Parts for Maytag LSG7800AAE: 02 - Base / Brake (Lsg7800aae) Parts

The OEM Replacement is a bearing designed to function as the rear bearing in Whirlpool front-load washers. It also works as the upper brake bearing in top-load washers. Positioned near the tub's brake assembly, this component plays a significant role in the operation of the washer. In top-load washers, it resides above the brake assembly.

Causes of a bad bearing can include prolonged wear and tear, exposure to excessive loads, or water intrusion that leads to rust and corrosion. A compromised bearing can lead to more significant issues if not addressed promptly.

Symptoms of a bad bearing include:

• Loud, unusual noises during the wash or spin cycles
• Excessive vibration or movement of the washer
• The drum not rotating smoothly or becoming stuck
• Leaks around the drum area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Brake Assembly is an OEM part for Whirlpool washing machines. This component plays a crucial role in stopping the washer drum from spinning at the end of the spin cycle. It ensures that the drum comes to a complete stop, allowing for safe unloading of laundry and preventing potential damage to the machine. Brake removal tool: TJ038315

Over time, the brake assembly can wear out or become damaged due to frequent use and the stresses of stopping a spinning drum. If the brake assembly fails, it can lead to issues with the washer’s spin cycle and overall performance.

Symptoms of a bad brake assembly include:

• The drum not stopping quickly after the spin cycle
• Loud noises or grinding sounds during or after the spin cycle
• The washer shaking or vibrating excessively
• Clothes remaining too wet after the spin cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Brake Assembly is an OEM part for Whirlpool washing machines. This component plays a crucial role in stopping the washer drum from spinning at the end of the spin cycle. It ensures that the drum comes to a complete stop, allowing for safe unloading of laundry and preventing potential damage to the machine. Brake removal tool: TJ038315

Over time, the brake assembly can wear out or become damaged due to frequent use and the stresses of stopping a spinning drum. If the brake assembly fails, it can lead to issues with the washer’s spin cycle and overall performance.

Symptoms of a bad brake assembly include:

• The drum not stopping quickly after the spin cycle
• Loud noises or grinding sounds during or after the spin cycle
• The washer shaking or vibrating excessively
• Clothes remaining too wet after the spin cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Brake Assembly is an OEM part for Whirlpool washing machines. This component plays a crucial role in stopping the washer drum from spinning at the end of the spin cycle. It ensures that the drum comes to a complete stop, allowing for safe unloading of laundry and preventing potential damage to the machine. Brake removal tool: TJ038315

Over time, the brake assembly can wear out or become damaged due to frequent use and the stresses of stopping a spinning drum. If the brake assembly fails, it can lead to issues with the washer’s spin cycle and overall performance.

Symptoms of a bad brake assembly include:

• The drum not stopping quickly after the spin cycle
• Loud noises or grinding sounds during or after the spin cycle
• The washer shaking or vibrating excessively
• Clothes remaining too wet after the spin cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Brake Assembly is an OEM part for Whirlpool washing machines. This component plays a crucial role in stopping the washer drum from spinning at the end of the spin cycle. It ensures that the drum comes to a complete stop, allowing for safe unloading of laundry and preventing potential damage to the machine. Brake removal tool: TJ038315

Over time, the brake assembly can wear out or become damaged due to frequent use and the stresses of stopping a spinning drum. If the brake assembly fails, it can lead to issues with the washer’s spin cycle and overall performance.

Symptoms of a bad brake assembly include:

• The drum not stopping quickly after the spin cycle
• Loud noises or grinding sounds during or after the spin cycle
• The washer shaking or vibrating excessively
• Clothes remaining too wet after the spin cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Brake Assembly is an OEM part for Whirlpool washing machines. This component plays a crucial role in stopping the washer drum from spinning at the end of the spin cycle. It ensures that the drum comes to a complete stop, allowing for safe unloading of laundry and preventing potential damage to the machine. Brake removal tool: TJ038315

Over time, the brake assembly can wear out or become damaged due to frequent use and the stresses of stopping a spinning drum. If the brake assembly fails, it can lead to issues with the washer’s spin cycle and overall performance.

Symptoms of a bad brake assembly include:

• The drum not stopping quickly after the spin cycle
• Loud noises or grinding sounds during or after the spin cycle
• The washer shaking or vibrating excessively
• Clothes remaining too wet after the spin cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Brake Assembly is an OEM part for Whirlpool washing machines. This component plays a crucial role in stopping the washer drum from spinning at the end of the spin cycle. It ensures that the drum comes to a complete stop, allowing for safe unloading of laundry and preventing potential damage to the machine. Brake removal tool: TJ038315

Over time, the brake assembly can wear out or become damaged due to frequent use and the stresses of stopping a spinning drum. If the brake assembly fails, it can lead to issues with the washer’s spin cycle and overall performance.

Symptoms of a bad brake assembly include:

• The drum not stopping quickly after the spin cycle
• Loud noises or grinding sounds during or after the spin cycle
• The washer shaking or vibrating excessively
• Clothes remaining too wet after the spin cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement mounting screw secures appliance panels and components to restore proper fit and reduce rattling. Use when a damaged or missing screw causes loose trim, gaps, or vibrating noises; order by part number to ensure a match. What it does:

• Fastens panels, brackets, or trim to keep parts aligned and secure.
• Stops vibration and rattling caused by loose or missing screws.
• Common symptoms: visible gaps, loose panels, hardware falling out, or excess noise.
• Use the part number and/or existing screw to ensure correct size and thread before ordering.

• Disconnect power and water before accessing internal components.
• Use the correct screwdriver or bit to avoid stripping the head.
• Turn until snug; avoid over-tightening which can strip threads or crack trim.
• Keep small parts away from children and pets during repair.

Lower brake bearing

This idler pulley guides and maintains tension on the dryer drive belt to help the drum rotate smoothly. Replacing a worn pulley restores correct belt tracking and reduces noise from rubbing or slipping. What it does

• Guides the dryer drive belt and keeps proper belt tension
• Helps the drum turn smoothly during normal operation
• Commonly used when you hear squeaking, grinding, or belt slipping noises
• Prevents premature belt wear and misalignment

• One idler pulley

• Disconnect power before starting any repair; the appliance is de-energized
• Basic hand tools required; remove the front or access panel and drum as needed per your model's service instructions
• Inspect the belt and bearing surfaces; replace belt if damaged or glazed
• Do not lubricate the pulley unless the OEM specifically directs it; replace if bearing is noisy or seized

The Pump and Drive Belt Kit is an OEM replacement part for Whirlpool washing machines. The Pump and drive belt kit is responsible for helping to drain water from the washer drum during the wash cycle. The pump and drive belt kit works by powering the washer's pump to remove water from the drum and out of the washer. The drive belt provides the power to turn the pump, while the pump helps to drain the water. The kit includes 1 pump belt and 1 drive belt.

This part fixes the following symptoms:

• Standing water in the washer drum
• Ineffective or non-existent water drainage
• Potential water damage or flooding caused by a faulty pump or drive belt

Causes of needing to replace the pump and drive belt kit include normal wear and tear over extended use, exposure to debris or foreign objects, or physical damage from impact or mishandling.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models. 

The Pump and Drive Belt Kit is an OEM replacement part for Whirlpool washing machines. The Pump and drive belt kit is responsible for helping to drain water from the washer drum during the wash cycle. The pump and drive belt kit works by powering the washer's pump to remove water from the drum and out of the washer. The drive belt provides the power to turn the pump, while the pump helps to drain the water. The kit includes 1 pump belt and 1 drive belt.

This part fixes the following symptoms:

• Standing water in the washer drum
• Ineffective or non-existent water drainage
• Potential water damage or flooding caused by a faulty pump or drive belt

Causes of needing to replace the pump and drive belt kit include normal wear and tear over extended use, exposure to debris or foreign objects, or physical damage from impact or mishandling.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models. 

A small trim screw designed to secure appliance trim pieces and molding, restoring a finished look and keeping panels held firmly in place. Ideal when a trim piece is loose, missing a fastener, or shows minor rattling. What it does:

• Fastens trim, molding, or decorative panels to the appliance frame
• Restores secure mounting and helps eliminate loose or rattling trim
• Replaces missing or stripped fasteners that cause gaps or poor fit
• Compatible with common trim attachment points where OEM screw is specified

• Disconnect power or unplug the appliance before attempting repairs
• Use the correct screwdriver bit to match the screw head to avoid stripping
• Install by hand to start threads, then tighten snugly—do not overtighten
• Verify trim alignment after installation and test that the panel is secure

This stop lug is a small, molded limiter that prevents over-travel of a moving control or mechanism in your washer, helping components stop in the correct position for consistent, reliable operation.

• Acts as a positive stop to limit movement of a mating part
• Helps maintain proper alignment and protects components from over-rotation
• Symptoms of a worn or missing lug can include excessive play, over-travel, or a control that doesn't stop where it should
• Visible damage or a missing lug indicates replacement is needed

• Disconnect power and water supply before servicing
• Access the mounting area and note the original orientation
• Seat the new lug fully and secure per the original configuration
• Reassemble and test that the mechanism stops at the intended position

Replacement lug stop that limits movement of a mechanical component to prevent over-travel and reduce wear. Restores proper stopping action so doors or internal mechanisms operate more smoothly and safely. What it does:

• Stops or limits travel of a moving part to prevent over-rotation or over-extension.
• Keeps doors, lids or internal linkages from swinging past their intended position.
• Replace if the lug is cracked, worn, broken, missing, or if the mechanism fails to stop or rattles.
• Helps prevent further damage from metal-on-metal contact or excessive movement.

• Disconnect power before starting any repair.
• Basic hand tools and access panel removal may be required to reach the mounting area.
• Inspect adjacent clips, fasteners and mating surfaces; replace any damaged hardware.

A small replacement retainer clip that secures panels, trim pieces or small hoses to prevent movement and rattling. Replaces worn or broken clips to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance trim, panels or lightweight components to the cabinet or chassis
• Prevents rattling, vibration noise and misaligned panels caused by a missing or damaged clip
• Holds wiring looms or small hoses in place on select appliance models
• Restores OEM fit where original clip has broken, bent or fallen off

• Disconnect power (and water, if applicable) before servicing the appliance
• Small part — a flat-head screwdriver or needle-nose pliers may be helpful for removal/installation
• Handle sharp edges on panels and wear gloves and eye protection as needed

The Brake Assembly is an OEM part for Whirlpool washing machines. This component plays a crucial role in stopping the washer drum from spinning at the end of the spin cycle. It ensures that the drum comes to a complete stop, allowing for safe unloading of laundry and preventing potential damage to the machine. Brake removal tool: TJ038315

Over time, the brake assembly can wear out or become damaged due to frequent use and the stresses of stopping a spinning drum. If the brake assembly fails, it can lead to issues with the washer’s spin cycle and overall performance.

Symptoms of a bad brake assembly include:

• The drum not stopping quickly after the spin cycle
• Loud noises or grinding sounds during or after the spin cycle
• The washer shaking or vibrating excessively
• Clothes remaining too wet after the spin cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.