We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Show parts
Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.
Replace your dishwasher's inner tub assembly if cracked, damaged, or leaking. This structural component holds water and dishes during wash cycles.
Usually ships within 4 - 14 days
Fix a dishwasher that won't start or run because the door won't latch. This strike receiver allows the latch to engage and signal a closed door.
10 - 16 x 3/8 , hex
This part is discontinued by the manufacturer and is no longer available for purchase.
This roller assembly mounts to the bottom of a dishwasher dishrack and allows it to slide in and out of the tub smoothly. It typically includes the roller wheel, axle, and mounting clip. Replace this part if the dishrack is difficult to pull out, rolls unevenly, or if the roller is cracked, worn, or has fallen off the track.
Mounting screw for dishwasher assembly. Secures internal components and panels. Replace if stripped, corroded, missing, or damaged during repairs.
The Vent Blower Assembly is an OEM part for Frigidaire dishwashers. It is designed to help ventilate the dishwasher by expelling hot, moist air from the interior after the washing cycle.
You should replace the vent blower assembly if it becomes faulty. Causes of a bad vent blower assembly can include regular wear and tear, blockages from debris, or electrical issues. A malfunctioning vent blower can lead to poor drying performance and excessive moisture inside the dishwasher.
Symptoms of a bad vent blower assembly include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
This bezel is a trim piece for Frigidaire dishwashers that finishes and protects an opening on the door/control panel, helping the mating component sit properly while restoring a clean, factory look.
Replacement water inlet hose for dishwashers. Connects water supply to the tub. Replace if cracked, leaking, or damaged by pests or wear.
Flexible drain hose channels waste water from your dishwasher to the drain system. Replace if cracked, leaking, or damaged to prevent water backup issues.
Fix water leaking from your dishwasher or overfilling issues. This float assembly monitors water levels to prevent overflow and flooding damage.
Dishwasher won't fill with water? A faulty water level float switch prevents proper filling. This switch assembly typically takes 15 minutes to replace.
Fix a dishwasher that stops mid-cycle, overheats, or won't heat water. This thermostat regulates temperature during wash cycles. Moderate DIY repair.
Secures dishwasher thermostat to base for accurate temperature sensing. Replace if loose or broken to prevent overheating. Verify fit by model number.
Dishwasher door gasket foam creates a watertight seal to prevent leaks. Replace if you notice water escaping or the foam is compressed or torn.
Replacement mounting screw that secures control switches and switch assemblies to the dishwasher panel. Needed when original hardware is lost or stripped.
Replace a damaged or frayed wire harness in your dishwasher. This internal wiring assembly connects electrical components and may need replacement if cracked or worn.
Replacement mounting screws that secure your cooktop to the countertop or cabinet. Essential when original screws are stripped, missing, or damaged during installation or service.
Replacement mounting screw for dishwasher panels and internal components. Needed when original screws are stripped, missing, or corroded during repairs.
Replacement cabinet insulation panel for dishwashers. Installs inside cabinet to reduce heat transfer and noise. Needed when original is torn, compressed, or missing.
The Cabinet Seal Kit is an OEM replacement part for Frigidaire dishwashers. It is a kit that includes all the necessary rubber seals and gaskets to make sure a proper seal around the dishwasher door. The cabinet seals are designed to prevent water leakage and contain moisture and debris within the dishwasher. Causes of bad seals can include normal wear and tear over time, exposure to cleaning chemicals or detergents that degrade rubber seals, or damage due to improper installation. Symptoms of bad seals include:
This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
Replaces missing, torn, or saturated sound-dampening insulation blanket for dishwashers. Wraps around tub to reduce noise and protect cabinetry.
This side mounting bracket kit includes the hardware needed to secure a dishwasher to the adjacent cabinetry from the sides rather than from the countertop. It is commonly used in kitchens with granite, stone, or other countertops where top-mounting screws cannot be used. Replace this kit if the original brackets are bent, broken, or missing, causing the dishwasher to shift or slide during operation.