Parts for Kenmore 417.97804792 (41797804792, 417 97804792): Transmission Parts

The Agitator Hub is an OEM part for Frigidaire washing machines. It connects the agitator to the drive shaft, enabling the agitator to rotate and move clothes effectively during the wash cycle.  

Causes of a bad agitator hub can include wear and tear from frequent use, exposure to harsh detergents or hard water, or damage from overloading the washer.  

Symptoms of a bad agitator hub include:

• Agitator not moving or rotating properly
• Loud noises or grinding sounds during the wash cycle
• Clothes not being cleaned effectively
• The washer shaking or vibrating excessively

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This gear assembly transfers power from your washer's motor to the agitator and spin basket. It controls the different motions needed for washing and spinning cycles. Replace it if your washer agitator doesn't move, makes loud grinding noises, or fails to spin clothes dry.

This is a rubber lip seal that fits around the upper portion of the washer's basket drive tube, preventing water from leaking past the shaft and into the transmission or bearings below. It creates a watertight barrier between the wash tub and the drive mechanism. Replace this seal if you notice water leaking from beneath the washer tub, hear grinding noises during the spin cycle, or find oil residue under the machine.

A replacement hex washer head screw that secures appliance panels and components. Durable hardware designed to match OEM fit so you can restore proper fastening and reduce rattling or loose parts. What it does:

• Fastens panels, brackets, and assemblies where a 1/4-20 thread is specified
• Provides a built-in washer head to distribute load and resist pull-through
• Commonly used where vibration or movement can loosen standard screws
• Helps stop rattling, misalignment, or loose trim caused by missing or stripped fasteners

• Use the correct screwdriver or socket to avoid stripping the head; tighten until snug, do not over-torque
• Replace any damaged mating hardware or worn threads for a secure fit

This is a rubber seal gasket that fits between the transmission gear case housing halves on a washing machine. It prevents gear oil from leaking out of the transmission assembly during operation. Replace this gasket if you notice oil leaking from the bottom of the washer or if the transmission is being disassembled for repair.

Agitator rod and gear kit for washers. Connects the agitator to the drive system. Replace if gears are stripped, worn, or rod is broken or damaged.

Suspension spring for washer drum support system. Replaces worn, stretched, or broken springs that no longer properly suspend the tub assembly.

The Tub Seal is an OEM part for Frigidaire washing machines. It is designed to create a water-tight seal between the washing machine tub and the transmission or drive system. This seal prevents water from leaking out during the operation of the washer and protects the mechanical components from water damage.

Symptoms of a failing tub seal include:

• Water leaking from the underside of the washing machine.
• Increased moisture or puddles forming under the machine during use.
• A musty or moldy smell, indicating that water has been seeping and not properly drying.

Causes of a bad tub seal can include aging and wear over time, exposure to harsh detergents that degrade the material of the seal, or mechanical stress from unbalanced loads that can cause the seal to fail. It's important to address these issues promptly to prevent further damage to the washing machine.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Installation instructions manual for washer dryer combo units. Provides step-by-step setup guidance. Replace if lost, damaged, or illegible.

This printed owner's guide provides clear operating instructions, safety information, and basic care tips so you can use and maintain your appliance with confidence. What it does:

• Explains control panel functions and normal operating steps
• Lists safety precautions and recommended maintenance tasks
• Provides basic troubleshooting guidance for common user issues (controls, noises, or performance questions)
• Offers setup and operating tips to extend appliance life and avoid misuse

• Store the guide with your appliance paperwork for easy reference.
• Follow safety warnings exactly; disconnect power before servicing.

Snap-in bushing for washer assemblies. Replaces worn, cracked, or missing bushings that provide cushioning and support in internal components.

Harness cable tie secures and organizes wiring inside your appliance. Replace if damaged, cracked, or no longer holding wires firmly in place.

Secures the backsheet to the cabinet, preventing panel gaps and rattling. Replace if clip is broken or panels are loose. Confirm fit with your model number.

This component adjusts the tension of washer suspension springs in laundry center units and is located within the suspension system. Replace when experiencing excessive vibration, unbalanced loads, or unusual movement during spin cycles.