature fluctuations or moisture over time, or general wear and tear from repeated use.

Symptoms of a bad freezer shelf include:

• Visible cracks or bends in the shelf material
• The shelf becoming loose or unstable, causing items to slide off
• Difficulty sliding the shelf in and out of its designated position

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This air diffuser kit replaces the vent/damper assembly that meters cold air from the freezer into the fresh-food section. It restores proper airflow and temperature balance when the original diffuser is stuck, broken, or leaking around the vent.

• Regulates and directs airflow from the freezer to the refrigerator compartment to maintain set temperatures
• Opens/closes the damper to reduce warm or cold spots in the fresh-food section
• Helps resolve symptoms such as a warm refrigerator with a normal freezer, weak airflow at the diffuser, temperature swings, or frost/condensation near the vent
• Replaces cracked housings, missing seals, or jammed/broken damper blades

• Disconnect power before servicing; wear cut-resistant gloves
• Remove shelves/covers to access the diffuser; note part orientation and screw locations
• Ensure all seals seat properly to prevent air leaks; do not overtighten plastic fasteners
• Restore power and allow up to 24 hours for temperatures to stabilize; adjust controls as needed

This refrigerator door gasket creates an airtight seal around the door to help keep cold air in and warm air out, preserving food freshness and helping the appliance run efficiently. What it does:

• Seals the door to maintain proper internal temperature
• Reduces frost and moisture buildup by preventing warm, humid air from entering
• Helps reduce compressor runtime caused by air leaks
• Restores a tight magnetic seal for reliable door closure

• Disconnect power before starting any repair.
• Remove the old gasket and clean the gasket channel; install new gasket, aligning the magnetic edge and corners.
• Check for full compression around the door; adjust or reseat as needed for an even seal.
• Allow the gasket to settle and recheck after 24 hours; avoid using sharp tools that could damage the seal.

The Light Switch is an OEM replacement part for Frigidaire refrigerators. This switch controls the interior light of the refrigerator, turning it on when the door is opened and off when the door is closed. It ensures that the refrigerator is properly illuminated, making it easier to find items inside.

Causes of a bad light switch can include electrical malfunctions, physical damage from repeated use, or wear and tear over time.

Symptoms of a bad Light Switch include:

• Interior light not turning on when the door is opened
• Light flickering or intermittently turning on and off
• The refrigerator light staying on even when the door is closed

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Light Bulb (40W) is an OEM part for Frigidaire appliances. Specifically designed to fit and function with Frigidaire models, this 40-watt bulb illuminates the interior of your oven, making it easier to check on the progress of your baking or roasting without opening the oven door.

Over time, oven light bulbs can burn out or be damaged from high temperatures or accidental bumps during cleaning or cooking. A functioning light bulb is crucial for the optimal operation of your oven, enhancing visibility and improving your cooking experience.

Symptoms of a bad Light Bulb include:

• The oven interior remains dark when the light switch is engaged.
• Flickering light, indicating a loose connection or nearing the end of the bulb's lifespan.
• Completely non-functional light, which can hinder your ability to monitor cooking progress.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This refrigerator light socket holds and powers the interior bulb so you can clearly see inside. Replace a cracked, heat-damaged, or loose socket to restore reliable illumination when the interior light won't work or flickers.

• Provides the electrical connection and mounting point for the compartment light bulb
• Fixes symptoms such as no interior light with a known-good bulb
• Addresses intermittent flickering when the door is opened or closed
• Helps resolve visible charring, melting, or broken contacts on the socket
• Corrects a loose bulb that won't stay seated or lit

• Disconnect power to the refrigerator before servicing; remove the light lens/cover and bulb
• Note wire positions; release the old socket from its mount
• Transfer wires to the new socket one lead at a time and seat the socket fully
• Reinstall the bulb and cover; restore power and test
• Use only the bulb type and wattage specified for your model

This control box housing protects and secures the range/dryer/washer electronic control assembly, keeping wiring and the control board mounted and shielded from debris and heat. It restores a stable enclosure for reliable control operation. What it does:

• Provides a mounting enclosure for the appliance electronic control board and associated wiring harnesses
• Shields circuits from dust, moisture and incidental contact that can cause shorts or intermittent operation
• Keeps control components properly aligned so knobs, switches or displays sit correctly
• Helps prevent vibration-related loosening or damage to the control assembly
• Can eliminate symptoms like loose or rattling controls, exposed wiring, or intermittent control behavior when the housing is broken

• Disconnect power (unplug or turn off breaker) before any service to avoid shock or damage
• Handle the control board and ribbon cables carefully; transfer the PCB and fasteners from the old housing to the new housing if required
• Use the manufacturer-recommended screws/fasteners and correct alignment before restoring power

The Control Box Assembly is an OEM part for Frigidaire refrigerators. This complete assembly includes the electronic components and housing necessary to manage the refrigerator’s operations, such as temperature regulation, defrost cycles, and other vital functions.  

Causes of a bad control box assembly can include electrical surges, moisture damage, or normal wear and tear over time. Additionally, physical damage or faults in the wiring can lead to control box failure.

Symptoms of a bad control box assembly include:

• The refrigerator not cooling properly
• Error codes displayed on the control panel
• Inconsistent or fluctuating temperatures
• The refrigerator or freezer not defrosting as needed
• Unresponsive control buttons

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Temperature Sensor (10K NTC) is an OEM replacement part for Frigidaire refrigerators. This sensor monitors the internal temperature of the refrigerator or freezer compartment, sending signals to the control board to regulate cooling cycles. It ensures the appliance maintains the correct temperature for optimal food preservation.

Temperature sensors can fail due to wear over time, electrical issues, or exposure to moisture. A malfunctioning sensor can cause inaccurate temperature readings, leading to improper cooling or freezing.

Symptoms of a bad temperature sensor include:

• Fluctuating or incorrect temperatures in the refrigerator or freezer
• Food spoiling faster than expected or freezing inappropriately
• Error codes related to temperature regulation
• The refrigerator running continuously or cycling too often

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a sliding shelf frame that is used on the interior of many models of refrigerators. The shelf frame supports the shelves used to hold food and beverages inside the appliance. Regular use can cause wear and tear to the sliding shelf frame.No specific tools are needed to replace this part. Open the fridge to access the damaged shelf. Pull the entire shelf out of the appliance and gently remove the glass shelf from the plastic frame. Insert the glass into the new frame and place it in the refrigerator. Make sure it is secure before use.This sliding shelf frame is designed for use with refrigerators manufactured by Kelvinator, Frigidaire, Crosley, Kenmore, and Westinghouse. It is sold as an individual product. This is an authentic OEM replacement part that is directly sourced from the manufacturer.

The Frigidaire humidity control slide is an OEM replacement part responsible for regulating and adjusting the humidity levels within the crisper drawers of a refrigerator. This slide is found on the fresh food drawer to allow adjustment of the amount of moisture retained in the crisper drawers, which is essential for preserving the freshness and crispness of fruits and vegetables.

By adjusting the humidity control slide, users can create an ideal environment for different types of produce, ensuring that they stay fresh for longer periods and preventing food waste from wilting or drying out prematurely.

This part fixes the following symptoms

• Inability to adjust or control the humidity levels within the crisper drawers.
• Produce items wilting or drying out quickly due to improper humidity regulation.
• The control slide becoming loose, stuck, or difficult to move.

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Crisper Cover Frame is an OEM part for Frigidaire refrigerators. This parts serves as the structural frame for the crisper drawer section of the refrigerator, providing support and a level surface for the crisper drawers. It typically sits above the crisper drawers, holding the glass shelf in place and separating the drawers from the rest of the refrigerator. 

Over time, the crisper cover frame can become damaged or wear out due to frequent use, overloading, or accidental impacts.  

Symptoms of a bad Crisper Cover Frame include:

• Visible cracks or breaks in the frame
• Difficulty fitting or securing the glass shelf properly
• The crisper drawers not sliding in and out smoothly due to misalignment or instability of the frame
• Sagging or warping of the frame, affecting its ability to support the shelf and drawers

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Crisper Pan is an OEM replacement part for Frigidaire refrigerators. This high-quality crisper pan measures approximately 18 inches in length, 12 inches in width, and 8 inches in height. It is made of durable plastic material that is designed to withstand the rigors of everyday use. This crisper pan features a clear design that makes it easy to see the contents inside. It also has a humidity control feature that helps keep fruits and vegetables fresh for longer periods of time.

Symptoms of a failing Crisper Pan include:

• Cracks or breaks in the pan 
• Warping or damage that prevents the pan from sliding in and out  
• Scratches or cloudiness on the surface that impairs visibility  

Causes of a bad Crisper Pan can range from overloading it with too much weight, which can lead to cracks or warping, to normal wear and tear from sliding the pan in and out of the refrigerator. Accidental impacts, such as dropping the pan while cleaning, can also cause damage.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Front Shelf Trim is an OEM part for Frigidaire refrigerators. This part enhances the appearance and functionality of refrigerator shelves by providing a finished look and preventing items from sliding off. The trim snaps onto the front edge of refrigerator shelves, adding stability and a sleek, polished appearance to the shelving unit.

Over time, the front shelf trim can become cracked, discolored, or even break due to frequent cleaning, exposure to cold temperatures, or accidental damage. This can lead to a less secure shelf edge, which might not effectively prevent items from sliding off as intended.

Symptoms of a bad Front Shelf Trim include:

• Visible cracks or breaks in the trim
• Difficulty in fitting or staying attached to the shelf
• Aesthetic issues such as discoloration or warping
• Reduced effectiveness in preventing items from sliding off the shelf

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Glass Shelf Insert is an OEM part for Frigidaire refrigerators. This insert provides a sturdy and transparent surface for storing food items, allowing for easy organization and visibility within the refrigerator compartment. The glass measures approximately 23-3/4" wide and 16-5/16" deep.

Over time, the glass shelf insert can become damaged due to heavy loads, accidental impacts, or thermal stress from hot items. Causes of a bad glass shelf insert include cracks, chips, or complete breakage, which can compromise the safety and functionality of the shelf.

Symptoms of a bad glass shelf insert include:

• Visible cracks or chips in the glass
• Difficulty in maintaining a stable surface for food storage
• The shelf insert not fitting properly within the refrigerator due to damage
• Potential safety hazards from broken glass

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Rear Shelf Trim is an OEM part for Frigidaire refrigerators. It is designed to fit along the back edge of refrigerator shelves, providing a clean, finished look and helping to prevent items from sliding off the back of the shelf. 

Symptoms of a bad Rear Shelf Trim include:

• The trim becoming loose or detaching from the shelf, which can cause items to fall off more easily.
• Cracking or breaking of the trim, which may compromise the structural integrity of the shelf.
• Wear and discoloration that diminishes the aesthetic appearance of the refrigerator interior.

Causes of a bad rear shelf trim can include frequent removal or adjustment of shelves during cleaning or reorganization, physical impacts from storing or removing items, or the natural aging process that can make plastic components brittle over time.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Glass Shelf Insert is an OEM replacement part for Frigidaire refrigerators. It provides versatile storage space by allowing items to be viewed clearly and easily rearranged. This insert measures approximately  23.82 x 15.50 inches

Causes of a bad shelf insert may include cracks, chips or other damage due to repeated handling or excessive weight loads not suitable for glass. Normal wear over time can also affect the shelf surface.

Symptoms of issues include: 

• Visible damage detracting from shelf appearance and function
• Increased risk of items stored atop the shelf getting damaged 
• Difficulty cleaning due to cracks or irregular surfaces

This OEM replacement part is compatible with models by Electrolux, Kelvinator and Kenmore as well.

The Control Box Assembly is an OEM part for Frigidaire refrigerators. This complete assembly includes the electronic components and housing necessary to manage the refrigerator’s operations, such as temperature regulation, defrost cycles, and other vital functions.  

Causes of a bad control box assembly can include electrical surges, moisture damage, or normal wear and tear over time. Additionally, physical damage or faults in the wiring can lead to control box failure.

Symptoms of a bad control box assembly include:

• The refrigerator not cooling properly
• Error codes displayed on the control panel
• Inconsistent or fluctuating temperatures
• The refrigerator or freezer not defrosting as needed
• Unresponsive control buttons

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This refrigerator shelf spacer positions and supports a shelf so it sits secure and level. Replacing a worn or missing spacer helps eliminate wobble or shifting and restores proper fit and alignment inside the compartment. What it does

• Maintains correct spacing and alignment for the shelf
• Helps keep the shelf level and secure in its track or frame
• Replaces cracked, deformed, or missing spacers
• Symptoms can include a loose, tilted, or rattling shelf, or visible gaps where the shelf should seat

• One shelf spacer

• Disconnect power to the refrigerator before servicing
• Remove the shelf to access the spacer location
• Gently pry out the old spacer; avoid stressing plastic or glass components
• Press the new spacer firmly into place and reinstall the shelf, ensuring proper orientation

The Icemaker Kit is an OEM part for Frigidaire refrigerators. This kit includes everything needed to install or replace the icemaker in the freezer, ensuring a steady supply of ice.

Causes of a bad icemaker can include wear and tear over time, water line blockages, electrical failures, or mechanical issues within the icemaker components. Regular use and exposure to hard water can also contribute to the icemaker's decline.

Symptoms of a bad icemaker include:

• No ice production
• Low ice output
• Ice cubes that are smaller than usual or misshapen
• Leaks around the icemaker area

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Note: The icemaker used in this kit is 241798231 and the water valve is 242252603.