Whirlpool Range Panel Parts

The Bottom Oven Panel is an OEM part for Whirlpool ranges. This panel is located at the bottom of the oven cavity, protecting the internal components and providing a smooth surface for easy cleaning.

Causes of a bad Bottom Oven Panel can include exposure to excessive heat or spills, causing warping, discoloration, or damage to the panel.

Symptoms of a bad Bottom Oven Panel include:

• Visible cracks, dents, or other physical damage
• Discoloration or surface deterioration
• Loose or dislodged panel, exposing internal components

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This burner box is the under-top housing for an electric cooktop or range. It supports the surface heating elements and mounting hardware, restoring proper element alignment, stability, and safe operation when the original housing is bent, corroded, or damaged.

• Supports and positions the surface heating elements beneath the cooktop
• Provides mounting points for element brackets and component supports
• Helps keep elements level and secure for consistent heating performance
• Common symptoms: loose or sagging elements, rattling/vibration from the cooktop area, visible warping or corrosion, difficulty fastening element hardware

• Disconnect power at the breaker before servicing
• Lift/remove the cooktop to access the burner box; sheet-metal edges can be sharp—wear cut-resistant gloves
• Transfer elements, brackets, and wiring to the new box in their original locations; take photos for reference
• Ensure wiring is routed clear of hot surfaces and all fasteners are secure before reassembly and testing

This panel forms the floor of the oven, sitting above the bake element or burner to shield it from spills and provide a smooth, stable surface. Replace a warped or damaged panel to help maintain proper heating and easier cleanup. What it does:

• Forms the oven floor above the bake element or burner
• Shields the heat source from drips and debris to help prevent scorching and odors
• Supports designed airflow and heat distribution in the cavity
• Common replacement signs: warped or dented panel, rust or chipped finish, smoke/odors from spills beneath the panel, or uneven baking results

• 1 oven bottom panel

• Disconnect power (and shut off gas supply for gas ranges) before servicing; allow the oven to cool completely
• Remove oven racks; release front fasteners or clips and lift the old panel out of the rear tabs (method varies by model)
• Seat the new panel into rear tabs, align the front edge, and secure as originally installed
• Verify the panel sits flat and clear of the bake element or burner before reassembling

This Oven Bottom forms the floor of a gas oven cavity. Positioned above the bake burner, it shields the burner/igniter from spills while providing a smooth, removable surface that helps direct heat and is easier to clean.

• Covers and protects the bake burner and igniter assembly
• Helps channel heat and airflow across the oven cavity
• Catches drips and debris; removes for periodic cleaning
• Typical failure signs: warped or rusted panel, flaking finish, burnt-through spots, or persistent smoke from baked-on spills

• Allow the oven to cool completely; wear cut-resistant gloves—edges may be sharp
• Disconnect power and turn off gas supply before servicing
• Remove racks; release rear screws or tabs per your model, lift and slide the old panel out; seat the new panel under the front lip and secure
• Restore power and gas, then verify proper fit and clearance

This is the oven bottom panel. It forms the floor of the oven cavity above the burner or heat source, helping protect internal components and provide an even, easy-to-clean surface for baking and roasting.

• Shields the burner/heat source and directs heat within the oven cavity
• Provides a stable surface for cookware and catches drips/spills
• Common fix when the oven floor is warped, rusted, stained, or damaged
• Helps if you notice hot spots, smoke from baked-on spills, or difficulty cleaning the oven floor

• Disconnect power and allow the oven to cool completely before service
• Remove oven racks; release any hold-down screws/clips securing the panel
• Lift out the old panel and set the new panel flat and fully seated
• Reinstall fasteners and racks; test for proper fit before use

Color: Stainless

This is the removable metal oven bottom for the lower oven cavity. It forms the floor above the heating components, protecting them from spills while providing a clean, even surface for baking and easier cleanup.

• Shields heating components beneath the lower-oven floor from drips and debris
• Provides a flat, durable surface inside the oven cavity
• Helps promote even heating and airflow within the oven
• Typical replacement reasons: warped or rusted panel, chipped/flaking enamel, persistent smoke/odors from burnt-on spills

• Disconnect power at the breaker and allow the oven to cool completely before service
• Remove oven racks for access
• Remove the mounting screws (often at the rear), then lift and slide the panel out
• Reinstall with existing hardware; ensure proper clearance from the heating element before restoring power

The Control Panel is an OEM part for Whirlpool ranges. As the interface between the user and appliance, the control panel is responsible for housing all of the electronic controls and display that allow for selection and monitoring of oven functions like temperature, bake time, locks, and timers.

Causes of a bad control panel can include cracked or worn buttons or displays that no longer register touch input properly. Splashing liquids or steam exposure over time can cause internal circuitry issues as well.

Symptoms of a bad control panel include:

• Unresponsive or malfunctioning buttons
• Fading or inaccurate displays
• Error codes indicating electrical faults
• Inability to properly turn elements or functions on/off

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This broiler pan is the heat-safe tray used for broiling in the oven or broiler drawer. Replace a rusted, warped, or missing pan to maintain safe broiling and simpler cleanup by catching drippings.

• Holds food for broiling and supports correct placement under the broiler
• Collects drippings to help reduce flare-ups and smoke
• Restores safe use when the original pan is rusted, pitted, dented, or warped
• Seats on the designated rails/supports in the broiler drawer or compartment per model design

• Allow the appliance to cool completely; wear cut-resistant gloves
• Remove the broiler drawer or open the broiler compartment as your model requires
• Position the pan on the proper rails/supports and verify stable seating before use
• Follow your model's user guide for broiling setup and care

This backsplash restores the rear trim behind a range or cooktop, protecting the wall and covering wiring openings for a clean, factory-look finish. It replaces a damaged, dented, or missing backsplash to improve safety and appearance. What it does:

• Covers the gap between the cooktop and the wall to block spills, splashes, and heat from reaching the wall surface
• Hides wiring and mounting holes for a neat, finished look
• Replaces bent, cracked, or corroded rear trim that can collect grease and grime
• Helps maintain proper clearance and original appearance of the appliance

• One single-piece backsplash

• Basic hardware and mounting locations are OEM-specific; confirm matching fasteners on arrival
• Turn off power to the appliance and move the unit away from the wall before removing or installing the backsplash
• Use care to avoid scratching the finish during installation; two people may be needed for larger ranges
• If mounting holes or brackets are damaged, replace those items before installing this backsplash

This heat deflector directs and shields heat inside the appliance to help protect surrounding components and maintain proper airflow. It's a simple replacement for torn, warped, or missing deflectors. What it does

• Redirects heat away from sensitive components to reduce risk of heat damage
• Helps maintain consistent airflow paths for proper appliance performance
• Commonly replaced if warped, cracked, melted, or dislodged
• May reduce odors or burning smells caused by contact with hot parts

• Disconnect power (and gas, if applicable) before beginning any repair
• Inspect surrounding mounting points and replace any damaged fasteners if needed
• Handle carefully—sharp edges may be present

This control panel assembly replaces a worn or damaged front touch/control surface and restores proper user controls and display visibility on the range or oven. Designed to match original fit and appearance. What it does

• Houses the touch buttons, display window and associated front-facing controls used to set oven functions and temperatures.
• Replaces cracked, faded, or unresponsive control surfaces that can interfere with entering settings or reading the display.
• Restores a secure, finished face for the console and helps protect internal control electronics.
• Compatible with service-side mounting and connects to the internal control board via factory wiring harnesses.

• Handle carefully to avoid scratching the finished face; use soft gloves if available.
• Disconnect power at the breaker or unplug the appliance before beginning any service.
• Installation typically requires removal of the oven/range console trim and attachment screws; keep fasteners for reuse.

This is the oven's bottom broiler pan that catches drips and supports broiling cookware for safer, cleaner cooking. It restores the oven's drip containment so you can broil and roast without excess mess. What it does:

• Catches grease and food drippings to help prevent spills and oven fouling
• Provides a stable surface for broiling pans and racks during high-heat cooking
• Helps reduce flare-ups by containing drips below the food
• Useful when replacing a worn, dented, or missing oven pan

• Allow the oven to cool and disconnect power before removing or installing the pan.
• Slide the pan into the oven bottom on the support ledges; no tools required for typical installation.
• Clean pan after each use per your oven manual to avoid heavy buildup; use non-abrasive cleaners to protect surface.
• Replace if pan is warped or damaged to ensure proper fit and performance.

Color: Stainless

This side compartment is a direct-fit door bin that restores storage on the refrigerator door, keeping bottles and small items secure and organized. Durable molded plastic replaces cracked or missing bins for reliable everyday use. What it does:

• Replaces a cracked, broken or missing door bin to restore storage capacity and organization
• Holds bottles, condiments and small containers along the inside of the refrigerator door
• Prevents items from falling when the door opens and closes
• Matches the factory shelf design for correct fit and alignment

• High-level snap-in/screw-in replacement; remove existing bin then install new bin until it seats
• Disconnect power only if removal requires working near electrical components; otherwise power disconnection is not typically needed
• Handle carefully to avoid damage to adjacent door liners or gaskets

This retainer is a small mounting clip that keeps a nearby component held securely in place, helping prevent rattles and misalignment for reliable appliance operation. Install restores proper positioning of the secured part. What it does

• Holds a component or assembly in its intended position to prevent movement or vibration
• Common symptom: loose or rattling parts near the retainer location
• Common symptom: component shifts or comes partially detached during operation
• Works as a replacement for a cracked, broken, or missing retainer that fails to secure the part

• One retainer

• Disconnect power (unplug appliance or switch off circuit breaker) before beginning any repair
• Accessing the retainer may require removing a panel or adjacent parts; keep fasteners organized
• Use basic hand tools; avoid forcing parts to prevent damage to surrounding components