Parts for Kenmore 417.99570100 (41799570100, 417 99570100): Transmission Parts

The Agitator Hub is an OEM part for Frigidaire washing machines. It connects the agitator to the drive shaft, enabling the agitator to rotate and move clothes effectively during the wash cycle.  

Causes of a bad agitator hub can include wear and tear from frequent use, exposure to harsh detergents or hard water, or damage from overloading the washer.  

Symptoms of a bad agitator hub include:

• Agitator not moving or rotating properly
• Loud noises or grinding sounds during the wash cycle
• Clothes not being cleaned effectively
• The washer shaking or vibrating excessively

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is a rubber lip seal that fits around the upper portion of the washer's basket drive tube, preventing water from leaking past the shaft and into the transmission or bearings below. It creates a watertight barrier between the wash tub and the drive mechanism. Replace this seal if you notice water leaking from beneath the washer tub, hear grinding noises during the spin cycle, or find oil residue under the machine.

A replacement hex washer head screw that secures appliance panels and components. Durable hardware designed to match OEM fit so you can restore proper fastening and reduce rattling or loose parts. What it does:

• Fastens panels, brackets, and assemblies where a 1/4-20 thread is specified
• Provides a built-in washer head to distribute load and resist pull-through
• Commonly used where vibration or movement can loosen standard screws
• Helps stop rattling, misalignment, or loose trim caused by missing or stripped fasteners

• Use the correct screwdriver or socket to avoid stripping the head; tighten until snug, do not over-torque
• Replace any damaged mating hardware or worn threads for a secure fit

This is a rubber seal gasket that fits between the transmission gear case housing halves on a washing machine. It prevents gear oil from leaking out of the transmission assembly during operation. Replace this gasket if you notice oil leaking from the bottom of the washer or if the transmission is being disassembled for repair.

Agitator rod and gear kit for washers. Connects the agitator to the drive system. Replace if gears are stripped, worn, or rod is broken or damaged.

Suspension spring for washer drum support system. Replaces worn, stretched, or broken springs that no longer properly suspend the tub assembly.

Replace the control panel housing cover on your washer or washer dryer combo. Needed when the original housing is cracked, broken, or damaged.

The Tub Seal is an OEM part for Frigidaire washing machines. It is designed to create a water-tight seal between the washing machine tub and the transmission or drive system. This seal prevents water from leaking out during the operation of the washer and protects the mechanical components from water damage.

Symptoms of a failing tub seal include:

• Water leaking from the underside of the washing machine.
• Increased moisture or puddles forming under the machine during use.
• A musty or moldy smell, indicating that water has been seeping and not properly drying.

Causes of a bad tub seal can include aging and wear over time, exposure to harsh detergents that degrade the material of the seal, or mechanical stress from unbalanced loads that can cause the seal to fail. It's important to address these issues promptly to prevent further damage to the washing machine.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Dryer not heating? This heating element produces hot air to dry clothes. Common DIY repair takes 1-2 hours with basic tools. Fixes no-heat issues.

Ceramic dryer heating element terminal block.

Ceramic dryer heating element housing insulator.

Snap-in bushing for washer assemblies. Replaces worn, cracked, or missing bushings that provide cushioning and support in internal components.

Secures the drain hose to prevent leaks and disconnection during spin cycles. Replace if cracked, loose, or causing water leakage. Verify fit with your model.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

This component adjusts the tension of washer suspension springs in laundry center units and is located within the suspension system. Replace when experiencing excessive vibration, unbalanced loads, or unusual movement during spin cycles.

Red adhesive strip for washers. Secures components and panels inside the cabinet. Replace if peeling, missing, or no longer holding parts in place.

This part has been discontinued by the manufacturer and is no longer available.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.