Whirlpool Refrigerator Parts

Replaced a new rubber seal, it took me approx forty minutes. It works perfect, the door seals correct now. Thanks to the instruction supplied from appliance parts pros.com. Read more

Let the gaskets straighten out a bit overnight. Pulled out the old gasket, Cleaned and dried the area well though almost all the mold was in the old gasket. Pressed in the new gasket. Use a hairdryer to warm up and press the slightly deformed areas of the gasket into place. Quick and EASY. Read more

Ordered a new one. Read more

First had to clean inside the empty freezer, that was the hard part. removed old gasket and cleaned inside the track in the door. had the new gasket well warmed and in the right shape. put new gasket in track. seating it firmly. It was very easy. I did watch a couple of online videos to get the general idea of what it detailed. While I was at it I cleaned the coils with the brush I also bought with the gasket, worked great. all in all if you get organized before hand and take your time,... Read more

Noticed that the ice level LED was off then removed the ice maker and checked voltage into the ice maker module (L n' V) and didn't get power. Checked continuity on the black wire (fuse) and found it ok. Checked the parts at AppliancePartsPros.com and ordered them. Came back once got the parts. Installed the new parts then noticed that the ice maker started cycling. Read more

First replaced defrost timer. Iced up again after 2 weeks. Then replace the defrost heater. So far so good. Read more

Removed the worn gasket, cleaned the door, snapped on the new gasket. Read more

Thanks to the testimony of others on the site, I knew exactly which parts to order. The triangular holder which keeps the ice storage container was cracked so I replaced it. I also ordered a new Auger Motor Drive Shaft which makes the curvy metal piece in the bin turn. Mine had worn down and would not turn the curvy metal piece anymore. Replacing these pieces worked like a charm. My kids were amazed that ice now comes out of the door after 2 months of having to reach inside. Read more

They sent me the parts I needed. And they fit perfectly. Read more

My refrigerator was not dispensing ice. I could hear the motor activating but noticed the ice auger was not turning. My old drive shaft was stripped on both ends. Video was very helpful and it was an easy fix for someone with little handyman experience. Received my order much faster than expected! The parts arrived the next day and paid for the standard shipping charge. I live in Texas. Read more

It was not hard at all to replace our refrigerator door gasket. First I found appliancepartspros.com because I was looking up on YouTube how to do the replacement. Your video was excellent and showed me that I indeed could perform the job. I had a question about the replacement door gasket and emailed your service team at the end of the day. By next morning you had replied with the actual part number for the gasket. Shipping was fast. I had watched the video several times and so performed... Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

• Will not agitate
• Will not drain
• Won't start
• Timer will not advance

Ordered new lid switch and plunger. Watched help videos and installed new parts, Washer works like new. Read more

Replaced the actuator pad on the Whirlpool Gold Series, releasing the electronic menu pad to get to the water activator pad was the biggest hurdle. The release tabs are underneath the menu pad and you may feel as if you may break them when releasing them. They did not break but I did hold by breath. Read more

• Door sweating

Removed old gasket. Replaced old gasket with new. A small wooden block helped seat gasket. Read more

Removed the old tube. You will need this part - note that it might look different from what you have because they redesigned the part to not have a sharp curve at the bottom part where it plugs into the valve. You will also need a 5/8" stainless steel hose clamp (that will go down to 1/4") to clamp the top part of the hose that feeds into the icemaker (this replaces the factory clamp that is effectively throw-away). Read more