Parts for Admiral LA2000: 05 - Exterior (Rev. E-F) Parts

This lid switch actuator engages the washer's safety switch when the lid is closed so cycles can start and spin as designed. Replace a broken or missing actuator to restore proper lid switch engagement and reliable operation.

• Engages the lid switch when the lid is closed to enable agitation and spin
• A worn, cracked, or missing actuator can cause the washer not to start or to stop before spin
• Intermittent operation that changes when pressing on the lid often indicates misalignment
• Lack of an audible "click" from the lid switch can point to a faulty actuator or alignment

• Disconnect power before servicing; do not work on a live appliance
• Access the lid/switch area per your model's service procedure
• Remove the damaged actuator and install the new part, securing as designed
• Before reassembly, close the lid to ensure the switch clicks and engages properly

The Lid Hinge Pin is an OEM part for Whirlpool washing machines, that connects the machine's lid to its body, allowing for smooth and secure opening and closing. This small part ensures that the washer's lid operates correctly, maintaining proper alignment and function during use. 

Over time, lid hinge pins can wear out or become damaged due to excessive force, corrosion, or general wear and tear. This can lead to issues with the lid not closing properly, misalignment, or difficulty in opening or closing the lid.

Symptoms of a bad Lid Hinge Pin include:

• The washer lid not closing or opening smoothly
• Misalignment of the lid when closed
• Excessive play or movement in the lid when it is supposed to be secure

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This factory replacement screw fastens the specified components in your appliance as shown in the parts diagram. It restores a secure fit and helps eliminate looseness, vibration, and noise when an original fastener is missing, stripped, or corroded.

• Secures panels, brackets, and assemblies at the locations designated for your model
• Direct replacement for the original fastener to maintain proper fit and alignment
• Replace when threads are damaged, head is rounded, or rust is present
• Common symptoms: loose or rattling parts, gaps/misalignment, increased vibration

• Disconnect power and shut off water supply if applicable before servicing
• Refer to your model's parts diagram for exact location and quantity
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug firmly but do not overtighten to prevent stripping

The Lid Hinge is an OEM part for Whirlpool washers. It is responsible for supporting and allowing the smooth opening and closing of the washer lid. Fits the female end of the washer lid hinge. For the male end order WP35-2045 and if you're unable to use the old mounting screw, order WP25-7893. 

A bad Lid Hinge can occur due to regular use, wear and tear, or accidental damage. If the hinge becomes loose, bent, or broken, it can compromise the function and safety of the washer lid.

Symptoms of a bad Lid Hinge include:

• Lid not staying open or falling shut unexpectedly.
• Difficulty in opening or closing the lid.
• Visible damage or deformation of the hinge.
• Excessive movement or wobbling of the lid.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This lid switch assembly kit is the washer's safety interlock. It detects when the lid is closed so the control can allow the machine to spin, helping restore safe, reliable operation when the original switch fails.

• Senses lid closed and enables the spin cycle
• Prevents spinning with the lid open for safety
• Common failure symptoms: no spin or intermittent spin
• Requires pressing or jiggling the lid to run; no audible "click" when closing the lid

• Disconnect power before servicing
• Access the switch under the top/console area; remove the old switch/bracket as designed
• Route wiring along the original path and secure away from moving parts
• Align the actuator so the lid reliably engages the switch; test spin operation before reassembly

This lid switch assembly kit is the washer's safety interlock. It detects when the lid is closed so the control can allow the machine to spin, helping restore safe, reliable operation when the original switch fails.

• Senses lid closed and enables the spin cycle
• Prevents spinning with the lid open for safety
• Common failure symptoms: no spin or intermittent spin
• Requires pressing or jiggling the lid to run; no audible "click" when closing the lid

• Disconnect power before servicing
• Access the switch under the top/console area; remove the old switch/bracket as designed
• Route wiring along the original path and secure away from moving parts
• Align the actuator so the lid reliably engages the switch; test spin operation before reassembly

This lid switch assembly kit is the washer's safety interlock. It detects when the lid is closed so the control can allow the machine to spin, helping restore safe, reliable operation when the original switch fails.

• Senses lid closed and enables the spin cycle
• Prevents spinning with the lid open for safety
• Common failure symptoms: no spin or intermittent spin
• Requires pressing or jiggling the lid to run; no audible "click" when closing the lid

• Disconnect power before servicing
• Access the switch under the top/console area; remove the old switch/bracket as designed
• Route wiring along the original path and secure away from moving parts
• Align the actuator so the lid reliably engages the switch; test spin operation before reassembly

This factory replacement screw fastens the specified components in your appliance as shown in the parts diagram. It restores a secure fit and helps eliminate looseness, vibration, and noise when an original fastener is missing, stripped, or corroded.

• Secures panels, brackets, and assemblies at the locations designated for your model
• Direct replacement for the original fastener to maintain proper fit and alignment
• Replace when threads are damaged, head is rounded, or rust is present
• Common symptoms: loose or rattling parts, gaps/misalignment, increased vibration

• Disconnect power and shut off water supply if applicable before servicing
• Refer to your model's parts diagram for exact location and quantity
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug firmly but do not overtighten to prevent stripping

Size: 10-32

Specs: 10-16 x 1/2 inch.