Need Help?
Call
Dishes not drying or staying wet after cycle? This heating element heats water for cleaning and air for drying. Most DIYers replace in under 30 minutes.
Turned off power to dishwasher. Removed front bottom cover of dishwasher and removed the wires going to each end of the heating element. unscrewed the two nuts holding the faulty heating element in place. Then removed bottmo dish rack and spinning washer arm from inside the dishwasher. Removed old heating element and replaced with new one. Installed in reverse order (tightened two nuts, connected wires, etc.). Turned power on as last step and was off and running...or should I say washing. Read more
Replacement water inlet hose for dishwashers. Connects water supply to the tub. Replace if cracked, leaking, or damaged by pests or wear.
Replaced hose Read more
Covers the gap beneath your dishwasher for a finished look. Replace if cracked, broken, or missing. Installs at base with screws (sold separately).
Easy job, I screwed the parts to the dishwasher Read more
Secures the lower spray arm to the filter assembly in your dishwasher. Replace if cracked, stripped, or missing to keep the spray arm stable during wash cycles.
The key was that information section that shows what model of dishwasher is compatible it was the only site I could find Read more
This is the cap that seals the rinse aid reservoir on the dishwasher door. It keeps rinse aid contained so it dispenses properly during the rinse cycle. Replace this cap if it is cracked, missing, or no longer seals tightly, which can cause rinse aid to leak out prematurely and result in spotty or poorly dried dishes.
Took cover completely off and tried putting back, could not match up left screw with available screw hole. Tried many different configurations and sequences to make this happen. watched a video on changing the front panel, the door in it had four screws, mine 2, no help there. Searched on the hyperextending issue, found an article about dogs and kids [had both here] climbing on the door and to check the springs and linkages. Linkages intact both sides, R [opposite] side spring very stretched.... Read more
Seals the rear of your dishwasher's circulation pump to prevent leaks. Replace if you notice water pooling or dripping from the motor area.
I first thought the leak came from the pump assembly rear o ring. I was wrong. The water was leaking from the pump. The pump assembly was shipped in 1 1/2 days with 2 more o rings. I lubed the o rings with dish soap, they slid in perfectly. reinstalled the clamp and screws and was ready to reinstall the dishwasher. Worked great. Next time I will buy the pump the first time. Buying the o rings separately adds $$. Read more
Noticeable wear, cracks, or deformation on the O-ring This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
If your dishwasher door won't latch or stay closed, the door strike may be broken or corroded. This repair takes about 15 minutes with basic tools.
Replaced the door strike Read more
Secures the kickplate toe panel at the bottom of your dishwasher. Replace if screw is stripped, missing, or damaged during kickplate removal or repairs.
Connects door springs to the dishwasher door hinge for smooth, balanced opening and closing. Replace if cracked, broken, or missing due to wear or damage.
This repair could have killed or maimed me -- really! Left door spring snapped. Online search, APP was only source with both door spring and linkage. Discovered link for APP repair-instruction video (not very well marked on parts page). This well-done video really helped build my confidence. Common sense told me to also replace unbroken spring and both linkages. Parts + shipping = $75 -- wow, that hurt. Surprised how fast the parts shipped & arrived by ground! This is going to be easy! ... Read more
Dishwasher not heating or drying dishes? This high limit thermostat monitors water temperature and prevents overheating. Easy DIY fix with basic tools.
I took and ohm meter to the heating element and figured out that was ok. Went to the thermostat and it was toast. Easy fix. Read more
This metal mounting bracket secures the circulation pump motor inside the dishwasher. It holds the pump assembly firmly in place to prevent vibration and ensure proper alignment with the wash system. Replace this bracket if it is cracked, bent, or corroded, which can cause excessive noise, vibration, or misalignment of the pump during wash cycles.
Bought combination set Motor & pump/ pump assembly plus new thermostat/ bracket. Exchanging motor and pump took about 15-30 min. Getting the dishwasher out and back took at least 30 min plus each way. Online video helped a great deal Read more
Door won't stay closed or latch? This dishwasher door latch assembly restores secure closing and proper door recognition. Easy 10-minute DIY fix.
I always come to Appliance Parts Pros for my parts. Ordered the handle, and it arrived in a few days. Took me all of 10 minutes to replace the worn part. Even picked up a new tub gasket while I was at on here. That has made the washer a lot less noisy. I recommend these guys to anyone who is even a novice DIYer. Read more
Seals the connection between the dishwasher tub and sump assembly. Replace if water leaks from the base or the gasket appears cracked or flattened.
Following the great video on the site, I pulled the motor off and was about to put the o-rings on when I noticed there was rust on the motor shaft. Very close inspection showed the o-rings were still good. Not having time to order a motor, and a local store was having a sale, I replaced the whole unit. Read more
Set of 8 screws and washers.
Dishwasher worked fine except the top rack would keep coming off the rails, could see the rollers needed replacement. Washer is 10 years old, and in that time the rollers had become brittle and broken. At first tried to use old screw and washer, but washer was impossible to remove from screw as I have hard water and the calcium deposits seemingly cemented it. Order this screw and washer set and within 5 minutes of getting easily replaced the old rollers. The video was very helpful, as was the... Read more
Plastic stop cap that secures the upper dishrack rail track in your dishwasher. Replace if broken, cracked, or missing to keep rack sliding smoothly.
Self-replaced Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.