Whirlpool Drawer, Shelf, Pan

This replacement freezer basket restores organized frozen storage and keeps items contained for easy access. It fits in the freezer compartment and provides a removable tray for holding packaged foods and loose items. What it does:

• Holds and organizes frozen food so items stay separated and accessible
• Prevents small items from falling into hard-to-reach areas of the freezer
• Replaces a cracked, bent, or missing freezer basket to restore usable storage
• Reduces rattling by keeping loose items grouped together

• Remove food from the area before installing to avoid spills or contamination
• Slide the basket into the freezer rails or ledges until it rests securely; no special tools usually required
• Inspect mounting rails or clips for damage and replace them if the basket does not seat properly
• Clean with mild detergent and dry thoroughly before returning food to the basket

This pan assembly sits under the appliance tub or base to catch and direct water away from internal components, helping contain leaks and prevent water damage. It replaces a damaged, cracked or warped pan. What it does:

• Collects and channels leaking or overflowing water away from electronics and flooring
• Restores the appliance's original drip containment and sealing surface
• Helps stop visible water pooling beneath the appliance
• Supports proper routing to drain points when used with the factory drain path

• Disconnect power and water supply before starting any repair
• Remove access panels and any components blocking the pan
• Handle carefully; edges may be sharp and gaskets or clips can be brittle with age
• Secure any fasteners, hoses, or seals to prevent new leaks

This Support is a replacement mounting bracket that stabilizes and secures appliance components for reliable operation. Restores proper fit and helps prevent movement or misalignment that can cause noise or part wear. What it does:

• Provides a secure mounting point for associated panels or components
• Helps keep moving parts aligned to reduce rubbing, vibration, or rattling
• Restores original fit when a worn or broken support causes looseness
• Suitable when a damaged bracket is visible or when parts shift out of place

• One Support

• Basic hand tools required; disconnect power and water before starting
• Inspect surrounding fasteners and replace any that are stripped or damaged
• Tighten to OEM torque if specified in manufacturer instructions; avoid over-tightening

This door shelf bin is a direct-fit replacement that restores secure storage on the refrigerator door and keeps cans, bottles and other items from shifting or falling. Made to match the original fit and mounting points. What it does

• Replaces a cracked, broken or missing refrigerator door shelf so items stay supported and organized.
• Restores the original mounting and snap-in function so the bin locks into the door rails.
• Prevents stored items from falling or shifting during normal door use.
• Matches the OEM shape and capacity for proper alignment with adjacent bins and door features.

• Remove all items from the door and lift out the damaged bin before installing the replacement.
• Align the bin with the door rails and snap it into place; confirm it seats fully on both sides.
• No tools or electrical disconnection typically required.
• Wear gloves to protect hands from sharp edges on broken plastic and to avoid fingerprints on clear surfaces.

This outer door trim restores the finished edge and appearance of an appliance door while helping hold the door assembly and glass in place. It replaces damaged or worn trim to stop rattles and improve the door's fit and look. What it does

• Covers and protects the exposed edge of the door for a finished appearance
• Helps secure the door glass and inner components to prevent movement or vibration
• Stops drafty or loose-feeling doors caused by cracked or missing trim pieces
• Prevents dirt and moisture from entering the door cavity at the trim seam

• Disconnect power (and gas if applicable) and remove any food or racks before starting
• Handle door glass and trim edges carefully to avoid breakage or cuts
• Follow the appliance service manual for proper removal and reassembly of the door panel

This support holds and stabilizes an appliance component to keep parts aligned and reduce vibration for reliable operation. It's a simple replacement that restores proper fit and function where a worn or broken support causes issues. What it does:

• Secures and aligns adjacent components or assemblies to prevent shifting during use
• Stabilizes moving parts to reduce vibration, noise, and rubbing
• Helps maintain sealing and clearance to avoid wear or interference
• Commonly replaced when cracked, broken, or missing and causing rattling, misalignment, or instability

• One support as shown

• Inspect surrounding clips and fasteners; replace any that are damaged
• Use correct screws or hardware and tighten to OEM torque where specified
• Disconnect power and follow safety guidelines before working on the appliance

This trim is the finished control-panel surround that restores the appliance's exterior appearance and helps protect internal controls from spills and debris. It fits into the front console area to provide a clean, factory look. What it does:

• Replaces a cracked, scratched, or missing control-panel trim to improve appearance
• Helps shield buttons and display edges from moisture and dirt
• Restores proper alignment and fit of the front console components
• Useful when trim gaps or cosmetic damage expose internal parts

• Disconnect power to the appliance before starting any work to avoid shock or injury.
• Remove adjacent trim or bezels as needed to access mounting screws; keep fasteners for reassembly.
• Handle trim carefully to avoid scratching the finish; align clips/tabs before securing.
• Replace any damaged or missing clips or screws to ensure a secure fit.

This rail secures and guides the washer lid, restoring proper lid alignment and smooth opening/closing. Replaces a worn, cracked, or loose lid rail to reduce rattling and prevent the lid from catching during use. What it does:

• Provides a stable mounting surface for the washer lid so it opens and closes evenly
• Guides lid movement and helps prevent misalignment or binding
• Reduces noise and rattling caused by a loose or damaged rail
• Helps keep the lid seated correctly to prevent accidental gaps or snags

• Typical install requires removing the top or accessing the lid hinge area; retain original fasteners unless replacements are provided
• Disconnect power to the appliance before starting work to avoid injury

Right hand side

Left hand side

Right hand side