Parts for Kitchenaid KSB4028BS0: Unit Parts

This bezel is the outer trim that surrounds and protects the appliance control console, restoring a finished appearance and covering internal controls. It replaces damaged or worn trim to improve function and looks. What it does:

• Covers and protects the control panel area from spills, debris, and incidental contact
• Restores a finished, secure mounting surface for buttons, displays, and switches
• Replaces cracked, warped, loose, or cosmetically damaged trim pieces
• Helps prevent dirt and moisture from reaching internal components around the console

• One bezel

• Disconnect power to the appliance before beginning any work
• Removal typically requires releasing trim clips and/or removing a few screws; keep fasteners for reinstallation
• Handle edges and painted surfaces carefully to avoid scratches; use non-marring tools when prying clips

A general-purpose 6-20 screw used to secure panels, brackets and small components on Whirlpool appliances. Replaces stripped or missing fasteners to restore a snug fit and reduce rattling or loose parts. What it does:

• Secures appliance panels, trim, brackets and internal components in original mounting locations.
• Stops panel movement, vibration noise and loose connections caused by missing or corroded screws.
• Fits the OEM 6-20 thread designation used on multiple Whirlpool assembly points.
• Sold individually for spot repairs and small part replacements.

• Disconnect power or gas supply to the appliance before starting any repair.
• Use the correct screwdriver or bit to avoid stripping the head; tighten until snug but do not overtighten.
• Replace like-for-like; stop and verify the correct fastener for the mounting point.
• Check the appliance's parts diagram for the exact screw location and orientation.

This control board replaces the main electronic controller for select Andromeda-series air conditioners, restoring reliable power and system control. It provides the logic and relay switching the unit uses to manage fan and compressor operation. What it does:

• Receives user commands and runs the air conditioner's control logic for fan, compressor and mode selection
• Energizes relays and outputs to start/stop compressor and blower circuits
• Helps prevent erratic operation caused by a failed or intermittent control module
• Common symptom link: unit won't power on, cycles unpredictably, or shows control/display errors

• Disconnect all power to the appliance before servicing to avoid electrical shock
• Handle the board by the edges and avoid static discharge; use ESD protection if available
• Verify your appliance model and part number match before installation

This factory replacement screw fastens appliance components securely. Use it to replace lost, stripped, or corroded hardware and restore a snug, rattle-free fit and proper alignment of panels and assemblies.

• Secures panels, brackets, and internal components to their mounting points
• Replaces missing or damaged fasteners to maintain correct alignment
• Helps eliminate vibration and rattling caused by loose hardware
• Restores the original fit with OEM-matched threads and dimensions

• Disconnect power and shut off water or gas supplies before servicing
• Use the correct driver bit that matches the screw head to avoid stripping
• Replace one fastener at a time to keep parts aligned
• Tighten snugly; do not overtighten to prevent stripped threads or cracked plastic

The Blender Drive Coupling is an OEM replacement part for Whirlpool built-in blender bases. It connects the blending container to the electric drive motor below.

Causes of malfunction include wear from years of operation. Repeated blending torque stresses the components in alternating directions, eventually leading to fatigue and loosening. Accidental impacts can also damage the precision coupling pieces.

Symptoms of a failing blender drive coupling involve: 

• Inability to power blend jars or containers  
• Excessive vibration or grinding noises during use
• Loose, wobbly, or freely spinning attachments
• Reduced blending performance functionality  

This authentic Whirlpool replacement is compatible with some KitchenAid models.

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit