Parts for Whirlpool LTE6234DT3: 01 - Washer / Dryer Control Panel Parts

Fix a washer that won't advance to rinse cycle or stops mid-program. This timer controls wash, rinse, and spin sequences. DIY install in 5-10 minutes.

Replacement timer knob for washers. Installs on the control panel to operate the timer dial. Order if your original knob is cracked, broken, or missing.

Replacement timer knob for washers. Installs on the control panel to operate the timer dial. Order if your original knob is cracked, broken, or missing.

Replace your washer dryer combo's worn, cracked, or missing control knob. This biscuit-colored knob installs on the control panel shaft for cycle selection.

White

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

This is a replacement timer knob/dial for your dryer that restores a secure grip and clear selector markings. It lets you turn the timer and select drying cycles when the original knob is cracked, loose, or missing. What it does:

• Replaces a worn, broken, or missing timer knob so the timer control turns smoothly
• Provides a visible selector marker for choosing dryer cycle settings
• Prevents slipping or intermittent engagement between control shaft and knob
• Matches the biscuit (light tan) color used on many appliance control panels

• Disconnect power before servicing the appliance to avoid shock or injury
• Most knobs pull straight off the control shaft; pull firmly and evenly to remove
• If required, remove the control panel or use a screwdriver to access retaining hardware
• Do not force the new knob onto a damaged or bent shaft; inspect the control shaft for wear

Restore smooth, accurate cycle selection with this replacement timer knob for your dryer. When the original knob is cracked, stripped, or missing, this part lets you reliably set the timer and choose drying programs again. What it does:

• Attaches to the timer shaft so you can set drying cycles and time
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps resolve issues like the knob spinning freely or not turning the timer
• Provides a clean, factory look in white

• 1 white timer knob

• Disconnect power to the dryer before servicing
• Pull the old knob straight off the timer shaft; use steady, even pressure if tight
• Align the new knob with the keyed shaft and press firmly until fully seated
• The pointer aligns with the control panel cycle markings before use

This genuine replacement screw fastens appliance panels and components where a 10-32 thread is required, restoring secure connections and reducing rattling or loose parts. It's a simple, reliable fix for loose trim, panels, or brackets. What it does:

• Replaces stripped, lost or corroded 10-32 threaded screws used on panels, brackets, and trim
• Restores secure attachment to stop vibration, movement, or rattling
• Matches OEM thread form for correct fit and engagement
• Used where a short 10-32 machine screw is specified by the manufacturer

• One 10-32 x 3/8 screw

• Disconnect power and/or water to the appliance before starting any repair
• Use the correct screwdriver or nut driver to avoid cam-out and head damage
• Thread by hand to start, then snug—avoid over-tightening to prevent stripped threads or cracked parts
• If screw engages metal-to-metal, apply appropriate torque and secure fit before reassembling panels

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Dryer won't start when you press the button? The start switch initiates the drying cycle. Simple 10-minute DIY fix with basic tools and our guide.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

Dryer not advancing cycles or staying on continuously? A failed timer prevents proper cycle operation. DIY repair in 10-30 minutes with basic tools.

Secures the door hinge to the cabinet frame. Replace if your bracket is bent, cracked, or broken to restore proper door alignment and support.

Right-hand endcap for washer dryer combo units in biscuit color. Replaces cracked, broken, or missing side trim pieces on your appliance exterior.

Endcap for laundry center control panel. Covers the edge of the control console for a finished look. Replace if cracked, broken, or missing.

This motor connector housing is the molded body that holds the motor's wire terminals for a secure, insulated connection. Replacing a cracked or heat-damaged housing helps restore reliable motor operation and prevent intermittent power issues.

• Organizes and insulates the motor's wiring terminals
• Locks the harness to the motor for a firm electrical connection
• Helps reduce loose contacts, arcing, and heat damage at the plug
• If the housing is failing, you may see intermittent or no motor operation, the machine stopping mid-cycle, or visible melting/discoloration at the motor connector

• Disconnect power; also shut off gas supply
• Note wire positions; transfer terminals into the new housing one at a time to maintain orientation
• Inspect terminals and wiring; replace any burnt or loose terminals before reassembly
• Ensure the connector seats fully on the motor and the harness is secure; restore power and test

Secures and stabilizes the washer drum assembly. Replace if loose, rattling, or causing excessive vibration during spin cycles. Verify fit with your model.

Endcap for laundry center and washer dryer combo units. Covers and protects exposed edges or corners. Replace if cracked, broken, or missing.