Yard Machines Lawn Mower Parts

This replacement part is a washer. It is a genuine replacement part made by MTD. Washers are small but important components, allowing spacing in between certain parts near and around the engine. Washers are typically used alongside screws and nuts to provide a tight and secure fit of many different parts in the appliance.A new washer might be needed if the current one is damaged or missing. Washers need to be replaced as they become stripped. This is usually due to friction inside the machine. Be sure the engine is turned off before replacing this part. Typically washers are easy to replace and might only need a screwdriver during the repair. This washer is a genuine OEM replacement part. Note that it is sold individually. Be sure to purchase the correct amount as some machines require more than one.

Flange bearing for lawn tractors and walk-behind mowers. Replace if you notice excessive noise, vibration, or wheel wobble. Verify fit with your model number.

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.

A ball bearing is a rolling element bearing that uses balls to maintain the separation between the bearing races. This part is designed for use with outdoor lawn and garden power equipment such as snowblowers, chippers, shredders, and tillers. It is compatible with products by brands such as Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, and MasterCut.The ball bearing part is crucial because its purpose is to reduce rotational friction while supporting radial and axial loads. Without functioning ball bearings, valuable outdoor equipment would fall apart and quickly stop working. That is why it is important to get any ball bearings replaced if they are worn out or malfunctioning.This ball bearing is made out of metal. The ball bearing is an original OEM part sourced directly from the manufacturer, MTD. It is sold individually.

Flange bearing for lawn tractors and mowers. Replace if you notice wobbling, excessive noise, or difficulty engaging blades. Verify fit with your model.

Replacement blade for chipper shredders. Chops limbs and sticks into particles. Order a new blade if yours is dull, chipped, bent, or worn from use.

Replacement 22-inch cutting blade for walk-behind mowers. Restores cutting performance when blade is dull, bent, cracked, or damaged from impacts.

Replace your dull or damaged lawn mower blade to restore clean, even cuts. This 20-inch mulching blade fits select walk-behind mowers. DIY-friendly.

This control cable is a genuine MTD part, sold individually. This control cable can be used as a replacement part in a lawn mower. The purpose of a control cable, otherwise known as a throttle cable, in a lawn mower is to allow the operator to control the speed of the mower.The control cable in a lawn mower might be subject to replacement in the event that it is damaged. This damage can manifest in the form of puncturing, fraying, tearing, ripping, eroding, or warping. If the control cable is no longer functioning, it should be removed and replaced by this genuine OEM replacement part before using the lawn mower again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement. This component is a genuine OEM replacement part sourced directly from the manufacturer. This control cable is compatible with the following outdoor appliance brands: MTD, Troy-Bilt, Craftsman, and Yard Machines.

Control cable won't engage or feels loose? This 45-inch control cable restores smooth operation on walk-behind and self-propelled mowers. Easy install.

Drive clutch cable that engages the drive belt to turn snowblower wheels. Replace if cable is frayed, stretched, or won't engage properly.

Control cable for walk-behind mowers. Connects control handle to drive or blade engagement system. Replace if cable is frayed, kinked, or broken.

Replace your worn or broken walk-behind mower control cable. This cable connects the control handle to the engine or drive system and may need replacement if damaged or frayed.

Control cable for lawn mowers. Connects handle controls to engine or drive system. Replace if frayed, kinked, broken, or won't engage properly.

Can't control mower speed or engine won't maintain RPM? Replace the throttle cable. Easy 15-minute repair restores smooth speed control on your mower.

This is a throttle body intended for use with lawnmowers and tractors. The throttle body is attached to the control cable, the throttle control wire, and the throttle lever. It can be damaged or wear out with regular use. Signs that the throttle body is failing or going bad include a very low idle or poor idle. Stalling of the machine when stopping the device is another indicator that the throttle body is bad. When this happens, a new throttle body must be installed.Replacing a throttle body is simple. It requires a set of pliers, a wrench, and a screwdriver. Always wear gloves when working on a throttle body repair. Make sure to allow time for the machine to cool completely before beginning the repair.This throttle bottle is an authentic OEM part. It is supplied directly from the manufacturer. The throttle body is made of high-quality, durable plastic material. It is sold as an individual unit. The throttle body is compatible with Huskee, MTD, Yard Machines, Yard-Man, and Cub Cadet brands. It can be installed in various machines, including push-behind lawn mowers, lawn tractors, and other lawn equipment."