Parts for Ge GTW845CSN0WS: Top Panel & Lid Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Washer won't fill or overfills? This water level sensor detects water height and signals the control board. Moderate DIY repair on top-load washers.

Fixes electrical safety issues and grounding problems in dryers. This ground screw secures the ground wire to the chassis for safe discharge. Easy install.

Replace your washer's top cover panel if cracked, rusted, or damaged. This metal enclosure covers internal components and provides a finished look.

Washer not heating water correctly or wonky water temperature? The thermistor monitors water temp during cycles. Common DIY fix, takes about 30 minutes.

Leveling leg for top-load washers. Installs at the base to stabilize the unit and adjust height. Replace if cracked, broken, or missing to restore balance.

Replace your washer lid corner bumper to restore quiet, smooth closing and prevent noise and wear. This cushioning bumper dampens impact at the lid's front corner.

Center lid bumper cushions and aligns your washer lid to reduce noise and prevent metal contact. Replace when worn or missing for quieter closing.

Washer won't start or lid won't lock? The lid lever arm ensures your washer lid locks securely during cycles. Common fix for lid lock failures.

A replacement funnel bezel for the dispenser that restores the dispenser opening and helps guide water or ice into your cup with a finished look. Fits the dispenser area to repair cosmetic damage or broken trim. What it does:

• Replaces cracked, broken or missing dispenser trim that can catch drips and obstruct dispensing
• Guides water and ice into the cup to reduce splashing and misalignment
• Restores the original appearance of the dispenser opening
• Works with the dispenser assembly to help maintain proper user access

• Disconnect power to the appliance before servicing to reduce shock risk
• Usually installs from the front of the dispenser; remove adjacent trim or liners if needed for access
• Handle gently to avoid scratching the finish and align snaps or tabs before pressing into place

Washer won't start or spin? Lid lock light stays off or cycles? This lid lock service kit restores proper lid locking. Video guide included.

Glass lid frame assembly for top-load washers. Replace if your see-through lid is cracked, broken, or damaged. Installs at the top of the washer cabinet.

Washer won't start or spin? Lid lock light stays off or cycles? This lid lock service kit restores proper lid locking. Video guide included.

Fix cracked or missing dispenser trim with this washer dispenser lid bezel. Restores finished appearance and protects internal components from damage.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Fix detergent not dispensing or leaking with this washer smart dispense box. Houses dispenser components and directs detergent flow properly.

Fixes standing liquid or residue in dispenser cup. This siphon cap creates proper vacuum action to empty additive compartments during rinse cycle.

Softener not dispensing or drawer overflowing? This washer fabric softener dispenser drawer holds and releases softener during the wash cycle. Simple fix.

Replacement lid hinge for washers. Mounts the washer lid and provides smooth open/close movement. Order if your hinge is bent, cracked, or broken.

A single replacement screw used to secure the lid hinge on top-load washers. Replaces a worn or missing hinge fastener so the lid stays aligned and operates smoothly. What it does

• Secures the lid hinge assembly to the washer cabinet or lid
• Restores proper lid alignment and reduces wobble or sagging
• Helps stop the lid from shifting, binding, or making noise when opened/closed
• Used when original screw is missing, stripped, or damaged

• One lid hinge screw

• Disconnect power and water supply before working on the washer
• Support the lid and hinge assembly while removing and installing the screw to prevent injury or damage
• Use the correct screwdriver or bit to avoid stripping the screw head

Fix a washer that won't start or has a blinking lid lock light with this lid lock wiring harness. Connects the lid lock to the control board. Easy DIY fix.

Loose control panel or rattling cabinet? This 10-32 machine screw secures panels, brackets, and components in your top-load washer. Simple install.

Washer won't start or lid lock fails? This harness clip secures the lid lock wiring to prevent chafing and intermittent connection issues. Quick fix.

Self-tapping hex washer head screw for securing washer panels and brackets. Replace missing, stripped, or damaged mounting screws for secure assembly.

The Water Inlet Valve Seal is an OEM part for GE washing machines, designed to ensure a watertight seal around the water inlet valve. This part helps prevent leaks by sealing the connection between the water inlet valve and the washing machine's internal tubing. 

Causes of a bad water inlet valve seal include normal wear and tear, exposure to hard water minerals that can erode the seal, and improper installation that may strain or damage the seal.

Symptoms of a bad Water Inlet Valve Seal include:

• Water leaking from the back or underside of the washing machine
• Visible signs of wear or damage to the seal
• Unexplained increase in water usage or utility bills, which may indicate a slow leak

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Fix water continuously dripping into your washer tub with a new water inlet valve. Common cause when washer leaks between cycles. DIY repair in 1 hour.

Fix washer water valve connection issues with this wire harness. Restores electrical power to the water inlet valve for proper fill cycles.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.