Parts for Frigidaire PLHS267ZCB2: 13 - System Parts

Reduces chlorine taste and odor while filtering sediment from your refrigerator's water and ice. Replace every 6 months for best performance. Verify fit.

Refrigerator not cooling properly? A damaged or clogged condenser coil prevents heat rejection, causing warm temps. This assembly restores efficient cooling.

Foam insulation block that surrounds the evaporator coil in your refrigerator. Replace if melted, cracked, or missing to maintain proper airflow.

Freezer not cooling below 32°F or water leaking under freezer? The drier filter removes moisture from the refrigerant system. Soldering required.

Fixes ice buildup in freezer and no cooling in fridge. This defrost heater kit melts frost from evaporator coils to restore airflow and temperature.

Refrigerator not cooling or freezing properly? A faulty evaporator coil may be causing warm temps and moisture buildup. Professional installation recommended.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Freezer icing up or fridge not cooling? This defrost thermostat kit fixes refrigerators that won't defrost properly. 10-minute DIY repair with video.

Rubber grommet that mounts and cushions the compressor to reduce vibration transfer. Replace if cracked, worn, or missing to restore quiet operation.

Secures the compressor to the mounting bracket in your refrigerator or freezer. Replace if missing, stripped, or corroded during compressor service.

Collects water from evaporator defrost cycles. Mounts near compressor under refrigerator. Replace if cracked, leaking, or damaged to prevent odors.

Refrigerator not cooling or running warm? This compressor kit restores proper cooling when the compressor fails. Professional installation recommended.

Compressor clicks and won't run? This start relay kit fixes refrigerators that won't cool. Common fix for clicking compressor that shuts off. Easy install.

Wire bale clip secures wiring harnesses and prevents loose connections in your refrigerator. Replace if damaged, broken, or missing to ensure proper wire routing. Confirm fit with your model number.

Black rubber mounting grommet that secures tubes and wires in your refrigerator. Replace if cracked, worn, or missing to properly hold components in place.

Secures panels, brackets, and assemblies in refrigerators and freezers. Replace missing, stripped, or damaged screws to restore proper fit and alignment.

Secures and protects wiring harness from strain damage. Replace if cracked, broken, or wires show wear. Verify fit with your model number listed.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Refrigerator not cooling or compressor won't start? A failed run capacitor prevents the compressor from running. DIY repair in 10-15 minutes with video guide.

Secures and organizes wiring harnesses in your refrigerator. Replace if broken, cracked, or wires are loose. Confirm fit with your model number.

Secures panels, brackets, and assemblies in refrigerators and freezers. Replace missing, stripped, or damaged screws to restore proper fit and alignment.

Support bracket that secures the condenser motor in place. Replace if bent, cracked, or broken to properly stabilize the motor assembly in your refrigerator.

Rubber grommet that cushions and secures bracket components inside your refrigerator. Replace if cracked, worn, or missing to restore proper support.

Defrost drain trough for side-by-side refrigerators. Channels water from the freezer evaporator to the drain tube. Replace if cracked or broken.

Secures the evaporator cover inside your refrigerator's freezer compartment. Replace this metal bracket if bent, broken, or missing to restore alignment.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Freezer drain tube that channels defrost water from the drain pan to the drip pan. Replace if cracked, leaking around the grommet, or causing floor leaks.

Refrigerator not cooling properly? This compressor tube connector links sealed system components. Professional installation required for refrigerant work.

Positions and secures condenser tubing to maintain proper spacing. Replace if worn, broken, or missing to prevent vibration, rattling, and tube damage.

Foam seal tape creates airtight barriers around refrigerator components. Replace when worn, compressed, or damaged to restore proper sealing and efficiency.

Refrigerator not cooling properly? This heat exchanger kit improves cooling efficiency in the sealed system. Moderate difficulty repair for side-by-side models.

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.