Parts for Ge GTS22KHPARBB: 09 - Unit Parts

Purifies water before reaching your dispenser and ice maker. Replace every 6 months for clean, safe drinking water. Verify fit with your model number.

Directs defrost water from the evaporator to the drain pan below your refrigerator. Replace if cracked, damaged, or clogged to prevent water pooling.

Replacement rear wheel for refrigerators. Mounts to the bottom rear frame to enable smooth rolling for cleaning and repositioning. Order if cracked or missing.

Cardboard or metal cover that closes the machine compartment opening on your refrigerator back panel. Replace if cracked, missing, or water-damaged.

Rear caster wheel assembly for refrigerators. Mounts under the back of the unit to provide smooth rolling mobility. Replace if cracked, broken, or worn.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Mounting screw for refrigerator interior components and panels. Replace if lost, stripped, or damaged during maintenance. Essential hardware for secure assembly.

Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.

Rubber bumper that cushions and mounts the evaporator fan motor assembly. Replace if cracked, deteriorated, or missing to reduce vibration and noise.

Rubber grommet that mounts the evaporator or condenser fan motor to its bracket. Replace when worn, cracked, or missing to reduce vibration and noise.

Replace a damaged or disconnected refrigerator wire harness. Restores electrical connections between components. Needed when wiring is frayed or broken.

Secures refrigerator wiring to prevent chafing and vibration noise. Replace when damaged or missing to keep harnesses organized. Confirm fit by model.

Replace a dead or noisy refrigerator fan motor to restore proper airflow and cooling. Fixes non-spinning or intermittently running fans. DIY-friendly.

Refrigerator running hot or making loud noises? A worn condenser fan blade prevents proper airflow across coils. DIY repair in 30 minutes or less.

Push rod pin for refrigerator assemblies. Installs to secure shelves, drawers, or mounting brackets. Replace if broken, missing, or worn over time.

10-32 x 5/16 machine-thread screw secures refrigerator panels, trim, and internal brackets. Replaces missing or damaged fasteners to prevent rattles.

Replace missing or stripped mounting screws in your refrigerator. This 12-pack of 8-32 thread screws secures panels, brackets, and components.

This rear condenser fan bracket secures the condenser fan assembly to the refrigerator chassis, helping keep the fan stable for proper airflow and efficient cooling. It restores correct fan alignment and reduces rattling or vibration. What it does:

• Holds the condenser fan motor and blade in the correct position behind the condenser coil
• Prevents fan wobble, rubbing, and metal-on-metal noise
• Helps maintain consistent condenser airflow for efficient cooling
• Useful when the original bracket is bent, cracked, or broken

• Disconnect power to the appliance before starting any work.
• Basic hand tools are typically required; handle sharp sheet metal carefully.
• Inspect surrounding mounting hardware and fan components; replace any damaged fasteners.

Refrigerator not cooling or compressor clicking on and off? This compressor kit restores cooling. Requires certified technician with specialty tools.

Provides start and run voltage to the compressor. Replace if cracked, damaged, or failing. Installs near the compressor at the bottom of the unit.

Refrigerator clicking but not cooling? A failed overload protector can prevent compressor startup. This part interrupts power during overheating.

Rubber grommet that mounts and cushions the compressor on your refrigerator or freezer. Replace if cracked, worn, or causing vibration noise from unit.

Filter drier for refrigerator sealed systems. Removes moisture and contaminants from refrigerant. Replace if frozen, iced over, cracked, or restricted.

Replacement shelf support stud for refrigerator shelves. Installs to hold shelves in place. Needed when original stud is broken, cracked, or missing.

Condenser air baffle for refrigerators. Directs airflow over the condenser coils. Replace if cracked, broken, or missing to maintain proper air circulation.

Replacement mounting screw for securing panels, trim, and internal components in appliances. Needed when original screws are stripped, lost, or damaged.

Replacement baseplate support for refrigerator high side assembly. Secures internal components in position. Needed when original plate is cracked or broken.

Guides airflow across the condenser and secures the fan motor in place. Replace if cracked, broken, or missing to restore proper cooling airflow.

Hex washer head screw for refrigerator assembly and panels. Replace this fastener if lost, stripped, or corroded during repairs or maintenance work.

Self-adhesive foam strip seals gaps between dishwasher components to reduce drafts, rattling, and moisture. Replace when worn or compressed. Verify fit with your model number before ordering.

Secures the condenser unit in your refrigerator. Replace if loose, broken, or causing vibration noise. Verify fit with your model number before ordering.

Covers the water line tubing on the back wall of your refrigerator. Replace if the original cover is cracked, broken, or missing to protect the tubing.

Secures water tubing to fittings in refrigerators and dishwashers. Replace if leaking, tubing slips off, or clamp is cracked. Confirm fit with model number.

Water dispenser won't shut off or no water flowing? This inlet valve controls water to your ice maker and dispenser. DIY repair in 10-15 minutes.

Plastic water line that connects the water inlet valve to the ice maker. Replace if cracked, leaking, or damaged. Includes installation video.