Amana Dishwasher Pump

The Impeller is an OEM part for Whirlpool brand dishwashers. Located within the dishwasher sump assembly, this plastic component utilizes rotating blades to circulate wash water throughout cycles.

Causes of a bad impeller can include cracking or damage from minerals over time, chunks of food debris jamming the blades, or normal wear on plastic.

Symptoms of a faulty impeller include: 

• Inadequate water circulation yielding poor cleaning 
• Food particles or utensils not fully rinsed
• Loud clicking or grinding noises mid-cycle
• Error codes relating to low water pressure

Replacing the impeller restores optimum water flow for Whirlpool dishwashers. Proper circulation using the OEM replacement ensures all portions of dishes and cycles receive sufficient water volume. Compatibility also includes Maytag, Jenn-Air, Amana, Magic Chef, and other brands.

Pump housing only. For a complete pump and motor assembly, order WPW10247394.

This dishwasher circulation pump and motor drives wash water through the spray arms for effective cleaning. Replacing a failed wash motor restores strong spray pressure and consistent cleaning performance throughout the cycle.

• Circulates water through the spray arms to wash and rinse dishes
• Maintains proper flow and pressure from the sump to all spray arms
• Direct replacement for a seized, noisy, or non-running wash motor
• Common symptoms: poor cleaning, no spray action, or humming/buzzing during wash

• Disconnect power at the breaker and shut off water supply before servicing.
• Access is from the bottom/front; many models require removing the toe panel and/or sliding the dishwasher out.
• Connect the wiring, seat the pump seal fully in the sump, and lock the assembly in place per your model's procedure.
• After reassembly, run a brief fill-and-wash to check for leaks and proper spray action.

The Volute with Seal is an OEM part for Whirlpool dishwashers. This part directs water flow within the dishwasher's pump, ensuring efficient circulation and pressure during the wash cycle. The seal helps to prevent leaks by maintaining a tight closure between the volute and other pump components.

Common causes of a bad volute with seal include wear and tear from regular use, damage from debris or hard water deposits, and seal degradation due to age or chemical exposure.

Symptoms of a bad Volute with Seal include:

• Water leaking from the pump area
• Decreased washing performance
• Unusual noises from the pump during operation
• Visible cracks or damage to the volute or seal

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement part is a dishwasher pump and motor assembly. The dishwasher pump and pump motor circulate water through the dishwasher's spray arm. When the spray arms aren't spraying properly, this could mean that it's time for a new pump and motor assembly. Luckily replacing this part is a relatively simple process.Start by making sure the dishwasher is unplugged. After that shut off the water supply going to the dishwasher. Then disconnect the drain line from the garbage disposal or sink drain. Open the dishwasher door and pull out the bottom dish rack. Remove the upper dishrack from its track. Release the spray arm on the bottom of the washer. Then proceed to release the feed tube clips. Using a nut driver remove the bottom access panel and tow panel. Pull them out to remove them. Remove the power cable from the junction box, and disconnect the supply line from the inlet valve. Proceed to pull the dishwasher out of the counter. Tilt the dishwasher on its side and pull the hose from the drain pump. Remove the wire harness from the pump. Disconnect wires from diverter motor and circulation motor. Once complete, proceed to tilt the dishwasher upright and remove the pump and motor assembly from the bottom of the dishwasher. Replace with the new assembly.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

This chopper assembly replaces the food-chopping component in compatible countertop food processors, restoring even chopping and diced results. It helps get blades turning and keeps food processing performing as intended. What it does:

• Spins and chops food inside the processor bowl for consistent results
• Restores proper cutting when chopping is uneven or not happening
• Helps eliminate food buildup that causes noisy or inefficient operation
• Works with the existing drive coupling to transfer motor power to the blades

• Disconnect power and remove the processor bowl and lid before servicing
• Handle blades carefully — they are sharp; wear cut-resistant gloves
• Ensure the part seats fully on the drive coupling and locks into place before use
• Test operation with small amounts of food after reassembly; stop immediately if unusual noise or resistance occurs

Seal not included