Amana Cooktop Parts

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

This lower bake element supplies the primary heat for Bake cycles, restoring consistent oven temperatures and even results. Replace a burned-out or damaged element to resolve no-heat on Bake, extended preheat times, and undercooked food.

• Heats the oven cavity from the bottom during Bake cycles for proper cooking
• Restores heat when the original element is burned out or broken
• Common symptoms: no heat on Bake, very long preheat, uneven or undercooked results
• Visible damage such as blistering, cracks, or breaks indicates replacement

• Disconnect power at the breaker before servicing
• Remove oven racks, take out the element's mounting screws, and gently pull the element forward
• Transfer the two wires one at a time; do not allow wires to slip behind the oven liner
• Reinstall the element and screws, restore power, and test Bake

Color: White. For black order WPW10202217. For almond order 8522446. If your unable to use your old mounting screws order WP3196164.

This pilot burner assembly ignites the oven's main burner and restores reliable pilot flame control for gas ranges and ovens. Use to replace a worn or malfunctioning pilot that won't hold a steady flame. What it does:

• Provides the small, continuous pilot flame required to light the main burner
• Helps resolve symptoms like a weak or out pilot flame, intermittent ignition, or oven that won't light
• Direct replacement for the OEM pilot burner assembly designed for compatible gas ovens
• Works with factory gas control and ignition components when installed correctly

• Turn off gas supply and electrical power to the appliance before servicing
• Inspect the gas orifice and pilot tube for debris; clean gently if needed
• Use appropriate hand tools and tighten fittings to manufacturer torque specs — do not overtighten

This convection fan blade mounts to the fan motor and circulates hot air during convection cycles. Replacing a bent or damaged blade restores proper airflow, promoting more even temperatures and consistent baking and roasting performance.

• Mounts on the convection motor shaft to drive airflow through the oven cavity
• Helps maintain uniform temperatures for consistent convection baking/roasting
• Typical failure signs: rattling or scraping noises, visible wobble or damaged fins, weak airflow, or the fan not spinning freely
• A worn blade can contribute to uneven results in convection mode

• Disconnect power and allow the appliance to cool completely before servicing
• Access the blade behind the interior fan cover or rear panel (varies by model); note blade orientation and any spacers/washers for reassembly
• Handle sharp edges; avoid bending fins and ensure the blade spins freely without rubbing before restoring power
• For microwave/OTR convection units, high-voltage components are present.

Replace a cracked or shattered front panel with this black outer door glass for your oven/range. It restores the viewing window and finished look while helping the door seal and contain cooking heat as designed.

• Forms the exterior glass panel and viewing window of the oven door
• Helps contain heat and protect the door's insulation
• Replace if glass is cracked, shattered, deeply scratched, or discolored
• Can address a loose or rattling exterior panel after impact

• Disconnect power and allow the oven to cool completely before starting.
• Remove the door per your model's manual and place it on a padded surface.
• Transfer the handle and any trim/brackets from the old panel as required for your model.
• Wear cut-resistant gloves and eye protection; handle glass carefully and avoid overtightening fasteners.

This natural-gas orifice spud is sized for the 5K burner position on compatible gas cooktops and ranges. It meters gas to the burner to set proper flame height, helping restore consistent heat when the original orifice is clogged, damaged, or incorrect. What it does:

• Regulates gas flow for the designated burner; calibrated for the 5K position on natural gas systems
• Can help resolve weak or oversized flames, yellow/lazy flames, uneven heating, or intermittent ignition
• Required when converting back to natural gas on applicable units; not for LP gas
• Installs in the orifice holder/manifold beneath the burner head

• Shut off gas supply and power; allow the cooktop/range to cool completely
• Remove burner cap and head to access the orifice
• Use the correct nut driver; hand-start threads and tighten snugly—do not overtighten
• Reassemble, leak-check connections with soapy water, and verify flame quality per the service instructions

This charcoal filter fits an over-the-range microwave hood and absorbs cooking odors when the unit is set to recirculate indoors. Replacing a saturated filter restores effective odor control and helps keep vent airflow unobstructed.

• Absorbs smoke and odors in non-vented/recirculating installations
• Helps maintain proper vent airflow and fan performance
• Common signs it's due: lingering odors, weak vent suction, dark/discolored filter media, or a damaged/crumbly filter
• Restores intended odor-reduction performance after the original filter is saturated

• Disconnect power to the microwave before servicing
• Remove the upper grille/access panel to access the charcoal filter compartment
• Slide out the old filter; install the new one in the same orientation and seat fully
• Reinstall the grille, restore power, and test the vent fan

This safety thermostat monitors internal temperature and opens the circuit if the appliance overheats. Replacing a failed high-limit thermostat restores heat and helps protect controls, wiring, and nearby components from thermal damage. What it does:

• Monitors temperature and interrupts power to the heating circuit if an unsafe temperature is reached
• Helps prevent overheating damage to internal components
• When failed open, can cause no heat or cause the unit to shut off during high-heat operation
• At room temperature it should read closed/continuous; an open reading indicates replacement is needed

• 1 high-limit thermostat

• Disconnect power at the breaker (and shut off gas supply if applicable) before servicing
• Access location varies by model; commonly mounted to the oven cavity, plenum, or rear panel
• Transfer wires one at a time and mount the thermostat flush to its surface or bracket
• After replacement, verify proper airflow/cooling and address any root causes of overheating

The Bake Element is an OEM part for Whirlpool ranges. As a heating component, this bake element is responsible for providing bottom heat during baking and roasting functions.

Causes of a bad bake element include deterioration of insulated coils and connections from continual heat cycling. Exposure to drips or spatters can damage their integrity over time.

Symptoms of a bad bake element include:

• Inability to heat up to desired cooking temperatures
• Slow or ineffective baking and roasting results
• Error codes or failure alarms from the control board
• Visible burnouts or breaks in the coil filaments

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This broil element provides the intense top heat your oven uses for broiling. Replace a failed or damaged element to restore consistent broiler performance and proper browning when broiling meats and other foods.

• Supplies high, direct radiant heat from the top of the oven during broil cycles
• Restores proper broiling performance for browning and searing
• Replaces elements with open circuits, blisters, cracks, or shorts
• Common symptoms include: broiler won't heat, weak or uneven broiling, visible damage, or the breaker trips when broil is turned on

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely
• Remove mounting screws, gently pull the element forward, and disconnect wires; support wires so they don't slip back into the rear cavity
• Attach wires to the new element and secure with existing screws; avoid bending the element or overtightening
• Restore power and test the broil function

This is a control knob for a range/cooktop. It lets you turn the burner valve shaft to adjust flame or heat settings. A worn or cracked knob can slip, sit crooked, or fail to turn the control smoothly.

• Replaces a damaged or stripped knob so settings engage properly
• Common symptoms: knob cracks, loosens, wobbles, or won't turn the valve shaft
• Restores clear pointer alignment and tactile click/feel during adjustment

• Disconnect power and allow all surfaces to cool before servicing
• Pull the old knob straight off the valve shaft; align the new knob's D-shape/flat with the shaft and press firmly
• Do not force—verify the knob matches the shaft style and location
• Test each control for smooth movement and correct alignment after installation

This control knob attaches to the control shaft and lets you select settings on your appliance. If the knob is cracked, stripped, or missing, replacing it restores smooth turning and accurate setting selection.

• Provides a secure grip to turn the control shaft and choose temperature, cycles, or levels
• Replaces knobs that are loose, cracked, or spin without turning the control
• Restores proper alignment of the pointer with the panel markings
• Helps resolve "won't stay on a setting" complaints caused by a stripped insert

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Pull the old knob straight off; transfer any adapter or clip if present
• Align the flat/spline opening with the shaft and press straight on—do not force
• The pointer lines up with the panel and test operation

This oven bake burner is designed for Direct Spark Ignition (DSI) ranges. It channels gas from the bake orifice and distributes an even flame under the oven floor for consistent baking performance and reliable light-off during the bake cycle.

• Distributes gas through burner ports to create an even bake flame
• Works with the DSI spark electrode to ignite the bake flame
• Can address uneven or weak flame patterns and delayed ignition in bake

• Disconnect power and shut off gas; allow the oven to cool completely
• Remove the oven bottom and flame spreader to access the burner
• Transfer any reusable mounting hardware or shields from the original burner
• After reassembly, restore gas/power and leak-test any disturbed gas connections per local code

This spark module supplies the high-voltage pulses that ignite the surface burners on compatible gas cooktops/ranges. Replacing a failing module restores consistent burner spark and reliable lighting when you turn the knobs.

• Distributes ignition voltage to multiple burners; coordinates spark when a burner is turned on
• Common failure symptoms: no spark on any or multiple burners, intermittent clicking, or burners that won't ignite despite gas flow
• Click continuously if internal circuitry fails or senses a short in the ignition system

• Disconnect power and shut off gas before servicing; verify no residual voltage
• Label and transfer each spark wire and connector one at a time to maintain correct routing
• Mount securely and avoid pinching or stretching ignition leads
• If burners still won't spark after replacement, inspect electrode wires, switches, and grounds

This 8-inch surface burner element delivers heat on an electric cooktop or range. Replacing a worn or open element restores even heating on the burner zone and reliable response to temperature settings.

• Heats the 8-inch cooking zone when the surface control is turned on
• Helps maintain consistent pan temperature for boiling, simmering, and frying
• Common symptoms: burner won't heat, heats unevenly or intermittently, visible blistering/breaks in the coil, or scorch marks at the terminals
• Replacing a damaged element can prevent further damage to the receptacle/terminal block

• Disconnect power at the breaker and allow the unit to cool completely
• Handle the element by the bracket; avoid bending the coil
• For plug-in setups, pull the old element straight out and firmly seat the new one; for wired connections, move wires one at a time to the matching terminals and secure properly
• Inspect the receptacle/terminal block and wiring; replace if burnt or loose before restoring power