Whirlpool Wall Oven Parts

The Oven Control Board is an OEM part for Whirlpool ovens. It regulates and controls the various functions and settings of your oven, including the oven's temperature, timers, and cooking modes.   

A bad oven control board can occur due to electrical malfunctions, power surges, or component failure. If you notice symptoms such as an unresponsive control panel, error codes displayed on the screen, or erratic heating and temperature fluctuations, it may be time to replace the oven control board.

Symptoms of a bad oven control board include:

• Unresponsive control panel
• Error codes displayed on the screen
• Erratic heating and temperature fluctuations

Restore your oven by replacing the faulty or malfunctioning oven control board with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This 8-inch surface burner element is the plug-in coil used on many electric ranges. Replacing a worn or failed element restores reliable heating and more even cooking performance on your stovetop.

• Provides heat to pots and pans when energized by the surface control
• Common fix for an element that won't heat or only heats partially
• Addresses visible coil damage such as breaks, blisters, or burned spots
• Corrects intermittent heating caused by an open or failing element

• Disconnect power to the range/unplug before servicing and ensure the element is cool
• Lift the old coil slightly, then pull straight out from the receptacle
• Inspect the receptacle/terminal block and drip bowl; replace if overheated or damaged
• Fully insert the new element terminals into the receptacle, seat the coil level, and test

This surface burner valve regulates gas flow to a top burner on your gas range or cooktop. The simmer version enhances low-heat control so the flame adjusts smoothly from a steady simmer to a full boil. What it does:

• Regulates gas to the surface burner as you turn the knob, controlling flame size
• Simmer variant improves stable low-flame performance at lower settings
• Common failure symptoms: burner won't light though the igniter sparks, flame won't adjust or stays at one level
• Knob feels stiff/binds or the stem no longer aligns correctly with settings

• 1 surface burner valve

• Disconnect electrical power and shut off the gas supply before servicing
• Remove the control knob and access the valve/manifold from the control panel or cooktop top
• Note the original valve's orientation for your burner position; transfer mounting hardware as needed and tighten all gas connections securely
• After reassembly, restore gas and check every joint for leaks with an approved leak-detection solution; verify proper flame and adjustment

This genuine replacement part is a door lock motor switch assembly for ovens. The door lock motor switch assembly is the part that locks the oven door. The reason it would need to be replaced is if the motor or switch has failed and is no longer able to keep the oven door locked and secured when closed. This can happen due to excessive wear and tear over time. To replace this part, start by unplugging the oven. After that, pull the oven away from the wall and proceed to remove the upper back access panel of the range. Once removed, lift the panel off and locate the lock motor and switch assembly. Disconnect the wires from the motor and switch. Once removed, unthread the two mounting screws that hold the assembly in place. Remove the connection rod. Proceed to install the new switch and motor assembly by reattaching the connection rod and refastening the mounting screws. Reattach the wires to the motor and switch and proceed to reinstall the back panel of the oven. This genuine OEM part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand ovens.

This is a glass door outer panel assembly that has been manufactured by Whirlpool for use with ovens. The glass door outer panel assembly contains everything needed to replace a broken or deteriorated door. The door needs to be in proper working order to keep heat-sealed inside the oven, as well as allow the user to easily access the oven. Over time, this part could become dented, bent, scratched, cracked, or otherwise rendered ineffective, requiring replacement. This part may require two people to install as it is heavy. Unplug the oven and allow it to cool down entirely before attempting any repairs.As a genuine OEM part, this part has been sourced directly from the manufacturer and is only sold individually. This glass door outer panel assembly is manufactured from high quality and durable materials to ensure sturdiness. It is intended for use with ovens and ranges manufactured by Whirlpool, Maytag, Kitchenaid, Amana, and Magic Chef.

Color: White

This replacement grease filter captures airborne grease and cooking residue in your appliance's venting system, helping protect the blower and ductwork while maintaining effective ventilation and airflow.

• Traps grease and food particles carried by the exhaust airstream
• Helps sustain proper airflow and reduce smoke and lingering odors
• Replace if mesh is torn, warped, missing, or remains clogged after cleaning
• Common symptoms include persistent smoke/odors, visible grease buildup, or a loose/rattling filter

• Disconnect power before servicing and allow the appliance to cool completely
• Open the filter access, release the retaining latch or screws, and remove the old filter
• Slide the new filter into place, matching the original orientation/tabs
• Ensure the filter is fully seated and secured; do not operate the unit without a filter

This oven rack restores a stable cooking surface inside the oven, letting you slide baking sheets, pans and cookware in and out safely. It replaces bent, rusted or missing racks to help your oven perform as intended. What it does:

• Provides a stable shelf for cookware and bakeware during cooking and baking
• Slides into oven rack guides to allow easy insertion and removal of pans
• Replaces warped, bent or missing racks that cause uneven cooking or instability
• Compatible with models that use part number W11256463

• Allow the oven to cool completely before installing or removing the rack.
• Slide the rack into the oven's existing rack guides until fully seated.
• Wear gloves to protect hands from sharp edges and to avoid pinching.
• Do not modify the rack or force it into incompatible guides.

This upper broil element sits at the top of the oven cavity to provide intense radiant heat for broiling and finishing. Replacing a burned-out element can restore top-heat performance and consistent, even results.

• Provides direct, high heat from the top during Broil to sear and brown food
• Common symptoms include: no broil heat, uneven top browning, only the bake element heats, visible cracks/blisters, or tripping a breaker from a shorted element
• Works with the oven control to cycle heat and maintain broil temperature
• A failed element typically shows no continuity when tested with a multimeter

• Disconnect power at the circuit breaker and allow the oven to cool completely
• Remove racks; support the element, remove mounting screws, and carefully pull it forward
• Transfer wires one at a time with insulated pliers; prevent leads from slipping back into the insulation
• Avoid bending the element or over-tightening screws; ensure terminals are fully seated, restore power, and test Broil

This front leveling leg adjusts the height at the front of your appliance to keep it level and steady. Replacing a worn or missing foot helps eliminate rocking, protect floors, and make fine leveling adjustments simple.

• Threads into the base at the front corner to raise or lower the unit for accurate leveling
• Stabilizes the appliance to minimize rocking and vibration when opening the door or using the cooktop
• Restores proper adjustment when the original foot is stripped, bent, or missing
• Common signs include a wobbling appliance, difficulty leveling, or metal-to-floor contact/scuffing

• Disconnect power; turn off the gas supply
• Protect the floor and use an assistant to carefully slide and tip the appliance
• Start the new leg by hand to avoid cross-threading; finish adjustment with a wrench
• Level front-to-back and side-to-side, then verify stability before restoring service

Spark electrode with a 29 inch female terminal.

This thermostat is a temperature-sensitive safety switch for range and wall-oven systems. It opens or closes its electrical contacts at a set temperature to help regulate heat, protect components, and keep the appliance operating safely and reliably.

• Senses temperature and opens/closes the circuit at its calibrated threshold
• Helps prevent overheating by interrupting power when excessive heat is detected
• Automatically resets once temperatures drop, depending on design and application
• Common failure signs include no heat, heat dropping out during preheat/bake, or no continuity through the thermostat when cool

• Disconnect power at the breaker; if gas, also shut off the gas supply before servicing
• Access the part per your model; photograph wiring and move connectors to the new thermostat one at a time
• Reinstall in the original orientation and location so it senses heat correctly; do not alter factory routing
• After installation, run a brief test cycle to confirm normal operation

This surface burner infinite switch controls power to an electric range or cooktop element, letting you set precise heat levels. Replacing a failed switch restores consistent heating and ensures the burner shuts off at the Off position.

• Regulates power to the surface element by cycling on and off for variable heat settings
• Interfaces with the control knob to adjust temperature from low to high
• Helps ensure the burner turns fully off at the Off position
• Common fix for a surface element that won't heat, only heats on High, won't shut off, or has erratic temperatures

• Disconnect power to the appliance before servicing
• Access the control panel, remove the knob, and unmount the old switch
• Move wires to the same labeled terminals on the new switch; transfer one at a time or use a photo for reference
• Secure the switch, reinstall the panel/knob, restore power, and test burner operation

This surface burner spark igniter creates the electric arc that lights the gas flame on your cooktop or range. Replacing a worn or cracked electrode restores reliable ignition and helps resolve hard-to-light burners and intermittent sparking.

• Provides a high-voltage spark at the surface burner to ignite gas
• Mounts to the orifice holder beneath the burner head
• Failure symptoms include burner not lighting, needing a match, or intermittent/weak spark
• Common issues: chipped/cracked ceramic insulator or damaged terminal/lead

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool; remove grates, burner caps, and heads to access the orifice holder
• Transfer the ignition lead, install the new electrode, and route the wire away from heat and sharp edges
• Ensure the tip is positioned near the burner as designed; verify spark and ignition before reassembly

The burner cap is an OEM part for Whirlpool gas ranges. It is located on the cooktop burner and helps to distribute the gas evenly, allowing for a consistent and controlled flame.

A bad burner cap can occur due to regular use, wear and tear, or accidental damage. If the cap becomes worn, cracked, or clogged, it can lead to issues such as uneven heating, weak flames, or difficulty in igniting the burner.

Symptoms of a bad burner cap include:

• Uneven heating or hot spots on cookware.
• Weak or inconsistent flames.
• Difficulty in igniting the burner.
• Visible damage or debris accumulation on the cap.

If you're experiencing any of these issues, it's time to replace the Cap-Burner with this genuine Whirlpool part for proper heat distribution and reliable ignition for your gas range. This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This electronic control board is the "brain" of the dishwasher, coordinating cycle timing and powering key components. Replacing a failed board can restore normal operation when the unit won't start, stops mid-cycle, or behaves erratically. What it does:

• Manages cycle timing and sequences based on selected options
• Distributes power to the circulation pump, drain pump, water inlet valve, heater, and dispenser
• Monitors inputs from sensors and the door switch to advance/complete cycles
• Faults can present as unresponsive controls, won't start/finish cycles, random resets, or error codes

• 1 electronic control board

• Disconnect power at the breaker before servicing; shut off water supply if accessing the lower compartment
• Use anti-static precautions; handle by the edges and avoid touching connector pins
• Access location varies by model; photograph wiring and transfer one connector at a time
• After installation, run the dishwasher's diagnostic/service cycle to verify operation