Parts for Ge PGS960FEL1DS: Upper Oven Parts

If your oven won't preheat or shows an F3 error code, this temperature sensor monitors oven heat and safety features. Direct plug replacement, 15-minute fix.

Seals the inner edge of your oven door to retain heat for even cooking. Replace if you notice heat escaping or uneven temperatures. Verify fit.

This broil element heats the top of the oven to produce high, direct heat for broiling and browning foods. Replaces a damaged or non-heating upper element to restore broil performance and even cooking on the top rack. What it does:

• Generates the high, direct heat needed for broiling and searing
• Heats when the oven is set to the "Broil" function
• Commonly used when the oven won't broil, the top of food isn't browning, or the element shows visible damage
• Works with the oven's broil control and thermostat to reach and maintain broil temperatures

• 1 broil element (upper oven)

• Disconnect power to the range at the breaker or unplug before servicing
• Handle element and terminals carefully to avoid bending or breaking mounting tabs
• Reconnect wiring exactly as found; if terminals are loose or corroded, replace connectors

This dual plunger switch completes dispenser controls when the dispenser lever is pressed, restoring proper water and ice dispensing response. It replaces a worn or failed dispenser actuator switch to help the dispenser register lever movement. What it does:

• Acts as the dispenser lever switch assembly, closing circuits when the lever/plunger is depressed
• Controls water and/or ice dispense signals to the dispenser control board or valve
• Commonly linked to symptoms such as no water or ice when pressing the dispenser, intermittent dispensing, or unresponsive dispenser lever
• Helps restore reliable electrical contact for dispenser operation when the original switch is faulty

• One dual plunger switch assembly

• Disconnect power to the appliance before beginning any work
• Shut off water supply if removing water-connected components near the dispenser
• Access typically requires removing the dispenser bezel or front panel to reach the switch; handle panels and connectors gently
• Reconnect wiring exactly as removed and verify operation before reassembling all panels

Holds and powers the interior oven light bulb for visibility while cooking. Replace if light flickers, won't turn on, or bulbs burn out frequently. Verify fit by your model number before ordering.

Uneven cooking or excessive heat outside your oven? This rear cavity insulation restores thermal protection and improves heating efficiency. DIY-friendly.

Rear insulation panel installs behind the oven cavity to contain heat and protect components. Replace if cracked, damaged, or missing to restore insulation.

Seals between the oven light lens and liner to keep grease and moisture out. Replace if damaged, cracked, or no longer sealing properly.

Oven door won't lock during self-clean cycle? This automatic door latch assembly secures your oven door when locked operation is required. DIY repair.

10-32 machine screw secures panels, brackets, door hinges, and handles in ovens and ranges. Replace missing, stripped, or broken screws for tight fit.

Metal angle support bracket that secures interior panels, shelves, or trim inside your range. Replace if cracked, bent, or missing to maintain proper alignment.

Dim or dark oven interior? This lamp cover protects and diffuses your range's light bulb for clear visibility. Replaces cracked or missing lens. Easy fix.

This cover latch secures the appliance's top access cover so it stays closed during use and lets you open the cover for service or maintenance. It restores a positive, smooth-closing latch action for safe access. What it does:

• Holds the top/access cover closed to prevent accidental opening during operation
• Provides a solid engagement point for the cover to snap or latch into place
• Replaces a broken, worn or loose latch that causes rattling or an unsecured cover
• Helps ensure proper alignment of the cover for safe servicing and operation

• Disconnect power (unplug or shut off breaker) before beginning any service
• Typically installs with simple snap-in or screw fasteners; keep fasteners from the original part

Replacement oven bottom panel for gas ranges. Covers oven cavity floor. Replace if warped, rusted, cracked, or damaged. Restores smooth baking surface.