Amana Gas Conv Kit Parts

The LP Conversion Kit is an OEM component for Whirlpool and KitchenAid gas dryers. It allows conversion from natural gas to liquid propane fuel operation. Over time in gas-powered dryers, improper gas/air mixture causes part wear like weakened burner components. This is risky if overlooked but converting to an alternative fuel safely remedies. 

Causes relate to unavoidable deterioration from gas combustion stresses. Conversion using this kit prevents hazardous gas leaks or explosions.

Symptoms involve:

• Diminished or unsafe heat levels from burners
• Gas leaks which exacerbate safety risks over time

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Whirlpool LP gas conversion kit is an OEM replacement part responsible for allowing the conversion of a natural gas-powered dryer to operate on LP (liquid propane) gas. This kit contains the orifice, leak limiter, and an instruction sheet to guide the conversion process. Once the conversion kit is installed, it alters the fuel source of the dryer, allowing it to burn LP gas instead of natural gas. This conversion is necessary when a home or installation site lacks access to natural gas and relies on LP gas as the fuel source for heating appliances

Causes for needing an LP gas conversion kit include relocating the appliance to a home with LP gas, or preferring LP gas over natural gas for cooking efficiency or availability. The conversion process involves changing the orifices and adjusting the gas pressure to suit LP gas requirements.

Symptoms that indicate a need for conversion or issues with the current setup include:

• Improper or uneven flame on the burners
• Difficulty in lighting the burners
• Burners not operating at full power
• Gas smell indicating possible leaks or incorrect gas type

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The LP Conversion Kit is an OEM part for Whirlpool dryers. It allows the dryer to be converted from natural gas to liquid propane (LP), ensuring safe and efficient operation with LP fuel.

Causes of needing an LP conversion kit can include relocating to an area where only LP gas is available or choosing LP gas due to its efficiency and lower environmental impact. It is essential to use the proper conversion kit to avoid potential safety hazards and ensure the dryer operates correctly.

Symptoms indicating the need for an LP conversion kit include:

• Moving to a location with only LP gas availability
• Decision to switch from natural gas to LP for efficiency or environmental reasons

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The LP Bake and Broil Kit is an OEM replacement part for Whirlpool ranges. It is a kit containing everything needed to convert the oven from Natural gas to LP.

Causes of a bad bake/broil system can include cracks, leaks, or corrosion in gas lines that produce unsafe flames over time. Pilot lights may fail to light consistently.

Symptoms of failures include:

• Inability to ignite bake/broil burners
• Erratic or intermittent baking temperatures
• Uneven cooking due to improper burner positioning
• Strong gas or chemical smells from the oven

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The LP Orifice Kit is an OEM part for Whirlpool gas ranges. It contains a set of five orifices designed specifically for use with liquid propane (LP) gas. Note: For the oven orifices, on some models they are adjustable and some they are not. Refer to parts list for your model when oven orifices are needed. LP orifice kit includes 5 orifices.

Causes of a bad LP Orifice Kit may stem from incorrect orifice size for the specific LP gas supply, wear or damage to the orifices over time, or improper installation.

Symptoms of needing to replace the LP Orifice Kit can include:

• Uneven heating or incomplete combustion of the burners
• Yellow or flickering flames instead of a steady blue flame
• Reduced cooking performance or inefficient heating

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This LP conversion kit adapts select gas cooking appliances to operate on liquid propane. Use it when installing a natural-gas model on an LP supply to ensure proper ignition, flame characteristics, and safe performance. What it does

• Converts a natural-gas appliance for use with LP/propane per the model's installation instructions
• Provides correctly sized LP components to achieve proper flame size and combustion
• Helps prevent issues such as yellow flames, sooting, and poor simmer control caused by incorrect gas type
• Required when installing where only propane is available; model-specific kit

• One LP conversion kit

• Conversion must be performed by a qualified gas technician; follow all local codes
• Shut off gas and electrical power and allow all components to cool before servicing
• Replace the specified parts and set the pressure regulator for LP; adjust low flames/air shutters as directed in the service/installation manual
• Leak-test all connections and apply conversion labels after completion; verify flame quality

For Use With LP

This orifice spud meters gas to a burner on your range or cooktop, setting proper flame size for efficient, even heating. Replacing a damaged or incorrect spud restores consistent burner performance and flame quality.

• Meters gas flow through the burner orifice to control flame height and shape
• Supports efficient combustion and consistent heat output
• Common fix for flames that are too high/low, yellow/sooty, or uneven
• Used when setting up or converting a model for the specified fuel type (LP or natural), per the position of each burner

• Shut off the gas supply and disconnect electrical power before servicing
• Remove the burner cap and head to access the spud; lift the cooktop or open the range top if required
• Remove/install with a properly sized wrench; do not overtighten. Apply thread sealant only if specified by the manufacturer
• Match each spud to the correct burner and fuel type per your model documentation; after reassembly, restore gas and leak-test with a soapy-water solution

This orifice spud meters gas to the burner for a consistent, correctly sized flame. Replace a clogged or damaged spud to restore proper burner output and reliable ignition on your gas cooktop or range.

• Controls and meters gas flow through a calibrated opening to the burner
• Helps ensure proper flame size and color when matched to the correct burner and fuel type
• Common symptoms of a failing or clogged spud: weak or uneven flame, yellow tipping, or delayed ignition
• Damaged threads or a stripped orifice can prevent correct sealing and fuel delivery

• Shut off gas supply and disconnect power; allow the appliance to cool
• Access the orifice holder/manifold for the affected burner; remove the old spud with an appropriate orifice wrench or nut driver
• Start the new spud by hand to avoid cross-threading; tighten snugly—do not overtighten brass threads
• Restore gas and check for leaks with an approved leak-detection solution; verify flame quality and adjust per the service manual

This LP gas conversion kit lets compatible gas ranges be converted from natural gas to LP (propane), supplying the correct orifices and settings so burners run safely and produce expected heat on LP fuel. What it does:

• Replaces factory burner orifices and related fittings to match LP fuel pressure and flow.
• Helps restore proper flame size and burner performance after switching from natural gas to propane.
• Addresses symptoms such as weak or yellow flames, uneven heating, or reduced burner output after fuel change.
• Intended for use only on ranges specified by the manufacturer for this conversion kit.

• Shut off the gas supply and disconnect power before beginning work.
• After installation, perform a leak test and verify correct flame characteristics on all burners.
• Keep original parts and the instructions for future reference and warranty requirements.

This conversion kit provides the orifices and instructions needed to convert a compatible gas range/oven from natural gas to liquid propane, restoring proper fuel flow and safe burner operation after a fuel-type change. What it does:

• Replaces factory natural-gas orifices with LP orifices sized for propane fuel
• Helps restore correct flame height and even heating when switching to LP
• Addresses weak or irregular flames that occur after changing fuel types
• Ensures burners receive the proper fuel jetting for safe LP operation

• Installation should follow OEM instructions exactly
• Turn off gas supply and electrical power before beginning work
• Use proper leak testing after installation and before returning the appliance to service
• Regulator adjustment or replacement may be required per OEM service instructions

This conversion orifice spud kit contains three precision orifice spuds used to change the gas flow profile for compatible cooktop/oven burners. It helps restore correct burner flame size and performance after a fuel-type conversion. What it does:

• Replaces worn or incorrect orifice spuds to set proper gas flow for burner operation
• Used in fuel-type conversion to match burner jets to the correct gas pressure/type
• Can resolve uneven or weak flames and burners that won't reach expected heat
• Works with each burner where a standard orifice spud is specified

• Turn off gas supply and disconnect power before servicing; follow all safety procedures
• Installation may require burner removal and a proper wrench or driver for the spuds
• After installation, check all fittings for leaks using a gas leak detector or soapy water

This orifice spud controls gas flow to a stove or range burner so the flame lights reliably and burns evenly. It's a small but critical gas-delivery fitting for proper burner performance. What it does:

• Directs and meters gas from the valve to the burner for a steady flame
• Restores normal ignition when a damaged spud causes weak or uneven flames
• Helps correct burners that stay low or fail to sustain a flame
• Works with the burner and valve assembly to maintain consistent heat output

• Turn off gas supply and power to the appliance before servicing
• Replace only with the exact part number or verified equivalent for safe operation
• Thread by hand then tighten to manufacturer torque—do not overtighten
• After installation, check for leaks with a safe leak-detection method;