Parts for Ge GTW845CSN0WS: Tub & Motor Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This harness wire tie secures and organizes the appliance's wiring harness. Replacing a damaged or missing tie keeps wires properly routed and protected to help prevent chafing, disconnections, and vibration noise for more reliable operation. What it does:

• Bundles and anchors wiring harnesses along the intended routing path
• Helps prevent wire insulation from rubbing, pinching, or wearing through
• Reduces rattling or vibration noise from loose wires
• Common signs include a broken/missing tie, dangling wires, or visible wear on the harness

• 1 harness wire tie

• Disconnect power before servicing; allow any moving parts to stop
• Note original wire routing and mounting location; take a photo for reference
• Install the new tie at the same point and snug it just enough to secure without crushing wires; trim excess strap
• Verify wires are clear of moving or hot components before restoring power

The Pressure Hose Assembly is an OEM component specially designed for GE top-load washing machines. It provides pressurized water transport from the water inlet valve to the machine components that require it. 

Located internally behind the washer casing, this tough braided hose reliably conveys water from the home supply plumbing. Its reinforced construction prevents kinks that could obstruct flow to critical parts like the dispenser drawer and pump chamber. 

Causes related to hose failure center around splits or cracks developing due to stress from repeated machine-generated pressure pulses over 10+ years.

Symptoms of a bad pressure hose include: 

• Reduced or inconsistent water levels during cycles   
• Water leaking/dripping inside unit from hosed areas
• Noticeable splits or cracks visible in braided casing

Replacing with this authentic GE OEM hose restores optimized water transmission. Proper flow supports thorough cleaning for washer units like Hotpoint, RCA, or Kenmore top-loaders.

This left-side connector bracket secures a wiring connector or harness to the appliance frame, keeping electrical connections stable and reducing strain on terminals for reliable operation and easier component access. What it does:

• Holds and positions a wiring connector or harness on the left side of the appliance
• Prevents connector movement that can cause intermittent electrical contact or wiring stress
• Keeps terminals aligned for easier reconnection during service or part replacement
• Helps protect connectors from vibration and accidental disconnection

• Disconnect power to the appliance before beginning any repair.
• Remove any panels or components necessary to access the existing bracket; basic hand tools are typically required.
• Transfer the wiring connector into the new bracket without forcing; ensure secure seating and proper alignment.
• Inspect surrounding wiring and terminals for damage and replace or repair as needed.

This right-side connector bracket supports and secures an electrical or wiring connector assembly to the appliance chassis, restoring proper connection alignment and reducing strain on wiring. Fits the original mounting location and shape. What it does:

• Holds the appliance electrical connector in the correct position to prevent loose or strained wiring
• Maintains secure contact for reliable power or signal transfer
• Prevents connector movement that can cause intermittent operation or arcing
• Replaces a cracked, broken, or missing bracket that no longer secures the connector

• One right-side connector bracket

• High-level replacement only; bracket orientation should be confirmed before tightening fasteners
• Use proper-size fasteners and do not overtighten to avoid cracking the part
• Disconnect power to the appliance before starting any repair to avoid shock or damage
• If wiring or connectors are damaged, replace or repair those components per manufacturer instructions

The Agitator Base Hybrid Assembly is an OEM part for GE washing machines. This part serves as the foundation for the agitator, playing a crucial role in the effective movement and agitation of clothes during the wash cycle. 

Common causes for replacing the agitator base hybrid assembly include physical damage, such as cracks or breaks, which can occur from overloading the washer or from foreign objects getting caught during the cycle.
 
Symptoms of a bad agitator base hybrid assembly include:

• The agitator not moving correctly or at all during the wash cycle
• Unusual noises coming from the agitator area during operation
• Clothes not being cleaned thoroughly due to insufficient agitation
• The washing machine vibrating more than usual due to an unbalanced agitator

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Auger is an OEM part for GE washing machines. It is responsible for agitating and moving the clothes during the wash cycle. The auger is designed to create a gentle and thorough wash by creating a swirling motion that helps to remove dirt and stains from the garments. It ensures that your clothes are properly cleaned and evenly distributed throughout the wash.

Causes of a bad auger can include wear and tear over time, exposure to heavy loads or unbalanced loads that put excessive strain on the auger, or damage due to foreign objects getting stuck or tangled in the mechanism.

Symptoms of a bad auger include:

• Clothes not being properly cleaned.
• Excessive noise or vibration during the wash cycle.
• Inability to agitate or move the clothes effectively.
• Visible damage or wear on the auger.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Washing Machine Screw is an OEM replacement part for GE washing machines. This screw is used to secure various components within the washing machine, such as the drum, control panel, or housing. While it may seem like a small part, the screw plays an important role in maintaining the structural integrity of the machine.

Causes for a bad or missing screw can include corrosion, loosening due to vibrations during wash cycles, or it may simply be missing due to repairs or disassembly.

Symptoms of a bad or missing Washing Machine Screw include:

• Unusual noises coming from the machine
• Components appearing loose or misaligned
• Increased vibrations during operation

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is the short agitator cap for select top-load washers. It covers the top of the agitator to keep water and debris out of the agitator hub, preserving proper wash action and a clean appearance.

• Seals the agitator opening to prevent moisture and detergent buildup inside the agitator
• Helps maintain correct agitation by keeping the hub area protected
• Common signs it's needed: missing or loose cap, cracked or warped cap, water or residue collecting inside the agitator

• Unplug the washer before servicing
• Pull the old cap straight up to remove; some may require gentle prying
• Press the new cap firmly into place until fully seated
• Inspect the agitator hub for debris and clean before installing the new cap

The Washer Hub is an OEM replacement part for GE washing machines. It is a central component located inside the washing machine basket that the inner tub, drive motor, and suspension springs connect to. The washer hub rotates the washing basket during agitation and spinning cycles to clean clothes thoroughly.

Constant rotational motion and vibration placed on the hub can potentially cause cracks or weakness over an extended time. Improper load balancing causing excessive shaking may also damage the hub.

Symptoms of a bad washer hub include: 

• The washing machine basket fails to spin or agitate properly
• Loud grinding or clicking noises coming from inside the machine  
• Vibrations felt through the cabinets or floor during cycles
• Misalignment or wobbling of the inner washing tub

This OEM GE replacement part is compatible with some Hotpoint, RCA, and Kenmore.

The Hub Nut Washer is an OEM part for GE washing machines. It functions to secure the hub and ensure that the drum remains properly aligned during wash and spin cycles, contributing to the smooth operation of the washing machine.

Causes of a bad hub nut washer can include wear and tear over time, excessive vibration or movement, or exposure to harsh detergents. A damaged or worn-out hub nut washer can lead to issues with the drum's stability, affecting the overall performance of the washing machine.

Symptoms of a bad Hub Nut Washer include:

• Excessive noise or vibration during wash cycles
• The drum not spinning correctly or being misaligned
• Leaks around the drum area
• Loose or wobbly drum

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Hub nut is an OEM part for GE washing machines, designed to securely fasten the tub assembly to the drive system of the washer. This component is crucial for the stability and operation of the washing machine's drum, ensuring that it remains properly aligned and attached during the vigorous motion of the wash cycles.

Per the manufacturer due to the high torgue on the hub nut an impact wrench should be used to remove and replace the hub nut. It also rquires a 90 ft lb torque limiting extension WX05X10028 and a 1 5/16th impact socket WX05X10022. You can order these through the links or use ones you already have. WARNING: The 90 ft lb torque limiting extension must be used when removing or installing the hub nut to prevent damage to the hub nut and transmission due to over torquing with the impact wrench. 

Causes of these issues can range from natural wear and tear over time to improper installation or overloading of the washer, which can exert undue stress on the Nut Hub and other related components. Ensuring that the Nut Hub is in good condition and properly tightened is essential for the longevity and proper function of your GE washing machine.

Symptoms of a faulty Hub nut include:

• Unusual noises during the spin cycle, indicating that the drum may be loose or off-balance
• The washing machine's drum exhibiting excessive movement or vibration beyond normal levels
• Water leaks from the area surrounding the drum

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This screw is a factory fastener used to secure appliance components. Replace a missing, stripped, or corroded screw to keep panels, brackets, and assemblies tight and help prevent vibration or rattling from loose hardware.

• Secures panels, brackets, and internal assemblies at their mounting points
• Replaces lost, rusted, or stripped hardware for a solid, reliable hold
• Helps reduce vibration, rattling, or shifting caused by loose fasteners
• 1/4-20 thread per OEM designation for proper fit where specified

• Disconnect power and, if applicable, shut off water supply before servicing
• Start threads by hand to avoid cross-threading, especially in plastic
• Tighten snugly; do not overtighten to prevent stripping or cracking
• Verify alignment and stability of the secured component after installation

The Platform Transmission Assembly Kit is an OEM part for GE washers. As the central mechanical linkage, this assembly connects the transmission gears to the rotor motor shaft. 

The platform trans kit includes the transmission gears, belt, mounting hardware, and flexible coupler which transfers rotary motion from the motor to the wash basket drum. During agitation, it coordinates oscillating movement. For spin, it facilitates high-rpm extraction via a series of spinning planetary gear reductions.

Symptoms of a bad platform trans kit include:

• Erratic or no agitation movement  
• Failure to achieve proper spin speeds
• Grinding noises and vibrations during the operation
• Belt slipping off tracks or shredding

This genuine GE OEM part also fits Hotpoint, RCA, and select Kenmore units for years of reliable performance.

This suspension spring supports the washer tub, helping keep the drum centered and reducing vibration for smoother cycles. Replaces a worn or broken tub-support spring to help restore stable, quiet operation. What it does:

• Holds and stabilizes the inner tub during spin and agitation
• Helps prevent excessive vibration, rocking or banging
• Keeps the drum aligned so loads spin more evenly
• Worn or broken springs can cause noisy operation or a shifting tub

• One suspension (tub support) spring

• Disconnect power and water before beginning any repair
• Support the tub or cabinet before removing old spring(s) to prevent sudden movement
• Inspect related suspension components and replace any other damaged springs or mounts

A small mounting support that provides a stable anchor point for screws used to secure panels or internal assemblies. Replacing a damaged screw platform restores proper fastener engagement and reduces panel movement and vibration. What it does:

• Anchors screws to hold trim, panels or internal components in place
• Restores secure attachment when the original mounting point is cracked or worn
• Helps eliminate rattling, loose panels, or alignment issues caused by a failed mounting surface
• Works with the appliance's existing screws and surrounding hardware to maintain structural fit

• Disconnect power to the appliance before attempting any repair
• Use the correct screws and a properly sized screwdriver to avoid further damage
• Inspect surrounding mounting points and replace any stripped screws or damaged clips as needed

The Mode Shifter is an OEM component specifically designed for GE washing machines. It contains the internal gears and linkage mechanisms that shift the transmission between spin, agitate, and drain functions depending on the selected wash cycle settings. 

Symptoms of a bad mode shifter include:

• Abnormally loud grinding noises coming from inside the washer
• Inability to advance fully through cycles or change functions  
• Excessive vibration felt in the washer or surrounding cabinetry
• Poor cleaning performance from ineffective agitation 

Causes of mode shifter malfunction involve worn gears, damaged or loosened internal components, or blockages preventing smooth operation over extended use.

This OEM GE replacement part is also compatible with some Hotpoint, RCA, and Kenmore models. Reliable transmission shifting promotes optimized washing performance. 

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Clutch is an OEM component specifically designed for GE washers. Located between the motor and transmission, this assembly controls the engagement and disengagement of rotational movement. 

During agitation, the clutch allows motor power to pass through to the transmission, facilitating oscillating drum movement. Then for spin cycles, it engages a gear mechanism that multiplies RPMs providing high-speed extraction. Precise clutch actuation ensures smooth transitions between wash and spin functions. 

Symptoms of a bad clutch include: 

• Excessive vibration and clunking noises  
• Failure to agitate or inability to engage high spin speeds
• Drum doesn't oscillate/switch properly between movements  
• Premature wear on transmission/gears from improper clutch release

Replace yours with this authentic GE part to restore smooth cycle changes. You'll feel optimized performance and extended component life. This OEM replacement is also suitable for Hotpoint, RCA, and select Kenmore washers.

The Clutch Spring is an OEM part for GE washing machines. The spring allows the clutch to engage and disengage with the spin mechanism, facilitating the transition between the wash and spin cycles. 

Over time, the Clutch Spring can wear out or become damaged, affecting the washer's ability to switch between cycles smoothly. 

Symptoms of a bad Clutch Spring include:

• The washing machine not spinning or spinning inadequately
• Clothes remaining wetter than usual after the spin cycle
• The washer making unusual noises during the spin cycle
• The machine struggling to transition between washing and spinning phases

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This GE Ball Joint Upper is an OEM part for GE washing machines. Designed to ensure smooth and stable movement of the washing drum, this ball joint plays a crucial role in the appliance's suspension system. 

A compromised ball joint can lead to a decline in the performance of the washing machine, making it essential to address the issue promptly.

Symptoms of a bad Ball Joint Upper include:

• Unusual noises during operation, especially during the spin cycle.
• The drum may seem to wobble or be off-balance.
• Excessive vibration of the machine, more than usual.
• Uneven wear of other suspension parts, leading to further maintenance issues.
• Potential leakage or damage to surrounding components due to misalignment.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This service kit provides lubricant for the washer's suspension ball joint. Proper lubrication reduces friction so the tub support moves freely and may help quiet squeaks or creaks from dry ball-and-socket joints during wash or spin. What it does:

• Lubricates the suspension ball-and-socket joint to reduce friction and wear
• May help address squeaking or creaking noises from the suspension area
• Supports smoother tub movement and vibration control
• Useful after suspension service or when joints appear dry

• Grease for lubricating the suspension ball joint

• Unplug the washer and shut off water supply before servicing
• Access the suspension ball joint; clean old grease and debris from mating surfaces
• Apply a thin, even coat to the ball and socket; avoid over-application and keep grease off belts, pulleys, or braking surfaces
• Reassemble and run a short test cycle to verify normal operation

A general-purpose appliance grease used to lubricate moving parts and reduce friction for smoother operation. Helps protect metal components from wear and keeps mechanisms operating quietly and reliably. What it does:

• Lubricates gears, hinges, rollers and other moving parts to reduce friction and wear
• Helps stop or reduce squeaks, grinding noises and stiff or sticking movement
• Aids smooth operation of controls and mechanical linkages
• Provides light protection against corrosion on contact surfaces

• Disconnect power before servicing the appliance to avoid shock or injury
• Clean and dry the area to be lubricated; apply a light, even amount where parts make contact
• Avoid getting grease on electrical components, heating elements, or surfaces that require friction
• Wipe away excess lubricant and test operation before returning the appliance to regular use

The Motor Rotor is an OEM part for GE washers. This part is responsible for driving the rotation of the washer drum, allowing for the agitation and spinning cycles. The motor rotor works with the washer motor to generate the necessary rotational force, ensuring that your laundry is thoroughly cleaned and properly dried.

A bad motor rotor can occur due to wear and tear, mechanical failure, or electrical issues. If you notice symptoms such as the drum not spinning or agitating, unusual noises during operation, or error codes indicating a faulty rotor, it may be time to replace the component.

Symptoms of a bad motor rotor include:

• Drum not spinning or agitating
• Unusual noises during operation
• Error codes indicating a faulty rotor

Restore your GE washer by replacing the faulty motor rotor with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Accelerometer is an OEM part for GE washers. It monitors vibration levels during cycles to ensure the tub is agitating or spinning as expected. Precise feedback allows the control board to make real-time adjustments or stop operation if an irregular vibration or shaking occurs.

Causes of a bad accelerometer can be normal wear over time, moisture or temperature damage to sensitive electronic components, or physical deformation from heavy impact. 

Symptoms include:

• Cycles failing to advance properly through agitate or spin phases  
• Excess noise or vibrating issues during washing
• Fault codes related to tub operation
• Sensitivity issues recognizing different load levels

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. Replacing a faulty accelerometer helps maintain smooth, balanced operation.

The Stator & Speed Sensor w/ Harness is an OEM part for GE washers. This assembly includes the stator, speed sensor, and wiring harness that connects the two components.  

The stator is the stationary outer portion of the washing machine motor that generates electromagnetic pulses to power the spinning rotor. The speed sensor detects the rotor's rotational speed and relays this data to the control board via the wiring harness. This allows the board to monitor drum movement and accurately control cycle times based on RPM.

Symptoms of a bad stator & sensor assembly include:  

• Inability to sense or achieve proper spin speeds   
• Motor “humming” but not spinning fully
• Control board errors/cycles not finishing as programmed
• Electrical burning smells during high-load spins

This OEM stator & sensor assembly is also compatible with Hotpoint, RCA, and select Kenmore washers.

This speed sensor monitors drum/motor rotation and helps the appliance detect and regulate spin speed for proper cycle operation. Replacing a worn sensor restores accurate speed feedback for reliable performance. What it does

• Detects rotation speed and sends a signal to the control board so the machine can manage cycle timing and motor control
• Commonly replaces a failed sensor that causes intermittent or no spin, stalled cycles, or incorrect cycle behavior
• Helps resolve speed-related faults or inconsistent operation tied to sensor feedback
• Interfaces with the motor/drive assembly via a wiring harness — no separate calibration on most models

• One speed sensor

• Disconnect power (and gas if applicable) before servicing to avoid shock or injury
• Access typically requires removing the access panel or cabinet; avoid sharp sheet-metal edges and keep track of fasteners
• Unplug the sensor wiring harness before removing the old sensor; install the new sensor in the same orientation and secure all fasteners

The Drain Pump Seal is an OEM part for GE washing machines. This seal ensures a watertight connection between the drain pump and the washer tub, preventing leaks during the draining process. It plays a critical role in maintaining the efficiency and cleanliness of the wash cycle by keeping water contained within the system.

Causes of a bad drain pump seal can include wear and tear from regular use, degradation due to exposure to harsh detergents or chemicals, or physical damage such as cracks or tears. A compromised seal can lead to water leakage and potentially damage other components of the washing machine.

Symptoms of a bad drain pump seal include:

• Water leaking from the bottom of the washer
• Unusual noises during the draining cycle
• The washer not draining properly
• Visible cracks or damage to the seal

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Drain Pump is an OEM part for GE washing machines. It's engineered to remove the used water from the washer at the end of each cycle, ensuring the machine is properly emptied and ready for the next load. This component is responsible for the circulation and expulsion of water, playing a vital role in the washing machine's ability to clean clothes thoroughly.

Causes of a bad Drain Pump can include obstructions within the pump itself, such as small garments or debris that can block water flow, or mechanical failures like a burnt-out motor or damaged impeller blades. 

Symptoms of a bad Drain Pump include:

• Water remaining in the drum after the wash cycle has completed.
• The washing machine failing to start due to sensing water from a previous cycle.
• Unusual noises coming from the pump area

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Internal Drain Hose Asm is an OEM part for GE washers. It is the hose located inside the washer that channels drained water from the tub out to the external drain system. 

Proper drainage is essential for washer operation. Causes of a bad internal hose can include cracks, kinks, or holes developing over time, especially in hoses made of brittle plastic material. Mineral buildup can also obstruct flow.  

Symptoms of a bad Internal Drain Hose Asm include:

• Puddling or pooling of water inside the washer tub after cycles
• Water not fully draining or draining slowly from the tub  
• Leaks or wet surroundings near the back of the washer

This GE replacement hose ensures your washer continues draining efficiently. This is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a self-tapping Plastite screw with a hex washer head and a 5/8 in. length that secures plastic and thin-sheet components. Use it to replace missing or damaged mounting screws for a snug, reliable fit. What it does:

• Forms threads in plastic (Plastite style) to fasten panels, brackets, and trims.
• Hex washer head provides a larger bearing surface for better holding power.
• Replaces stripped, corroded, or missing screws to stop loose or rattling parts.
• Works where a self-tapping screw is required for secure mounting without a separate nut.

• Use the correct hex/nut driver and a properly fitting bit to avoid stripping the head.
• Hand-start the screw and drive straight to prevent cross-threading; stop when snug—do not overtighten into plastic.
• Unplug the appliance or shut off power before disassembling or working near electrical components.
• Replace with the same screw type and size to maintain proper fit and function.

The Clamp is an OEM part for GE washers. It is used to securely fasten critical components like hoses, sensors, and wiring harnesses in place inside the washer cabinet. 

As a machine that handles water, chemicals, and moving parts, a washer requires many clamps to organize its internal systems. They ensure hoses and electrical wiring remain properly positioned and protected throughout years of operation. Without solid clamps, connections could loosen or detach, leading to leaks or electrical faults.

Causes of a bad clamp can include fatigue from constant vibration, outright breakage from impact or tension overload, or rust/corrosion damage over extended use. 

Symptoms of a failed clamp include:

• Loose, disconnected or damaged hoses and wiring  
• Water leaks from hose connections
• Electrical or sensor errors

The clamp is also compatible with some Kenmore and other brands that use GE components.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.