Whirlpool Range Heating Element

This surface element supplies heat to an electric range or cooktop burner. When it fails, the burner may not heat or may heat inconsistently. Replacing the element restores steady, reliable cooking performance.

• Converts electrical energy into heat for the cooking zone
• Works with the surface control (infinite switch) to regulate temperature
• Common symptoms: burner won't heat, intermittent or uneven heating, visible breaks/blistering, burnt/melted terminals
• A failed element will not glow or reach set temperature when energized

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• If your model uses a plug-in coil style: remove the drip pan, pull the element straight out of the receptacle, and inspect/replace a heat-damaged receptacle as needed
• If your model uses an under-glass radiant style: lift the cooktop, transfer any clips/limiters from the old element, and route wires exactly as original
• After reassembly, test the burner at a low setting to ensure proper operation

This surface heating element restores reliable heat to a cooktop burner. Replace a failed or damaged element to bring back even, responsive heating performance and consistent temperature control for everyday cooking.

• Converts electrical power into heat for one cooktop burner
• Common fix for a burner that won't heat or only heats intermittently
• Can address uneven heating or erratic cycling at a set temperature
• Appropriate when the element shows visible damage or burned spots

• Disconnect power at the breaker and allow the cooktop to cool completely
• Access varies by model; lifting the cooktop or removing the glass top may be required
• Handle the element carefully and avoid stressing the heating surfaces
• Move wires one at a time to matching terminals; ensure all connections are secure before reassembly

1200w. Size: 6 inch. Location: Left front, right rear, and left rear.

Restore reliable oven heat with this bake element. It produces the lower-oven heat during the Bake cycle, so replacing a failed element brings back normal preheat times and consistent, even results.

• Supplies primary heat from the bottom of the oven during Bake
• Common fix for: no heat on Bake, very slow preheating, uneven baking/browning
• Replace if the element is blistered, cracked, pitted, or has visible breaks
• Helps restore accurate, stable baking temperatures

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks; take out the element's mounting screws to free the bracket
• Gently pull the element forward; transfer one wire at a time using insulated pliers and prevent wires from slipping back
• Re-secure the bracket/screws, ensure snug connections, restore power, and test Bake

This 20-inch bake element heats the bottom of the oven cavity so food cooks and browns evenly. Replacing a failed element restores proper oven heating and baking performance. What it does

• Heats the oven's bake chamber during bake cycles
• Replaces a cracked, burned-through, or non-heating bake element
• Helps resolve symptoms like no heat from the bottom, uneven baking, or oven failing to reach set temperature
• Works with the oven's control and safety circuits to provide consistent heat

• Disconnect power to the appliance at the breaker or unplug before starting
• Access usually requires removing the oven cavity bottom or back panel
• Handle the element by its insulated areas and avoid bending or touching the bare heating surface
• Tighten terminal connections securely and verify operation with the oven empty after reassembly

The Broiler Element is an OEM part for Whirlpool ranges. It serves as the heating element responsible for the broiler function used to finish cooking and browning foods under direct heat. The broiler element allows for two-sided infrared cooking above the oven cavity.

Causes of a bad broiler element can include cracks in the ceramic coils after prolonged heating cycles, corrosion of heating coils from spills or steam, or loose or damaged connections to the power supply. 

Symptoms of a bad broiler element include:  

• Inadequate or unstable heating from the broiler 
• The broiler failing to reach desired temperatures
• "Burning" smell or smoke during broiling

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air and select Kenmore oven models.

This bake element replaces the oven's lower heating element to restore normal baking heat and even cooking results. It fits compatible electric ovens and is a direct-replacement designed for safe, reliable operation. What it does:

• Heats during bake cycles to provide consistent oven temperature for cooking and baking
• Common fix when the oven won't heat or bake function fails
• Replaces elements that are visibly damaged, blistered, or show open continuity
• Helps eliminate cold spots and uneven baking when the element is functioning correctly

• One bake element

• Disconnect power to the appliance at the breaker before starting work
• Wear gloves and allow the oven to fully cool; access is typically from inside the oven or rear panel depending on model
• Remove and replace carefully, reconnecting terminals securely and checking for proper operation before restoring regular use
• If you see damage to mounting hardware or insulation, replace those parts as needed per service instructions

This boiler is the dishwasher water-heating assembly that provides the hot wash and rinse temperatures needed for effective cleaning. Replaces a failed boiler to restore normal heating during dishwasher cycles. What it does:

• Heats water used during wash and rinse cycles so detergent can clean effectively
• Helps maintain proper cycle temperatures for sanitizing performance
• Stops working when the element fails or the boiler leaks or overheats
• Often linked to no-heat cycles, prolonged wash times, or error codes related to water temperature

• Disconnect power and water supply before starting any repairs
• Inspect for leaks and damaged connectors; replace any worn mounting hardware or seals
• Handle electrical connections carefully and follow the appliance's service manual for wiring and testing

The Surface Element is an OEM component specifically designed for Whirlpool ranges and cooktops. It provides the heating source for cookware on the stove surface.

Causes of a bad element include deterioration of insulation material over time, carbonization or damage from pans slammed onto the element, or contact with moisture. 

Symptoms of a bad element include:

• Inability to heat cookware sufficiently 
• Uneven or incomplete heating of pans placed above
• Burn marks or discoloration visible on the element
• Crackling or popping noises heard from below pans

This part is also compatible with some Kenmore, Frigidaire, and select GE range models. Proper cooking performance and safety are maintained with an OEM surface element replacement when needed.

The Coil Surface Element is a 6-inch OEM part for Whirlpool ranges. It is responsible for radiating heat from its coils to cook food positioned above the stovetop grates. 

Symptoms of a faulty coil surface element include:

• Slow or uneven heating of pots and pans  
• Hot and cold spots on cooking surfaces
• Element coils glowing dimly or not at all
• Buzzing or crackling noises coming from below cookware

Causes can be mineral deposits coating the coils over time, physical damage like bending or breaks, or standard wear of heating filaments inside. 

This genuine OEM Whirlpool part is also compatible with the electric ranges of Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and Kenmore brands.

This bake element installs at the bottom of the oven cavity to provide the primary heat during Bake. Replacing a worn or failed element restores proper preheating and consistent baking performance.

• Provides lower-oven heat during Bake cycles
• Helps maintain set temperature for even, reliable results
• Common failure symptoms: no heat in Bake, unusually long preheat times, uneven or undercooked food
• Visual indicators can include blistering, cracks, or burn-through on the element

• Disconnect power at the breaker and allow the oven to cool completely
• Remove mounting screws, gently pull the element forward, and move wires one at a time to prevent them from slipping back into the cavity
• Avoid sharply bending the new element; ensure terminals are fully seated and connections are secure
• Reinstall hardware, restore power, and test Bake

This broil heating element provides the upper-oven heat for broiling and high-temperature cooking. Replaces a failed or damaged upper element to restore broil performance and even top-heat browning. What it does:

• Produces direct top-oven heat used for broiling and finishing dishes
• Restores broil function when the upper element no longer heats
• Helps eliminate uneven browning or food that won't crisp on top
• Shows visible signs of failure such as burning, breakage, or no heat

• One broil (upper oven) heating element

• Disconnect power (unplug or switch off breaker) before starting any work
• Handle element carefully to avoid bending or damaging terminals
• Electrical connections are secure and routed clear of interior surfaces
• After installation, restore power and test broil function; replace oven light cover or insulation as needed

This oven broil element replaces a failed upper heating element to restore direct top-heat broiling for searing and browning. It provides a straight, OEM-style replacement that fits into the oven cavity and reconnects to the existing terminals. What it does:

• Heats when the oven is set to Broil, delivering direct radiant heat from the top of the oven
• Restores proper browning, searing and finishing of foods when the original element fails
• Common symptom fix: element does not glow, no broil heat, or uneven top heating
• Works as a direct replacement when the original element is visibly burned, broken, or open

• Disconnect power at the breaker or unplug the range before beginning any work
• Remove the oven racks and access screws, then carefully pull the old element forward from its terminal block
• Match terminal type and orientation before reconnecting; handle terminals gently to avoid bending

This broil element replaces the oven's top heating element to restore browning and broiling performance. It provides the heating surface used during broil cycles so food cooks from the oven top as intended. What it does:

• Heats from the top of the oven during broil cycles to brown and crisp foods
• Restores heat when the broil function produces little or no heat
• Replaces elements that are visibly burned, broken, or open
• Works with ovens that use a tubular U-shaped upper heating element

• Disconnect power to the range at the breaker or unplug before starting.
• Allow the oven to cool completely and wear gloves to avoid sharp edges.
• Remove mounting screws and disconnect element terminals; install in reverse order.
• Verify secure connections and test the broil cycle after reassembly.