Trimmer

Replace your string trimmer's worn gearbox spacer to restore proper gear alignment and reduce excessive vibration. Essential fastening component.

Cutting head not rotating or spinning slowly? This lower flexible drive shaft transfers power to rotate the trimmer head. Moderate DIY repair.

This lower boom assembly is a genuine MTD part, sold individually. This lower boom assembly can be used as a replacement part in a lawn mower or a lawn tractor. The purpose of the lower boom assembly in a lawn mower or a lawn tractor is to affix to the gearbox of the appliance.The lower boom assembly might need to be replaced at some point in the lifespan of a lawn mower or a lawn tractor. To facilitate the replacement, the operator must unscrew the screws within the upper and lower shaft, remove the malfunctioning or damaged boom assembly, separate the gearbox from the shaft, secure the gearbox to the new shaft, and then place the new boom assembly where the old boom assembly was. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This lower boom assembly is compatible with the following outdoor appliance brands: MTD, Troy-Bilt, and Cub Cadet.

This replacement part is a short block. It is a genuine replacement part made by MTD. A short block is a part that is found inside the engine. It comprises a portion of the cylinder block below the head gasket but above the oil pan. This helps the engine run smoothly overall as well as start and stop the engine efficiently. A new short block might be needed if the user notices that the current one is damaged in any way including being bent, dented, cracked, or chipped. If the user hears unusual noises coming from inside the machine it is possible that the short block is malfunctioning. This can be due to normal wear and tear over time. If this is the case it is recommended that the user replace this part immediately. This is a genuine OEM replacement part. This short block is sold individually and is sourced directly from the manufacturer.

Weak suction or airflow issues? This vacuum tube assembly channels air properly in your leaf blower. Moderately easy repair for most DIYers.

Fixes trimmer head not spinning or intermittent cutting. Replace the lower drive shaft assembly when vibration increases or head rotation stops. 30-minute repair.

Replace a lost, stripped, or corroded mounting screw in your edger or handheld power equipment. This hardware secures components during operation.

Blower won't start or functions intermittently? Faulty wiring harness may be the cause. This wire assembly connects electrical components together.

Fix fuel leaks or starting problems with this gas line trimmer fuel tank assembly. Direct replacement for worn or cracked tanks. Moderate DIY repair.

Engine gasket for landscape equipment. Seals components to prevent leaks. Replace if worn, cracked, or leaking. Verify compatibility with your model.

This oil filler cap is a genuine MTD part, sold individually. This oil filler cap can be used as a replacement part in a pole pruner. This part seals the oil tank and protects from leaks or the accumulation of debris.The oil filler cap in a pole pruner might have to be replaced if it is punctured, dented, cracked, ripped, torn, scraped, warped, or eroded to the point that the area around the oil filler cap is not sealed off to internal or external exposure. If this occurs, the oil filler cap should be removed and replaced by this genuine OEM replacement part.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This oil filler cap is compatible with the following outdoor appliance brands: MTD and Cub Cadet.

This gasket is a genuine MTD part, sold individually. This gasket can be used as a replacement part in a pole saw. The purpose of the gasket in a pole saw is to create a seal between the gasket and the area to which it is stably affixed so that debris cannot pass inside and that gas, fuel, and air flow cannot pass from the inside of the appliance outside.The gasket in a pole saw might have to be replaced if it is blown at some point within the typical lifespan of the pole saw. If the gasket is punctured, dented, cracked, pierced, warped, eroded, or otherwise damaged to the point of reduced efficacy, the gasket should be removed and replaced by this genuine OEM replacement part in order to ensure proper use of the appliance and safety for the operator.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This gasket is compatible with the following outdoor appliance brands: MTD, Craftsman, Troy-Bilt, and Cub Cadet.

This replacement part is a bar. This is a genuine replacement part made by MTD. This specific part is typically found in chainsaws. The bar holds the chain in place and connects the moving parts to the user settings at the top of the machine.A new bar might be needed if the current one is damaged in any way. This might include being dented, bent, or cracked. If the bar is not in working condition, the chain will most likely not be able to stay in place and the entire machine could be useless. Be sure to wear work gloves as this part is close to the chain in the chainsaw and can cause injury. This part is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit.

This genuine replacement part is a MTD 14 inch chain for use with chainsaws. A properly functioning chain is essential for the safe and reliable use of a chainsaw. The chain attaches to the cutting bar and rotates quickly to provide cutting functionality. The chain may become worn out or damaged due to extended use, necessitating replacement. Remember to check the chain periodically to spot any wear or damage. This part is an identical replacement for a chain that is missing, worn out, or damaged. Prior to working with this part, please refer to the original product manual for a full list of included parts and installation instructions. Additional tools may be required for installation of this part. For safety, always wear gloves and ensure unit is powered down prior to performing any installation or repair.This high quality OEM replacement part is sourced directly from the manufacturer, and is sold individually. It is made of high-quality durable metal. This part is compatible with Troy-Bilt, Cub Cadet, and other chainsaws. Please note: original part numbers 214919, 214919-33, and MC-6220-210803 are now obsolete, and manufacturer has replaced the original part numbers with this part.

Engine won't start or runs rough? This carburetor mixes fuel and air for smooth operation. Essential for restoring proper engine performance in handheld products.