Troy-Bilt Parts

This short block assembly is a genuine MTD part, sold individually. This short block assembly can be used as a replacement part for a string trimmer, a tiller, or an edger. The short block includes the crankshaft, piston, rod, camshaft, valves, and governor. A short block assembly might be necessary if there is damage to a wide range of parts in the equipment's engine. Check for frequent stalling, misfires, or an inability to power on. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This short block assembly is compatible with the following brands: MTD, Craftsman, and Cub Cadet.

This part is a replacement cutting head assembly. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a broken or defective cutting head assembly on trimmers. The cutting head contains the cutting line that is used to trim plants and greenery. The cutting head experiences significant wear and tear over time, in particular, the cutting line itself. It will likely require replacement in the standard lifespan of the trimmer. It's advisable to wear work gloves to protect the hands. It's important when working on or near an engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this cutting head assembly, the appropriate owner's manual and equipment diagrams should be utilized.As an authentic replacement part, this cutting head assembly is suitable for use on several models of trimmers manufactured by MTD, Troy-Bilt, Yard Machines, and other brands. This is a genuine part made of high-quality, durable materials and is sold individually.

This belt is used for snowblowers. When the machine is running, the belt turns and propels the auger, which then blows the snow through the chute. If the belt is broken or otherwise not functioning properly, the snowblower will not work.The belt may need to be replaced for any number of reasons. It could become damaged while in use, although this is rare. Over time, the belt could start to stretch and weaken. It may not longer provide the same level of efficiency as when it was new. There is also the chance that the belt could snap. When replacing the belt, it is recommended that the owner also clean the pulleys. This can prevent premature wear and tear.This snowblower belt is for use with many models from MTD, Yard Machines, Cub Cadet, and Troy-Bilt. The belt is a genuine OEM replacement part sourced from the manufacturer. It is sold individually.

This spindle pulley is a genuine MTD part, sold individually. This spindle pulley can be used as a replacement part in an edger. The purpose of the spindle pulley in an edger is to affix to the drive belt and to the blade so that the blades can be spun and rotated during the typical use of the appliance by the operator.The spindle pulley could be cracked, broken, dented, warped, eroded, punctured, or otherwise damaged to the point of reduced or no functionality. If this occurs, the spindle pulley should be removed and replaced by this genuine OEM replacement part so that the edger can continue to be used in standard operation by the operator of the appliance.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This spindle pulley is compatible with the following outdoor appliance brands: MTD and Troy-Bilt.

This genuine OEM replacement part idler pulley plays an important part on many lawn tractors, mowers, and snowblowers. It drives the engine's belt system, particularly the belts connected to the crankshaft. It helps to create motion throughout the engine, including in the steering pump, air compressor, and the alternator. Therefore, without this pulley, the engine will not function properly. As with any part of an engine, an idler pulley will begin to wear down over time. When this happens, an idler pulley will begin slipping, causing the belts to no long run smoothly. If an idler pulley breaks completely, the engine will not start. Before replacing an idler pulley, be sure to let the engine cool completely, as you will have to remove several parts with a screwdriver and socket wrench set. This idler pulley will work with Troy-Bilt, Yard Machines, MTD, Cub Cadet, and Yard Man appliances. It is a high-quality replacement part sourced directly from the original manufacturer. This part ships individually.

This replacement part is a flywheel combo. This is a genuine replacement part made by MTD. This part is a flywheel connected to a pulley. The combination makes it an important part of many engines and is used to transfer forces to different objects so that the user may operate the machine properly during use. A new flywheel combo might be needed if the current one is no longer working. If the pulley area of this part has been stripped down due to friction, it would be a good idea to replace the flywheel combo. Be sure the engine is turned off before replacing this part to prevent injury during the repair. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This locking rod is a genuine MTD part, sold individually. This locking rod can be used as a replacement part in a log splitter. The purpose of a locking rod in a log splitter is to serve as a fastening component that holds one or more parts together.The locking rod in a log splitter might need to be replaced with this genuine OEM replacement part at some point within the typical lifespan of the appliance. This could occur if the locking rod is damaged in the form of puncturing, scraping, denting, cracking, eroding, or warping. If this occurs, the locking rod should be immediately replaced in accordance with the proper set of instructions sourced from a relevant appliance manual.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This locking rod is compatible with the following outdoor appliance brands: MTD, Yard Man, Ryobi, Cub Cadet, Craftsman, and Yard Machines.

This replacement part is a baffle. It is a genuine replacement part made by MTD. This part can be added to different types of lawnmowers and is used to enhance the airflow underneath the mowing deck. This helps the grass clippings and other debris move smoothly into the bag or discharge chute. A new baffle might be needed if the user notices that the grass and other debris is moving in the wrong direction as it is turning into mulch. This can be because the air underneath the deck is not moving properly and the grass is not being deposited in the correct place. Be sure to refer to the user manual for more detailed instructions on how to replace or install this part. This baffle is sold individually and is sourced directly from the manufacturer. This is also a genuine OEM replacement part to ensure proper fit.

Slide shoes, otherwise known as skid shoes, are attached to a snowblower to help protect the concrete it moves over. The slide shoe also helps to protect the underside of the snowblower. They are composed of metal and are attached to the bottom of the machine. With use, the slide shoes may wear down. They can also become defective from accidents while operating the snow throwing machine. When the slide shoes are not working correctly, there can be irreversible damage done to both the snowblower and the concrete. Replacement slide shoes can easily be attached to the bottom of a snowblower. Be sure to allow the machine to cool down completely. It's recommended to set the snowblower on top of a piece of cardboard. Remove the old shoes and install the new ones, tightening all nuts and washers while the skid shoe is flat on the ground.This is a manufacturer supplied OEM MTD snowblower slide shoe. Each shoe is sold separately. The slide shoe is made of high-quality, durable black steel. It is suggested to replace both shoes simultaneously to ensure an even and consistent path for the MTD snowblower.

This blade retainer kit is designed for use with string trimmers and edgers by many manufacturers. It comes with a metal retaining washer that is used with the blade, as well as the needed spool cutting heads. This kit also includes the nut needed to fasten the blade to the gearcase. It is used to install a blade onto the trimmer while adding stabilization through the nut. The parts in the blade retainer kit can become worn out during use and may need to be replaced.When the blade needs to be replaced or a part of the blade retainer kit is broken, removing the parts is required. Moving the blade involves turning the retaining bolt while the equipment is on a level surface. Next, undo the bolt holding the blade so it can be removed. The blade can be replaced at this time, as well as the parts from this blade retainer kit.This blade retainer kit is made for edgers and string trimmers manufactured by Yard-Man, Craftsman, Bolens, Ryobi, MTD, Troy-Bilt, and Yard Machines. It is a single retainer kit that comes as a genuine OEM replacement part sourced directly from the manufacturer.