Parts for Crosley CDE4205AZJ: 02 - Cabinet Parts

Retaining clip secures the front panel to the cabinet sides on washers and washer-dryer combos. Replace when clip is broken, missing, or won't hold panel.

Retaining clip secures the front panel to the cabinet sides on washers and washer-dryer combos. Replace when clip is broken, missing, or won't hold panel.

This outer cabinet assembly replaces the dryer's main outer shell to restore structural support and proper alignment of the drum and controls. It protects internal components and helps reduce vibration and rubbing for safer, quieter operation. What it does:

• Houses and supports the drum, motor, blower and control components
• Keeps internal parts aligned to prevent rubbing, noise or binding
• Protects electrical and gas components from debris and accidental contact
• Helps maintain proper airflow path by securing panels and seals
• Restores proper fit after dents, corrosion, or impact damage

• Disconnect electrical power (and gas supply for gas dryers) before starting any work
• Removing the top and front panels and drum may be required for access
• Handle large panels carefully; two people may be needed to avoid injury or damage
• Inspect door seals, mounting hardware and gaskets and replace if damaged

Secures panels and components in place. Replace this fastener if stripped, corroded, or missing to restore proper alignment and eliminate rattling.

Specs: 10 - 16 x .375

Spesc: #12 pozi - drive

Seals the drum edge to prevent hot air escape and reduce noise. Replace when worn to eliminate metal-on-metal sounds or clothing stains. Confirm fit.

Replace your cracked or broken dryer inner door panel to restore proper door function. Easy DIY installation in about 10 minutes. Verify fit with your model.

Double

Specs: No.8-18AB WAFER HD

Male piece. For both male and female piece use LA-1003

Secures the door latch strike to the dryer frame for reliable closing. Replace if your bracket is bent, damaged, or missing to restore proper alignment.

Single

Note: This part is one screw, order quantity needed.

Fix a sagging or misaligned dryer door that won't latch properly. This hinge restores smooth pivoting and secure closing. Simple repair in under an hour.

This hinge screw fastens a hinge to the appliance cabinet or door, helping keep the door aligned and operating smoothly. Replace a missing or stripped screw to restore solid hinge support and reliable closure.

• Secures the hinge to the cabinet/frame or door
• Maintains proper alignment at the hinge point
• Helps ensure smooth opening/closing and effective sealing where applicable
• Common symptoms: loose or wobbly hinge, door sagging/misaligned, poor closure/seal, rattling, or a missing/stripped fastener

• Disconnect power to the appliance; shut off gas if applicable
• Support the door to relieve hinge load before removing or installing screws
• Use the correct driver for your model to avoid stripping fasteners
• Start threads by hand and tighten snugly; do not overtighten

A replacement mounting screw used to secure appliance panels and components. This genuine-style fastener restores proper fit and prevents loose or rattling parts for many Whirlpool appliances. What it does:

• Fastens panels, trim, brackets, or components to the appliance frame
• Restores secure attachment when original screw is missing, stripped, or damaged
• Helps eliminate rattling, vibration noise, and loose-fitting parts
• Matches OEM fit and function when the correct part number is used

• Disconnect power (and water, if applicable) before servicing the appliance.
• Use the correct screwdriver or driver bit to avoid stripping the head; do not overtighten.
• Replace only with the exact part number to ensure correct fit; keep removed hardware organized for reassembly.

Replacement mounting screw for various appliances. Secures components and panels in place. Needed when original screws are stripped, missing, or lost.

Specs: 7/32 INCH

Replacement hex nut for dryer terminal blocks and electrical connections. Secures terminal components. Needed when original is stripped, missing, or damaged.

This terminal block connects the appliance to household power, providing a secure point for the incoming power cord wires. Replacing a damaged terminal block restores a solid electrical connection and reduces fire risk. What it does:

• Secures and organizes incoming power cord wires to the appliance's internal wiring
• Provides stable electrical contact for consistent power delivery
• Prevents loose or arcing connections that can cause intermittent power or overheating
• Common symptoms: appliance won't power on, intermittent power loss, visible burning or melted plastic at the power entry point

• Disconnect power at the breaker and verify the appliance is de-energized before starting
• Confirm wire placement and tightness; replace any scorched or damaged wiring or connectors
• Use proper tools and follow the appliance wiring diagram; tighten terminal screws to manufacturer torque if specified

Trim piece that conceals the door hinge and mounting screws. Replace your cracked, broken, or missing hinge cover to restore a clean finished look.

This factory replacement hinge screw secures the door hinge to the appliance cabinet or door. Replacing a worn or missing screw restores solid door mounting and alignment for safe, reliable opening and closing.

• Fastens the hinge securely to the door or front panel
• Helps maintain proper door alignment to prevent rubbing or sagging
• Replaces missing, stripped, or corroded hardware
• Typical symptoms include a loose/sagging door, difficulty latching, or rattling at the hinge area

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Support the door while removing and installing hinge screws
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace them together for consistent alignment

The Door Catch Kit is an OEM part for Whirlpool dryers. It includes the door catch and the necessary mounting hardware to secure it in place. This kit ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently.

Causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly.

Symptoms of a bad door catch include:

• The dryer door not staying closed
• Difficulty latching the door shut
• The dryer stopping mid-cycle due to the door opening

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: White

Dryer won't start or runs with door open? This door switch kit restores safety shutdown function. Simple clip-in repair takes 15-30 minutes. Video included.

Secures panels and components in place. Replace this fastener if stripped, corroded, or missing to restore proper alignment and eliminate rattling.