Universal Multiflex (Frigidaire) Parts

This center hinge pin supports the refrigerator door at the middle hinge and serves as the pivot point. Replacing a worn pin restores smooth door movement and helps the door align and seal properly.

• Acts as the pivot shaft for the door on the center hinge bracket
• Helps maintain correct door height and alignment for consistent sealing
• Wear or damage may show as door sagging, rubbing, squeaking, or not sealing/closing reliably
• Can reduce wobble or looseness felt at the center hinge

• Unplug the refrigerator and remove items from the door before service
• Support the door, remove hinge cover and screws, then lift the door off the center hinge
• Replace the pin in the center hinge/bracket, transferring any original spacers/washers as found
• Reinstall and level the door; verify the gasket seals evenly all around

The Adjustable Foot is an OEM part for Frigidaire dryers. This part is located at the bottom of the dryer and allows you to level it, ensuring stability and proper operation. 

Causes of a bad adjustable foot can include regular wear and tear, damage from moving the appliance, or breaking due to excessive weight or stress.  

Symptoms of a bad adjustable foot include:

• The dryer wobbling or tilting
• Difficulty in adjusting the height of the foot
• Visible damage or deformation of the foot
• Unusual noises or vibrations during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Shelf Support is an OEM part for Frigidaire refrigerators. Installed at set positions along the side walls, shelf supports provide sturdy surfaces on which to rest adjustable shelves or glass shelves. 

Causes of bad shelf supports can include general wear from repeated loading and unloading of shelves over time, as well as damage from accidental impacts.

Symptoms of bad shelf supports include:

• Shelves that wobble or sag in positions
• Difficulty inserting or removing shelves
• Small dents or breaks in the support surfaces
• Supports that are loosened from wall positions

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Shelf Support is an OEM part for Frigidaire refrigerators. This part provides stability and support for refrigerator shelves, ensuring that they remain securely in place and can hold the weight of stored items.

Causes of a bad shelf support can include accidental impacts, overloading the shelves with heavy items, or wear and tear over time. 

Symptoms of a bad shelf support include:

• Shelves that do not stay securely in place
• Sagging or tilting shelves
• Cracks or visible damage on the supports
• Difficulty in adjusting or repositioning shelves

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is the door bin for compatible refrigerators. It mounts on the inside of the door to hold bottles, jars, and condiments, restoring safe, organized storage when an original bin is cracked, loose, or missing. What it does

• Provides storage and organization on the refrigerator door
• Keeps items contained and accessible while the door opens and closes
• Replaces a bin that is cracked, warped, or broken
• Helps resolve issues like the bin falling off, not staying level, or not seating in the door rails

• 1 door bin

• Remove items from the old bin and lift it straight up and out of the door slots
• Align the new bin's hooks/tabs with the molded slots on the door liner
• Press down firmly until fully seated and secure
• Use care to avoid overloading; wear cut-resistant gloves to protect hands

The Light Switch is an OEM part for Frigidaire refrigerators. It is designed to control the interior lighting of the refrigerator; the switch activates when the door is opened and deactivates when closed. 

Causes of a bad Light Switch can include mechanical wear from frequent use, which may cause the switch to fail to engage or disengage properly. Electrical issues such as short circuits or loose connections can also prevent the switch from functioning correctly.

Symptoms of a bad Light Switch include:

• The refrigerator light staying on when the door is closed
• The light not turning on when the door is opened
• Flickering or intermittent lighting when the door position changes

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This refrigerator light socket holds and powers the interior bulb so you can clearly see inside. Replace a cracked, heat-damaged, or loose socket to restore reliable illumination when the interior light won't work or flickers.

• Provides the electrical connection and mounting point for the compartment light bulb
• Fixes symptoms such as no interior light with a known-good bulb
• Addresses intermittent flickering when the door is opened or closed
• Helps resolve visible charring, melting, or broken contacts on the socket
• Corrects a loose bulb that won't stay seated or lit

• Disconnect power to the refrigerator before servicing; remove the light lens/cover and bulb
• Note wire positions; release the old socket from its mount
• Transfer wires to the new socket one lead at a time and seat the socket fully
• Reinstall the bulb and cover; restore power and test
• Use only the bulb type and wattage specified for your model

Color: Grey

This replacement guide aligns and supports a moving component so it travels on its intended path without binding. Replacing a worn or broken guide restores smooth operation and helps prevent scraping, jamming, or premature wear of connected parts.

• Keeps the associated rack, drawer, or panel centered and properly aligned during movement
• Provides a track/stop for the mating part to follow
• Reduces friction and noise for smoother sliding
• Typical failure signs: sticking, uneven travel, scraping noises, or visible cracks/broken tabs

• Disconnect power; also shut off water or gas
• Remove the associated assembly to access the guide and note its orientation
• Reuse original screws/clips and tighten securely without overtightening
• Test movement after installation; replace worn mating rails or rollers if needed

This door stop limits the opening angle of the refrigerator/freezer door to prevent overextension that can stress hinges or strike nearby cabinets. Replacing a worn or missing stop restores controlled door travel and helps prevent impact damage.

• Controls and limits the door's opening range
• Helps protect hinges, gaskets, and adjacent cabinets from overextension
• Restores smooth, consistent door operation
• Common signs: door swings past normal position, door hits wall/cabinet, visible broken or missing stop

• Unplug the appliance and lighten the door if needed for easier handling
• Support the door; remove hinge fasteners or pin as needed to access the stop
• Match the orientation of the original stop; retain any shims/spacers in the same order
• Reassemble and verify door alignment and gasket seal

The Door Stop is an OEM part for Frigidaire refrigerators. This small part helps protect the appliance's door from damage and prevents it from impacting walls or adjacent cabinetry, ensuring the longevity and integrity of your refrigerator's exterior. 

Causes of a bad Door Stop can range from physical damage due to forceful door opening, to normal wear and tear from repeated use. In some cases, the mounting area for the door stop may become worn or damaged, affecting its ability to hold the door stop securely.

Symptoms of a bad Door Stop include:

• The refrigerator door swings open wider than usual
• Noticeable wear, damage, or breakage on the door stop
• Difficulty in opening or closing the door smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This oven bake element supplies the lower-oven heat for Bake cycles. Replacing a failed element restores proper preheating and consistent temperatures so your electric range or wall oven bakes reliably again. What it does:

• Provides radiant heat from the bottom of the oven during Bake
• Helps the oven reach and maintain the set temperature
• Failure symptoms can include: no heat in Bake, very slow preheating, uneven baking, or the element not glowing
• Visible damage such as breaks, blisters, or burned spots indicates replacement is needed

• One bake element

• Disconnect power at the breaker before servicing
• Remove oven racks; unfasten the element's mounting screws, then gently pull the element forward and transfer the wires one at a time
• Reuse existing mounting hardware; ensure terminals are fully seated and not contacting the oven cavity
• Restore power and test Bake; the element should heat evenly

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.

This replacement switch restores reliable on/off control of a specific function in your cooking appliance. When the original switch wears out, components may fail to power on, stay on, or work only intermittently. What it does:

• Opens and closes an electrical circuit to control a targeted component
• Used in select models to switch features such as a light, fan, or heating element
• Symptoms of a failed switch include no response, intermittent operation, or a component that won't turn off
• Visible heat damage, arcing, or loose terminals at the switch may also indicate failure

• 1 switch

• Disconnect power at the breaker or unplug the appliance before servicing; verify no voltage is present
• Note wire locations or take a photo; transfer wires to the new switch one at a time
• Reuse existing mounting hardware or brackets as applicable
• Restore power and test the controlled function before final reassembly

This damper control knob fits the refrigerator's air damper. It attaches to the damper control so you can open or close airflow between the freezer and fresh food compartments when the original knob is cracked, stripped, or missing.

• Attaches to the damper control shaft to adjust airflow from the freezer into the refrigerator compartment
• Direct replacement for a knob that is broken, missing, or stripped
• Symptoms can include a loose or slipping control, difficulty turning, or settings that won't stay in place
• If the control can't be turned, temperature response to damper adjustments may be inconsistent

• Disconnect power to the refrigerator before servicing
• Pull the old knob straight off the control shaft; avoid prying to prevent damage
• Align the new knob with the shaft and press it on until fully seated
• Rotate through the full range to ensure smooth operation without forcing

This factory wire harness routes electrical power and signals between the controls and internal components of your cooking appliance. Replacing a burned or brittle harness restores safe, reliable connections and helps prevent shorts or intermittent operation.

• Distributes power and control signals between the user interface/control system and internal components
• Replaces damaged wires or connectors that can cause no operation or intermittent function
• Helps address short-to-ground conditions that trip a household breaker
• Restores proper routing to reduce wire chafing and heat exposure

• Disconnect power at the breaker or unplug the appliance before servicing
• Photograph/label connections and transfer one connector at a time to match original locations
• Route along factory paths and secure with existing clips/ties; keep clear of sharp edges and hot surfaces
• Inspect mating terminals for heat damage and repair/replace affected parts before reassembly