Whirlpool Duct Parts

The Heater Box is an OEM part for Whirlpool dryers. It houses the heating element that generates the hot air required to dry clothes efficiently. The heater box ensures optimal heat distribution within the dryer, contributing to uniform and effective drying cycles. 

Causes of a bad Heater Box include overheating, which can warp or damage the box, restrictions in airflow causing inefficient heating, and physical damage that can compromise the box's integrity. 

Symptoms of a bad Heater Box include:

• Clothes taking longer than usual to dry
• The dryer operating at higher temperatures than normal
• Unusual noises during operation, indicating potential airflow or mechanical issues
• The outside of the dryer becoming unusually hot during cycles

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Side and bottom exhaust kit.

This 6-foot dryer vent duct connects your dryer's exhaust outlet to the wall vent. It provides a secure path for moist air to exit the home, helping maintain airflow and consistent drying performance. What it does:

• Vents hot, moist air from the dryer to the exterior
• Replaces crushed, torn, or lint-clogged ducting
• Helps address longer dry times, heat buildup/shut-offs, or moisture and lint around the dryer
• Supports a short, direct run to reduce kinks and airflow restrictions

• One 6-foot dryer vent duct

• Disconnect power; for gas models, turn off the gas supply before starting
• Pull the dryer forward and remove old ducting and lint/debris from connections
• Attach the duct fully to the dryer outlet and wall vent and secure with clamps; avoid sharp bends or crushing
• Move the dryer back carefully and confirm strong airflow at the exterior vent hood

This air duct assembly routes airflow inside the appliance to maintain consistent circulation and temperature control. Replacing a cracked, warped, or blocked duct restores the designed air path, improves performance, and reduces hot or cold spots.

• Directs and balances airflow through internal channels as designed
• Helps maintain stable temperatures and reduces moisture or frost around vents
• Preserves a sealed air path to minimize leaks, noise, and inefficiency
• Typical symptoms of a failed duct include uneven temperatures, weak airflow, frost/condensation near vents, or visible cracks/broken tabs

• Disconnect power before servicing; allow any ice buildup to thaw for easier removal
• Remove shelves/covers to access the duct; keep track of screws and clips
• Note orientation; transfer any reusable seals, gaskets, or sensors from the original assembly as needed
• Ensure vents are clear and seals are seated; restore power and allow up to 24 hours for temperatures to stabilize

This replacement terminal box encloses the dryer's rear power-cord connection area. It shields the terminal block and wiring to help prevent arcing and heat damage, supporting safe, reliable operation.

• Houses and protects the terminal block and cord connections at the rear of the dryer
• Provides mounting points for the cord strain relief and cover
• Helps contain heat from loose/overheated connections to reduce risk of damage
• Damage here can contribute to scorching/melting at the cord entry, tripped breakers, or intermittent/no power

• Disconnect power before servicing; for gas dryers, also shut off gas supply
• Access the rear terminal area and document wire routing before disassembly
• Install the new box using existing hardware; transfer wiring and reattach the cover/strain relief
• Tighten terminal screws securely and verify correct cord configuration before testing

WPL VENT KIT, 4-WAY ULT

This exhaust kit connects the appliance's blower outlet to exterior ductwork, restoring smooth, directed airflow. Replacing a damaged or missing adapter helps clear steam, smoke, and odors more effectively and reduces recirculated air. What it does:

• Couples the blower outlet to the home's exhaust ducting for outside venting
• Helps guide airflow in the correct direction during fan operation
• Addresses weak venting, air leaking at the grille, or rattling from the vent path
• Replaces cracked, warped, or missing exhaust-adapter components

• One exhaust kit

• Disconnect power before servicing; allow hot surfaces to cool
• Dry-fit parts, then secure per manufacturer instructions; seal joints with foil HVAC tape
• Use rigid metal duct where required; avoid sharp bends and crushed ducts; wear cut-resistant gloves

This out exhaust pipe directs a dryer's exhaust airflow from the appliance to the home vent, helping remove moisture and lint from the dryer cabinet. Durable replacement for worn or damaged exhaust tubing. What it does:

• Channels hot, moist air from the dryer to the external vent to prevent moisture buildup
• Helps maintain proper airflow for efficient drying and reduces lint accumulation inside the cabinet
• Replaces cracked, crushed, or disconnected exhaust connections that cause poor venting or air leaks
• Works as a direct-fit plumbing piece when original exhaust piping is damaged

• One out exhaust pipe

• Disconnect power to the appliance before installing; for gas dryers, turn off gas supply and pilot per manufacturer instructions
• Ensure the pipe fits securely to the dryer outlet and the wall vent; use manufacturer-recommended clamps or fasteners
• Inspect and clean the vent path and lint screen while replacing the pipe to ensure safe airflow

This elbow is a molded hose connector that redirects fluid or airflow in the appliance, restoring proper routing for drainage or vent lines. It helps stop leaks and maintains correct hose alignment for reliable operation. What it does

• Redirects hose or duct routing at an angle to fit tight spaces
• Restores a secure connection where a cracked or broken elbow causes leaks
• Helps prevent kinks or pinched hoses that can cause poor drainage or reduced airflow
• Supports proper sealing when used with the correct clamps or gaskets

• One elbow connector

• Disconnect power and shut off water before replacing the part
• Inspect mating hose ends and clamps; replace damaged hoses or clamps for a secure seal
• Ensure correct orientation and fully seat the elbow before tightening clamps
• Do not force the part into place; confirm fit and alignment to avoid stress or leaks

This transition duct directs dryer exhaust from the appliance to the home vent, helping maintain proper airflow and reduce vent leaks. It keeps exhaust moving out of the cabinet for safer, more efficient drying. What it does:

• Channels dryer exhaust from the appliance outlet to the household vent
• Helps prevent lint and moisture from escaping into the cabinet or laundry area
• Can reduce long dry times and overheating caused by restricted or damaged ducting
• Commonly replaced when venting is crushed, torn, or leaking

• Disconnect power (and gas, if applicable) and move the appliance away from the wall before replacing the duct
• Inspect adjoining vent hoses and seals; replace or reseal as needed for a tight fit
• Use appropriate clamps or connectors and follow local venting codes for safe exhaust routing

This wall elbow redirects the dryer vent through a wall opening, keeping the exhaust path secure and aligned for safe, efficient venting. Replaces a worn or damaged elbow to help restore proper airflow. What it does

• Provides a finished transition from the dryer vent pipe to the wall recess.
• Helps maintain a sealed vent path to reduce air leakage and lint buildup.
• Common fix for a cracked, loose, or broken elbow that causes noisy or inefficient venting.
• Works with standard dryer vent systems where a recessed wall box is used.

• Designed for use with compatible dryer vent housings;
• Turn off and disconnect the dryer before servicing; wear gloves to protect hands from sharp metal edges.
• Inspect surrounding venting and clear lint before final assembly to improve airflow and safety.

This 5-foot flexible vent hose provides a replacement vent path for your dryer, restoring proper airflow to help clothes dry efficiently and reduce lint buildup. It's a straight, flexible vent designed for inline dryer ducting. What it does:

• Channels hot, moist air from the dryer to the home vent outlet to help shorten drying cycles
• Helps prevent lint accumulation in the dryer exhaust path when properly installed and maintained
• Can resolve symptoms like longer dry times, reduced airflow from the dryer, or overheating due to restricted venting
• Works as the inline connector between the dryer outlet and the household vent opening

• One 5 ft flexible dryer vent hose

• Disconnect power (and gas supply for gas dryers) before replacing the vent; follow all safety precautions
• Ensure the hose is not crushed or kinked and has a smooth path to the exterior vent for best performance
• Use proper clamps or fasteners to secure both ends and check for leaks after installation
• Clean lint from the dryer and duct before installing the new hose to maximize airflow

This dryer elbow is the molded duct connector that redirects exhaust from the dryer to the vent duct, helping restore proper airflow and reduce leaks around the outlet. It's a simple replacement for a cracked or loose elbow. What it does:

• Connects the dryer's exhaust outlet to the home vent duct to direct hot, moist air outside
• Replaces cracked, broken, or warped elbows that cause air leaks or rattling
• Helps reduce lint escape and improves exhaust path integrity when fitted properly
• Can eliminate visible gaps or misalignment at the dryer outlet

• One dryer elbow part

• Disconnect power (and gas supply for gas dryers) before servicing; follow all safety warnings
• Remove the dryer from the wall enough to access the outlet; loosen or remove clamps to swap the elbow
• Use appropriate duct clamps or approved tape to secure connections; ensure vent is clear of lint

(18"- 29")