Parts for Ge ZET2RM2SS: 02 - Upper Oven Parts

Secures the capacitor inside your oven. Replace if the bracket is bent, broken, or missing to properly mount and protect the electrical capacitor component.

Small rubber bumper that cushions contact between oven door and cabinet. Replace if cracked, missing, or worn to reduce noise and protect finishes.

Oven won't heat or shuts off after reaching temperature? The hi-limit thermal switch prevents overheating. DIY repair takes 30-60 minutes.

Insulation retainer clip secures insulation panels inside your oven cavity. Replace if clip is broken, cracked, or missing to keep insulation in place.

Replaces worn or damaged oven rack guide assembly. Restores smooth rack sliding and proper alignment. Needed when guides are cracked, broken, or missing.

Large broiler pan with grid for ovens and ranges. Replaces damaged, warped, or missing pans. Installs in broiler compartment for cooking meats and vegetables.

Replacement broiler pan that installs in your oven cavity. Needed when original pan is warped, rusted, damaged, or missing from your appliance.

Fix uneven baking and undercooked centers by replacing your failed lower bake element. Restores consistent bottom heat for proper oven performance.

Oven not heating properly or broiler not working? This broil heating element restores even high-heat cooking. Common DIY repair, typically installs in 30-45 minutes.

Fix F2 or F3 error codes with a new oven temperature sensor. Restores accurate heating when your oven shuts off or won't maintain temperature. 10-15 min DIY.

Retainer bolt secures internal components and panels in your range or wall oven. Replace if bolt is stripped, missing, or causing loose assemblies.

Restore bright, clear visibility inside your oven with this 20-watt halogen light bulb. Replace a burned-out bulb to monitor cooking through the window and safely see racks and dishes without opening the door. What it does:

• Illuminates the oven cavity when the light switch is used or the door is opened
• Helps you check cooking progress and locate items inside the oven
• Common symptoms: interior light won't turn on, is dim or flickers, or the bulb glass is broken
• 20-watt halogen design matches the original lighting specification

• 1 halogen light bulb

• Disconnect power at the breaker and allow the oven to cool completely
• Wear gloves or use a clean cloth; avoid touching the glass envelope
• Remove the lens/cover per your model instructions; carefully remove the old bulb and fully seat the new bulb
• Reinstall the cover, restore power, and test; use only the wattage/type specified for your appliance

Replace your burned-out or dim oven interior light bulb assembly to restore bright visibility while cooking. Confirm fit with your model number.

Halogen light bulb assembly for your oven. Replace when light dims, flickers, or burns out to restore interior visibility. Verify fit with your model.

This replacement crystal lamp provides the interior lighting for refrigerators, improving visibility so food and shelves are easier to see. Designed as a direct-fit replacement to restore a clear interior light. What it does:

• Illuminates the refrigerator interior to help you find items more easily.
• Replaces a cracked, broken, dim, or missing lamp assembly.
• Fits into the existing lamp housing and works with the original socket.

• Disconnect power to the appliance before starting any work to avoid electrical shock.
• Handle the lamp carefully—wear gloves or use a cloth to avoid cuts from glass.
• Remove old lamp assembly per the owner's manual; align and seat the new lamp securely in the housing.

Secures oven door glass to the door frame, preventing rattling and separation. Replace if glass is loose or vibrating. Confirm fit with your model number.

Hinge receiver bracket that mounts to the oven frame and secures the door hinge arm. Replace if cracked, stripped, or damaged to restore proper door support.

This probe thermistor monitors interior temperature and sends readings to the control board so your appliance can maintain the correct cooling cycle. It replaces a failed or inaccurate sensor to help restore proper temperature regulation. What it does:

• Senses air or evaporator temperature and reports it to the control module
• Commonly related to warm/freezing issues, incorrect temperature readings, or erratic cycling
• Used by the control system to trigger fans, defrost, and compressor operation as needed
• Works as a direct replacement for the listed OEM temperature probe

• Disconnect power before replacing to avoid shock or damage
• Handle the sensor tip and wiring gently to avoid damage to the element or insulation
• Route and secure the wiring so it does not contact moving parts or hot surfaces

Channels exhaust air from your wall oven to maintain proper ventilation. Replace this vent tube assembly if damaged, cracked, or disconnected for correct air discharge.

The Wall Oven Capacitor Motor is an OEM part for GE wall ovens. Located inside the oven cavity, this motor is responsible for turning the convection fan which circulates hot air for even baking and roasting. 

Symptoms of a bad capacitor motor include:

• Inability to select convection bake or roast features 
• Uneven cooking results 
• Lack of air circulation inside the oven
• Strange noises coming from the fan/motor area
• The convection fan not turning on 

Causes of failure can be wear over time, damage from debris inside the oven, or occasional voltage fluctuations which can degrade motor components.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Wire harness that connects the meat probe to your oven's control system. Replace if wiring is frayed, damaged, or connection fails to read probe temperature.

This is a replacement black screw used to secure interior or exterior appliance components. It provides a discrete, color-matched fastener to restore proper fit and stop rattles or loose panels. What it does

• Fastens trim, panels, brackets or control components where a small black screw is required
• Restores secure mounting to eliminate vibration, rattling or misaligned parts
• Matches finished appliance surfaces for a clean, unobtrusive look
• Simple hardware replacement for small fastener loss or damage

• One black screw

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver to seat the screw; avoid overtightening to prevent stripping or cracking surrounding material
• Keep track of small fasteners during disassembly and handle with care
• Replace with the exact part number if the original screw is damaged or the thread/length differs

This replacement mounting screw is used in cooking appliances to fasten components securely. It restores a tight, rattle-free fit so panels, brackets, or burner-related parts stay properly aligned during everyday use.

• Secures appliance components to the chassis or assembly
• Replaces a missing, stripped, or corroded screw
• Helps resolve loose panels, wobbling parts, or vibration noises
• Supports proper alignment of mounted parts

• Disconnect power at the breaker; for gas units, also shut off gas supply
• Allow the appliance to cool completely before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Tighten snugly without overtightening; replace damaged threads or hardware as needed

This is a replacement screw that can be used with many different types of household appliances. Screws fasten various pieces of machines together. They can also help to reduce the amount of vibration in the machine. If a screw is missing or damaged, it could cause a machine to stop working properly, or to vibrate more than it should.The screws are made from metal and will typically last for a long time. However, the threads and other parts of the screw can wear down with use. The screws could also become lost when making other repairs to the appliance. Replacement of the screws is generally easy, but it will depend on where it is placed.This item can replace certain screws found in various models of ranges, ovens, dryers, and microwaves from General Electric, Hotpoint, Whirlpool, and Kenmore. This is a genuine OEM replacement part sourced from the manufacturer. It is sold individually. Owners may want to have several replacements on hand in case they need them.

Replacement screw for securing panels, brackets, and internal components in ranges, ovens, and cooktops. Replace missing, stripped, or damaged screws.

Replacement screw for securing panels, brackets, and internal components. Needed when original hardware is stripped, missing, or damaged during repairs.

Mounting screw secures range components and panels. Replace if screw is stripped, missing, or damaged during appliance repair or maintenance work.

Black. 8-18 AB HXW 3/8

10-32 machine screw secures panels, brackets, door hinges, and handles in ovens and ranges. Replace missing, stripped, or broken screws for tight fit.