Parts for Frigidaire FPRU19F8WF5: System Parts

This condenser coil assembly removes heat from the refrigerant so the refrigerator can cool properly. It's a direct-fit replacement that restores the cooling loop's ability to shed heat and run more efficiently. What it does

• Exchanges heat from the refrigerant to the surrounding air so the cooling cycle can continue
• Helps the compressor run within normal temperature range
• Commonly replaced when the refrigerator is warm inside or the unit runs continuously
• Needed if the condenser is bent, clogged with debris, or leaking

• One condenser

• Disconnect power to the appliance before starting any repair
• Handle with care — coil fins and tubing can be sharp and easily damaged
• Reinstalling may require removal of back or lower access panels; keep fasteners organized
• Sealed-system work (cutting or brazing refrigerant lines) requires certified HVAC service — do not attempt if refrigerant lines must be opened

Secures wire harnesses and ground wires to your refrigerator cabinet. Replace if broken or missing to prevent wire damage. Verify fit with your model.

Fix a refrigerator that won't cool or runs constantly with this inverter compressor drive module. Controls variable-speed operation for efficient cooling.

This wiring harness routes power and signals between appliance components to restore reliable electrical connections and proper control operation. It replaces a worn or damaged connector assembly to help stop intermittent power or control failures. What it does

• Provides secure electrical connections between control, switches, and components
• Restores continuity when original wires or terminals are damaged or corroded
• Stops intermittent operation, control communication errors, or no-power symptoms
• Helps eliminate arcing or poor contact that can cause heat or burning smells

• One wiring harness assembly

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Confirm wire routing and connector orientation before disconnecting; photograph for reference
• Avoid pinching or stressing wires; secure harness with existing clips or ties

Fixes poor cooling and warm temps caused by moisture in the sealed system. This filter-drier protects the compressor during refrigerant repairs.

This support mounting bracket secures internal components and panels so your appliance stays stable and functions reliably. It replaces a worn or broken bracket to restore proper alignment and reduce rattling or loose parts. What it does:

• Provides a secure mounting point for internal panels or components
• Restores proper alignment to reduce vibration, noise, and movement
• Helps maintain structural stability of the appliance cabinet or assembly
• Works where a damaged or missing bracket causes loose or sagging parts

• One support mounting bracket

• Install using original fasteners; inspect adjacent parts for wear before reassembly
• Disconnect power and follow safety procedures before servicing the appliance
• If screws or clips are stripped or missing, replace them with matching hardware

Fix frost buildup and cooling issues with this defrost heater. Restores proper defrost cycles and eliminates excessive ice in your refrigerator or freezer.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Short hex washer head screw for chest freezers, upright freezers, and compact refrigerators. Replaces lost, stripped, or damaged screws to secure panels.

This wiring harness assembly routes electrical power and signals between components to restore reliable operation. It replaces damaged or worn wiring to help resolve control, power, or intermittent operation issues. What it does

• Provides factory-style electrical connections between controls, sensors, and motors
• Restores lost or intermittent power to affected components
• Replaces frayed, burned, or broken wires and connector ends
• Helps eliminate intermittent operation, failures to start, or unresponsive controls

• One wiring harness assembly

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock
• Compare new harness to the old unit before installation
• Route harness securely and fasten with existing clips or ties to prevent pinching or chafing

Protective cover assembly for chest freezers. Replaces cracked, broken, or missing covers to shield internal wiring and components while restoring appearance.

Replacement mounting screw secures panels, brackets, and trim inside refrigerators and freezers. Restores factory assembly when original fasteners are missing.

Refrigerator not cooling or freezing over? A failed evaporator fan motor stops air circulation. Straightforward DIY repair restores proper cooling.

Fix poor cooling or overheating issues. This condenser fan shroud assembly directs airflow across the condenser to restore cooling efficiency.

Mounting screw for refrigerators and freezers. Secures panels, brackets, and internal components. Replace when stripped, missing, or damaged.

This Power Supply Frame is an OEM part for Frigidaire refrigerators. It provides stability and support to the power supply components within the refrigerator.

Causes of a Bad Part: Exposure to moisture or physical damage can lead to corrosion or structural weakening of the frame. Continuous power fluctuations might also contribute to its deterioration.

Symptoms of a Bad Part:

• Loose or unstable power connections
• Corrosion or rust on the frame
• Power supply instability

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models

The PC Board is an OEM part for Frigidaire refrigerators. It controls and regulates various functions of the refrigerator, such as temperature settings, defrost cycles, and fan operation.

A bad PC Board can be caused by electrical issues, component failure, or damage due to power surges or mishandling. When the PC Board becomes faulty, it can result in issues such as inconsistent temperature control, improper defrosting, or failure of the refrigerator to operate at all.

Symptoms of a bad PC Board include:

• Inconsistent or inaccurate temperature control
• Failure to defrost properly, leading to ice buildup
• Unresponsive or malfunctioning control panel
• Failure of the refrigerator to power on or operate

Replace your faulty PC Board with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Fixes unresponsive controls, blank displays, or frozen settings. This electronic control board restores user commands and operation cycles in your appliance.

This baffle directs cold air inside the refrigerator to help maintain even temperatures and proper airflow. Replacing a damaged or missing baffle restores intended air circulation and helps performance. What it does

• Channels and directs airflow between compartments for more consistent cooling.
• Helps prevent warm spots caused by blocked or misdirected air.
• Reduces stress on the cooling system by restoring designed airflow paths.
• Commonly replaced when cracked, broken, or missing, or when airflow is visibly obstructed.

• Unplug the appliance or disconnect power before starting any work.
• Remove food, shelves, and drawers as needed for access; handle components gently to avoid damage.
• Inspect mounting points and gaskets; replace any damaged fasteners or seals.
• Refer to OEM instructions for model-specific removal/replacement steps.

This cover drain jumper is a molded drain-channel cover that helps route defrost and condensate water into the refrigerator drain system, preventing water from pooling inside the cabinet and reducing ice buildup. What it does:

• Guides defrost and condensate water into the drain channel so it flows to the drain pan
• Helps prevent water from pooling at the back or bottom of the fresh-food compartment
• Reduces the chance of ice forming around the evaporator or in the drain path
• Fits into the drain housing to maintain proper condensate flow

• Disconnect power to the appliance before beginning any service.
• Remove shelves/panels that obstruct access to the drain area; handle plastic parts gently to avoid breakage.
• Make sure the drain channel is clear of debris and ice before installing the cover for best results.

Replacement mounting screw for refrigerators and freezers. Secures panels, brackets, trim, and covers. Replace if missing, stripped, or damaged.

Harness cable tie secures and organizes wiring inside your appliance. Replace if damaged, cracked, or no longer holding wires firmly in place.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.