Need Help?
Call or text
Color: gray. The back part of the knob measures about an inch in diameter, and the front part with the handle is about 2 inches in diameter.
It was very easy to repair this. All I had to do was slip on the new knob and push in. Read more
Usually ships within 4 - 14 days
Replacement idler spring for dryers. Maintains tension on the idler pulley to keep the drum belt engaged. Replace if broken, stretched, or missing.
Replacement timer control knob for washers. Restores manual cycle selection when original knob is cracked, broken, stripped, or missing. Installs on front panel.
First I used epoxy which I do not recommend since it can interfere with the later replacement of new knobs. The replacement of new knobs went easily with the exception of getting the epoxy off. Getting the epoxy off is difficult and required a Dremel to cut the plastic and slip joint pliers to peel the plastic off. Read more
Filters debris and sediment from incoming water before it reaches the inlet valve. Replace if clogged or missing to restore proper fill flow. Confirm fit.
The machine would not run a full cycle before it cut off and had the code "FE" and water was too high. The water inlet valve needed to be replaced since it was letting in too much water at time. The repair was easy. Unplug machine and turn off cold water. Remove cold water line and drain water into bucket. Remove back two braces located at the top on each end of machine This will allow you to move top cove back about one inch. Pull back top cover about 1 inch then lift off cover. Remove... Read more
Gasket sealer adhesive for dryers and laundry appliances. Bonds and seals gaskets during installation or repair. Replace when worn or missing.
Washer won't spin or stops mid-cycle? This tub displacement switch senses water level and balance to restore proper spin operation. DIY-friendly fix.
I had the problem couple years ago I bypassed unbalance switch it worked fine for a couple years and had the same problem again so ruled out unbalanced switch. Door lock light on and checked made sure wax motor pushed out all the way too the second switch for spin check OK, so took a chance on displacement switch x2. My family loves to over load it and also replaced by passed unbalance switch and boom every thing went back to normal. Its also good to clean every thing when apart. Read more
White decorative bezel that surrounds the timer control on your washer's console. Replaces cracked, broken, or missing skirts for a clean finish.
Replace your washer's cracked or worn outer tub assembly. Includes ball bearing, rear bearing, water deflector, and lip seal. Essential structural part.
Basically rebuilt the washer from the ground up. Spent more money than a new washer but we have been so happy with the way this machine has worked over the last 19 years figured it would be money well spent. Read more
Bleach not dispensing or cup cracked? This washer bleach dispenser cup snaps into the top panel. Easy DIY fix—just push down to lock in place.
Bracket assembly that secures the lid switch and thermal fuse in your washer. Replace if the mounting bracket is cracked, broken, or missing components.
This front baffle grommet cushions and secures a dryer's front baffle to reduce vibration and noise while helping keep the baffle properly positioned during operation. Fits select Whirlpool-built dryers. What it does:
This hinge kit replaces a worn or damaged refrigerator/freezer door hinge to restore proper door alignment and sealing. It helps stop door sagging and ensures smooth opening and closing for a tight temperature seal. What it does:
I figured out that the problem was the latch. I entered my model and serial #s. I chose the part that I needed and was treated to a video on how to do the job and what I would need for tool This saved me hours of trying to reason the job out on my own. Installed the part and now the washer is like new again. The new latch even came with a light bulb. I had not expect this and ordered a new bulb. But now I have a spare!! Read more
Spesc: #12 pozi - drive
Torx-head screw set secures panels and components throughout your laundry center. Replace worn, stripped, or missing fasteners to keep parts tight.
Removed the agitator, then the spacer and lock screw, then the inside tub, then the mounting stem I replaced the agitator collar to fix the issue The hardest part on this project was removing the locks with the spanner wrench. It is not easy to break loose if the machine has never been repaired in 15 years. You need the rubber hammer and really hit hard to get loose. This is what took the longest. (Approximately 1 hour for me) Read more
Injector hose and clamp kit for washers. Connects the dispenser system to deliver detergent during cycles. Replace if cracked, leaking, or worn.