Admiral Dryer Parts

• Won't start
• Timer will not advance
• No heat or not enough heat
• Touchpad does not respond

I did the recommended checks of parts as listed on the website. I would recommend as one other person did but I did not listen the first time and that is to check all the parts don't stop at the first part you find bad. As I had to make two orders paying shipping twice because I thought I found a bad part when testing the igniter but the thermal fuse was also bad and since in a different part of the machine I did not take the time to check it, bad mistake. Also one tool mentioned in the video... Read more

• Heat stays on after drum has stopped
• Will not tumble
• Touchpad does not respond
• No heat or not enough heat

Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back... Read more

• No heat or not enough heat
• Doesn't shut off
• Touchpad does not respond

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

• Too hot
• Timer will not advance
• Takes too long to dry
• Doesn't shut off

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

• Noisy

I am very glad to find the AppliancePartsPros.com website! Their instructional videos and easy parts reference made all the difference. I had originally planned to have someone come to fix my dryer, but no one was available for at least a week. I checked out their site, and after watching the videos I felt confident I could repair my appliance. I determined that a drum roller wheel had gone bad. Apparently it was going bad over the last five years since the dryer always seemed to rattle a... Read more

• Timer will not advance
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

I'm starting with a quick background on my dryer. About 18 months ago the belt on the dryer started slipping and squealing. I had a can of belt dressing spray so I popped the top open and sprayed the belt. It actually worked for about a year before it started squealing again. For the next 6 months I had to spray it more and more often. Then the clothes stopped drying. Obviously, at this point, I had to get off my lazy ass and fix the dryer. Searched my dryer's model number on the internet and... Read more

• Timer will not advance
• No heat or not enough heat
• Too hot
• Doesn't shut off

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

• Doesn't shut off
• Won't start
• Will not tumble

I realized my load of laundry was still wet after a normal drying cycle. My first action was to turn the dryer on (2010 gas Maytag centennial) and open the front port to look at the ignitor coil. It never turned orange so I knew there must be a problem with the primary circuit. I shut off the dryer, disconnected the power, pulled it away from the wall, shutoff the gas, and removed the back panel. I then disconnected the wires for the thermal fuse and checked its resistance with a multimeter.... Read more

I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more

• Will not tumble
• Takes too long to dry

I am very glad to find the AppliancePartsPros.com website! Their instructional videos and easy parts reference made all the difference. I had originally planned to have someone come to fix my dryer, but no one was available for at least a week. I checked out their site, and after watching the videos I felt confident I could repair my appliance. I determined that a drum roller wheel had gone bad. Apparently it was going bad over the last five years since the dryer always seemed to rattle a... Read more

• No heat or not enough heat
• Takes too long to dry

I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

I used the Appliance Parts Pros d.i.y. video to get some oversight on the repair; ordered the parts (heating element, Hi-Limit T-stat and Dryer Thermal Cut-Off kit). I unplugged the electric; disconnected the exhaust duct; moved the clothes dryer so that I could remove the back sheet metal panel. The electrical connection at the heater "Stacon" terminal was corroded and broken - an open circuit. This had happen about 10 years before and I was familiar with this problem. After removing the... Read more

I watched videos on the disassembly of my dryer model, and got the model number hiding on the upper dryer door jamb. After calling AppliancePartsPros.com for help, then ordered parts with the help of APP. It took almost a full day to disassemble the dryer I have, as it is a little more complicated than some models, and I went very slowly on purpose to not lose screws, or break plastic parts. Getting the wiring harness apart was the hardest thing to do, as the screwdriver shown in the video... Read more

• Will not tumble
• Noisy
• Shuts off too soon

My 12 year old Kenmore dryer problem started about 3 years ago with the motor just stopping. My thing was: I would turn it off and turn the drum by hand about halfway around and it would work again. Last month, my wife said it stopped again and its making a loud noise, but when I did "my thing" it still made a loud squealing noise (like I was killing a mouse). I made time to work on it the next day, I took it apart, using the video instructions from AppliancePartsPros, I removed the top,... Read more

• Will not tumble

I watched your initial video which gave me some insight into the repair. I removed power from the dryer and positioned it for maintenance. Since my dryer was a Maytag, I needed to remove to two front bottom Phillips screws from the front panel of the dryer prior to pulling the panel and door assy. from the unit. The top of the dryer now needs to be removed. Two screws, one on each side holds the top of the dryer in place accessible from within and under the top of the dryer. Once those two... Read more