Parts for Admiral S61STRP: 02 - Controls Parts

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This mechanical rotary defrost timer controls and advances the refrigerator's defrost cycle so the evaporator periodically melts frost buildup, helping restore normal cooling. It replaces a worn or stuck timer to return automatic defrost operation. What it does

• Advances the fridge's defrost cycle on a set schedule so the evaporator heats and melts frost
• Stops the compressor during defrost so frost is removed without cooling loss
• Common symptom: excessive frost buildup on evaporator or freezer compartment
• Common symptom: refrigerator or freezer runs constantly or does not cool properly

• One defrost timer (rotary)

• Disconnect power to the appliance before starting any repair
• Locate timer (control panel, kick plate, or rear panel depending on model) and note original orientation before removal
• Remove mounting screws and electrical connector(s); install new timer in the same position and reconnect wiring

A replacement door gasket that restores a tight seal around the oven door to help maintain proper cooking temperature and improve efficiency. Fits Whirlpool ovens and ranges that use part A3189394. What it does

• Seals the oven cavity to reduce heat loss and help maintain consistent cooking temperatures.
• Helps prevent heat from escaping around the door, improving energy use and cook results.
• Worn, torn, or flattened gaskets can cause uneven baking or longer cook times.
• Replacing a damaged gasket can reduce hot spots on the exterior and nearby cabinetry.

• Disconnect power and ensure the oven is completely cool before starting.
• Remove the old gasket by pulling it out of the door channel; clean the channel before installing the new gasket.
• Press the new gasket into the channel around the full perimeter, working from one corner and ensuring an even fit.

The Door Switch is an OEM part for Whirlpool refrigerators. This switch is crucial for controlling the interior lights and the activation of certain refrigerator functions when the door is opened or closed. 

Symptoms of a failing Door Switch include:

• Interior lights staying on when the refrigerator door is closed
• Interior lights not turning on when the door is opened
• The refrigerator unexpectedly starting or stopping
• Alarms or indicators malfunctioning, signaling an open door when it is closed

Causes of a bad door switch can involve mechanical failure due to wear and tear from frequent use, damage from impacts (such as slamming the door), or electrical issues like a short circuit or faulty wiring.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Whirlpool EveryDrop Refrigerator Water Filter 7 features a coconut carbon filter that reduces contaminants to provide clean, fresh tasting water. This filter is used Whirlpool side-by-side refrigerators which accept Filter 7. Single filter. Simple, quick turn installation requires no special tools. For best performance, replace every six months. Certified to fit these leading refrigerator brands: Maytag and Jenn-Air. Micron Rating: 0.5. Filter Media: Coconut Carbon Block. Flow Rate: 0.5 GPM. Temp Range: 33 - 100 °F. Pressure Range: 30 - 120 psi. Meets NSF Standard: 42. Approved for WQA Gold Seal. Approximate dimensions: 8.25" x 8.25" x 6.5"

This refrigerator water filter bypass plug is used when you don't want to use a filter. Color: white. It measures about 3 inches in diameter.

This control wire harness connects the appliance's control board to switches, sensors and motors, restoring electrical communication for proper operation. It replaces a damaged or burned harness to help resolve intermittent or non-functioning controls. What it does:

• Provides the routed wiring and connector plugs that link the control board to components.
• Restores lost or intermittent electrical connections that can cause the unit to stop responding or display control errors.
• Replaces harnesses with damaged insulation, broken wires, or melted connectors that create faults or safety concerns.
• Ensures correct pin-to-pin connections when matched to the original harness configuration.

• Disconnect power to the appliance before beginning any repair to avoid shock or injury.
• Verify connector orientations and routing before final assembly; secure harness away from heat and moving parts.
• Use the original mounting clips/retainers or equivalent to prevent chafing; replace damaged clips as needed.