Whirlpool Drum, Bulkhead, Front Parts

Replacement dryer drum that holds and tumbles laundry so air circulates evenly for efficient drying. Restores a smooth rotating drum surface to prevent fabric damage and improve drying performance. What it does:

• Houses and tumbles clothes while allowing heated air to pass through the load.
• Replaces a dented, cracked or scored drum that can catch or abrade fabric.
• Stops metal-on-metal scraping or grinding noises caused by a damaged drum surface.
• Helps eliminate uneven drying caused by a misshapen or warped drum.

• One replacement drum.

• Disconnect power (and gas supply for gas models) before starting any repair.
• Drum removal usually requires loosening the front panel and supporting the drum; consider a second person—the drum is heavy and awkward.
• Inspect and replace related components if worn to prevent repeat failures.
• Test-run the dryer after installation to ensure smooth rotation and proper clearance.

This bulkhead is the front tub housing that supports the washer drum and seals the washer cabinet to help contain water. Replaces a cracked or corroded housing to restore proper drum alignment and help prevent leaks. What it does:

• Provides structural support for the washer tub and drum assembly
• Forms the front seal surface to help keep water inside the washer
• Helps maintain correct drum alignment to reduce noise and wobble
• A failing bulkhead can cause visible leaks, excessive vibration, or rubbing noises

• Disconnect power and water supply before starting any repair
• Inspect surrounding seals, gaskets, and mounting hardware when replacing the bulkhead
• Replacement may require partial disassembly of the washer cabinet and drum; follow OEM instructions

This bulkhead is the structural panel that supports and seals the washer tub and provides mounting points for related components. It restores proper alignment and containment so the washer can hold and drain water correctly. What it does:

• Provides a secure mounting surface for the tub, seals, and associated fittings
• Helps route and contain water inside the washer cabinet to prevent leaks
• Maintains correct alignment for the tub and connected components
• Commonly replaced when leaks, cracks, or warped mounting surfaces cause water loss or misalignment

• One bulkhead panel

• Turn off power and water supply before beginning any repair
• Handle gently to avoid damaging mating surfaces or embedded seals
• Verify matching orientation and fastener locations to the original part
• If seals or gaskets are attached separately on your model, replace them as needed

This bulkhead is the front structural panel that supports the dryer drum and seals the front of the cabinet to maintain proper airflow and drum alignment. Replacing a worn bulkhead restores stable drum rotation and prevents air leaks. What it does:

• Supports the drum and front bearing to keep the drum centered and turning smoothly
• Seals the front cabinet to direct exhaust airflow through the blower and vent
• Reduces rubbing and vibration caused by a damaged or warped bulkhead
• Helps eliminate airflow leaks that can extend dry times or cause overheating warnings

• One bulkhead

• Disconnect power (and gas supply if applicable) before any service
• Service typically requires removing the dryer front panel and drum for access
• Inspect and replace any worn gaskets, bearings, or fasteners while replacing the bulkhead

This replacement dryer drum restores the rotating drum that holds and tumbles clothes during drying, helping ensure proper airflow and even drying. It's a direct-fit exterior rotating drum used in compatible Whirlpool-family dryers. What it does:

• Replaces a cracked, dented or warped drum that can catch or damage clothing
• Restores smooth tumbling to reduce noise and fabric snags
• Maintains proper airflow path for efficient drying performance
• Works with existing rollers, bearings and seals when those components are serviceable

• High-level task: remove cabinet and front bulkhead to access and swap the drum; follow your model-specific service manual
• Disconnect power (and gas supply for gas dryers) before starting any repair
• Inspect and replace worn rollers, glides, seals or bearings as needed—this drum typically does not include those components

This is a drum assembly intended for use with dryers. This part can be found inside the dryer and is responsible for holding clothing while a cycle is running. It holds wet laundry while loading the appliance. Over time and with use, the drum assembly can start to wear out. This can cause the dryer to squeal, start and stop during a cycle, make buzzing noises, or seize up.If the drum assembly is damaged, it will need to be replaced. Make sure to have basic tools and a pair of work gloves ready. The dryer should be turned off and unplugged from the wall. Raise the top panel, remove the front panel, and then remove the drum. The drum support roller should be taken out and installed on the new drum. Reinstall with the new component and reassemble all parts before use.The drum assembly is made to be used with dryers and washer/dryer combos from Inglis, Estate, Admiral, Crosley, Roper, Magic Chef, Amana, KitchenAid, Maytag, Kenmore, and Whirlpool. It is a genuine OEM replacement part that is sourced directly from the manufacturer. The part is sold on an individual basis.

Replacement dryer drum that holds and tumbles clothes during the drying cycle, restoring smooth rotation and preventing fabric damage. Replaces a dented, cracked, or noisy drum to improve drying performance. What it does:

• Spins and supports laundry inside the dryer so air circulates and items tumble evenly.
• Replaces a drum that is dented, warped, cracked, or rubbing—common causes of thumping, scraping, or fabric snags.
• Helps prevent further wear by restoring the smooth inner surface that clothes contact during drying.
• Works with the dryer's belt, rollers, seals and glides; damaged related components can cause repeat noise or wear.

• Disconnect power (and shut off gas supply on gas models) before starting any repair.
• Basic removal usually requires taking off the dryer front or top panel and sliding the old drum out.
• Inspect and replace worn rollers, belt, seals or glides when installing a new drum to avoid premature failure.
• Handle the drum carefully — edges may be sharp and some drums are heavy; use gloves and a second person if needed.

This replacement dryer drum is the rotating tub that holds and tumbles clothes while channeling airflow for even drying. Swap a damaged drum to stop rubbing noises, fabric snags, and uneven tumbling. What it does:

• Rotates inside the dryer cabinet to tumble laundry and direct hot air through the load.
• Supports the drum belt and rides on rollers/glides for smooth operation.
• Replace when you see dents, cracks, deep gouges, or metal-to-metal contact.
• Common symptoms of a failing drum: scraping or grinding noises, clothes catching, visible drum damage, or uneven tumbling.
• Inspect rollers, glides, and belt when replacing the drum.

• Disconnect power (and turn off gas supply for gas dryers) before beginning any repairs.
• Support the drum when removing or installing to avoid dropping or damaging the cabinet or finish.
• Installation typically requires removing the dryer front or top panels and repositioning the belt and rollers; have basic hand tools ready.
• If you hear persistent noises after install, recheck belt alignment, roller condition, and cabinet mounting.

This drum is the rotating tub that holds clothes and provides the tumbling action needed for cleaning or drying. It restores the drum surface and rotation area to help the appliance tumble items properly. What it does:

• Replaces a damaged, dented, or cracked drum to restore a smooth tumbling surface
• Supports normal rotation so clothes move through the wash or dry cycle evenly
• Helps reduce rubbing, scraping, or loud metal-on-metal noises from the cabinet
• Addresses symptoms like visible drum damage, fabric catching, or items not tumbling

• One replacement drum

• Disconnect power and water before starting any repair
• Installation typically requires disassembling the front or top panel and removing the old drum, belt, and related fasteners
• Inspect and replace worn belts, rollers, seals, or bearings while servicing the drum

The Bulkhead is an OEM component for Whirlpool dryers. As a structural panel, it secures the rear of the appliance while enabling airflow behind sliding doors. 

Formed from durable composite, the lightweight bulkhead installs easily into precise slotted tracks inside the chassis. This allows full retraction during maintenance without removing additional panels. 

Causes of a faulty bulkhead can include cracked welds or screws stripping their anchors from extreme force vibration over many years of use.

Causes of a bad bulkhead can include:

• Noisy rattling and resonance as the dryer operates  
• Restricted door movement from misalignment
• Inability to fully access internal components  
• Excessive ducting leaks from gasket compression failure

Replace yours with this genuine Whirlpool bulkhead to restore smooth, tight operation. Compatible with Kenmore, Maytag, and KitchenAid dryers.