Whirlpool Wall Oven Parts

This Oven Bottom forms the floor of a gas oven cavity. Positioned above the bake burner, it shields the burner/igniter from spills while providing a smooth, removable surface that helps direct heat and is easier to clean.

• Covers and protects the bake burner and igniter assembly
• Helps channel heat and airflow across the oven cavity
• Catches drips and debris; removes for periodic cleaning
• Typical failure signs: warped or rusted panel, flaking finish, burnt-through spots, or persistent smoke from baked-on spills

• Allow the oven to cool completely; wear cut-resistant gloves—edges may be sharp
• Disconnect power and turn off gas supply before servicing
• Remove racks; release rear screws or tabs per your model, lift and slide the old panel out; seat the new panel under the front lip and secure
• Restore power and gas, then verify proper fit and clearance

This OEM Replacement Part is a Whirlpool-manufactured knob intended for ranges, stoves, and ovens. This part serves as a replacement for a lost, broken, or defective knob. The knob plays a crucial role in turning the stove on and off and adjusting the flame intensity from the burner head. It features a D-shaped shaft and requires no tools for replacement.

Causes of a bad knob can include wear and tear from frequent use, accidental damage from forceful turning or impact, or degradation of the internal mechanism that secures the knob to the control panel. A faulty knob can make it difficult to adjust settings or may prevent the appliance from operating correctly.

Symptoms of a bad Knob include:

• Knob not turning smoothly or slipping
• Difficulty in selecting or changing settings
• Knob falling off or not staying in place
• Cracks or visible damage to the knob

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This auxiliary surface burner head mounts over the orifice on your gas cooktop/range and distributes gas through precision ports for an even flame. Replacing a clogged or damaged head restores fast ignition and consistent heat on the small burner. What it does:

• Distributes gas through ports to produce a stable, even flame on the auxiliary burner
• Interfaces with the igniter electrode for quick, reliable lighting
• Common symptoms of a worn/clogged head: burner won't ignite or clicks without lighting; weak, uneven, or yellow flame; delayed ignition
• Helps restore proper simmer performance after corrosion, warping, or blocked ports

• 1 auxiliary burner head

• Shut off gas and disconnect power; allow the cooktop/range to cool completely
• Remove grate and burner cap, then lift off the old head; clear debris from the orifice and around the igniter (do not enlarge burner ports)
• Position the new head over the orifice and igniter; align locating features and seat fully; if your model uses screws, tighten them evenly without over-torquing
• Reinstall the cap and grate, restore gas/power, and verify even flame and normal ignition

Amperage range 3.2 to 3.6

The Knob is an OEM part for Whirlpool ranges. It is responsible for controlling oven functions through its precise movements and settings. 

Causes of a bad knob can include wear and tear over time resulting in loosening or difficult turning. Paint fading or peeling on the knob is also common. 

Symptoms of a bad knob include:

• Functions not activating when turned 
• Loose or wobbly movement when adjusting temperature or settings
• Faded, chipped, or peeling paint
• The knob coming off entirely 

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

2100W. Size: 8 inch. Location: Right front.

This top burner igniter is a genuine Whirlpool part, sold individually. This top burner igniter can be used as a replacement part in a gas range. This part fits into the surface burner orifice holder to connect to the spark module such that the gas can be turned on to heat up the burner.A top burner igniter might have to be replaced at some point in the lifespan of a gas range. A top burner igniter can be subject to damage if the connection between the igniter and the spark module is severed or is malfunctioning. The primary symptom of a malfunctioning top burner igniter is a gas burner that will not start or ignite properly. If this occurs, the top burner igniter should be removed and replaced with this genuine OEM replacement part before using that burner of the gas range again.This is an OEM part sourced directly from the manufacturer. This top burner igniter is compatible with the following appliance brands: Whirlpool, Amana, Jenn Air, KitchenAid, Ikea, and Maytag.

Restore reliable baking performance with this replacement bake element. It generates heat from the bottom of the oven to reach and maintain set temperatures, so your oven preheats properly and bakes food evenly when the original element fails. What it does:

• Supplies heat to the lower oven during Bake cycles
• Enables proper preheat and stable temperature hold
• Common failure symptoms: no heat in Bake, very slow preheat, uneven baking, element not glowing, or visible blistering/breaks

• 1 bake element

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely
• Remove oven racks; take out the element's mounting screws and gently pull the element forward to access wires
• Move wires one at a time to the new element; ensure snug, fully seated terminal connections
• Secure the element with the mounting screws, restore power, and run a brief preheat to verify operation

The membrane switch is the low-profile keypad behind your microwave's control panel. It registers button presses so you can select settings and start cooking. Replace it if keys stop responding or require excessive pressure.

• Converts keypad presses into signals for the electronic control
• Enables selection of power levels, cook times, and options
• Common symptoms: some or all keys don't work, intermittent response, must press very hard
• If the unit won't start/stop from the keypad, the membrane switch may be faulty

• Disconnect power at the breaker before servicing
• Remove the control panel to access the keypad; note ribbon orientation and routing
• Handle the flexible ribbon carefully—don't crease it—and fully seat/lock the connector

Color: brushed chrome. It measures about 2 inches in diameter.

The Surface Burner Base is an OEM part for Whirlpool ranges and cooktops. This component is a critical part of the stove's burner assembly, housing the gas outlet and providing a stable platform for the burner cap and flame spreader. It is specifically designed to handle the rigors of daily cooking, ensuring an even and controlled flame that enhances your cooking precision.

Symptoms of a failing Surface Burner Base include:

• Uneven flames or poor heat distribution
• Difficulty in lighting the burner
• Gas leaks detected around the burner area
• Visible signs of corrosion or damage to the base

Common causes for burner base issues can include continual exposure to high temperatures, spills that lead to clogging or corrosion, and normal wear and tear. 

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This control knob replaces a cracked or missing knob on your appliance's control panel. It restores positive engagement with the underlying control so you can select settings reliably and keep the front of the unit looking complete.

• Attaches to a keyed or D-flat shaft to operate the switch, valve, or timer underneath
• Allows you to choose cycles, temperatures, or burner levels as designed
• Common symptoms: knob cracked, stripped, loose/spins without engaging, falls off, or missing pointer
• Helps restore normal operation and a finished, uniform appearance

• Disconnect power; for gas appliances, also shut off the gas supply
• Pull the old knob straight off the shaft—do not pry against the bezel or panel
• Align the new knob's opening with the shaft and press firmly until fully seated
• Test the control to confirm proper engagement and function

The Knob Bezel is an OEM part for Whirlpool ranges. As a decorative cosmetic component, the knob bezel surrounds the temperature and function knobs on the oven control panel. It helps protect the knobs while enhancing the aesthetic appeal of the appliance.

Causes of a bad knob bezel include wear and tears such as scratches, dings, or cracks over time from normal use. Exposure to heat and cooking residue can also cause discoloration or warping of the bezel material.

Symptoms of a bad knob bezel include:

• An outdated or worn out appearance on the oven control panel
• Exposure of the internal knobs without cosmetic protection
• Potential interference with knob functionality from tears or cracks

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This black oven door handle replaces a cracked, loose, or missing handle and restores a secure, comfortable grip on your range. It matches the original finish and helps keep the door easy to open and close.

• Provides a sturdy handhold for opening and closing the oven door
• Replaces a handle that is cracked, broken, loose, or missing
• Helps eliminate wobble and improves door control
• Refreshes the appliance's appearance with a matching black finish

• Disconnect power and allow the oven to cool completely before servicing.
• Support the door and glass while removing inner trim screws to access the handle fasteners.
• Transfer existing end caps/mounting hardware from the old handle; align the new handle and tighten screws snugly—do not overtighten.
• Reassemble and check that the handle is secure before use.

This flame spreader sits between the burner base and cap to distribute gas evenly through the burner ports. Replacing a clogged or warped spreader restores reliable ignition and a steady, balanced flame for consistent cooking. What it does:

• Distributes gas to create an even, circular flame pattern
• Supports reliable ignition by positioning ports around the electrode
• Helps maintain proper heat output and flame stability
• Symptoms include uneven/weak flames, yellow flames, delayed ignition, or a burner that won't light

• One flame spreader

• Disconnect power and shut off gas; allow the cooktop to cool completely
• Remove grate and burner cap; lift off the old spreader (remove retaining screw if present)
• Align the new spreader over the orifice and igniter; seat fully and secure
• Do not clear ports with hard objects; use a soft brush and verify proper flame and ignition after reassembly

Note: This is a kit of 5 bezels.