Parts for Frigidaire FFEF3054TBK: Backguard Parts

Protective cover that shields the range door hinge assembly from debris and damage. Replace if cracked, broken, or missing to restore a clean finished look.

This is a replacement door switch that signals the appliance when the door is closed so the unit will start or run. Restores proper door-sensing function for safe, reliable operation. What it does:

• Detects whether the door is closed and sends the on/off signal to the appliance control.
• Prevents operation when the door is open; stops cycles or disables functions if faulty.
• Commonly replaces a worn, broken, or non-responsive door actuator switch.
• Symptoms of a failing switch: appliance won't start, stops mid-cycle, or control behaves inconsistently.

• Disconnect power (unplug appliance or shut off the circuit) before attempting replacement.
• Handle electrical connectors carefully; match wiring and terminal positions during reassembly.
• Verify part compatibility with your model before installation.

Signals when your range burners or oven are active. Replace when light fails to illuminate or stays on constantly. Confirm fit with your model number.

Burner cap for electric and gas ranges. Covers the burner assembly on your cooktop. Replace if cracked, chipped, discolored, or missing for proper fit.

Small protective cap covers exposed range hardware to keep out dirt and moisture. Replace if cracked, broken, or missing to restore a finished look.

This control panel is the exterior console that houses drawer controls and user interface elements, restoring a clean, functional front for your appliance. It replaces a cracked, faded, or damaged console and improves button access and appearance. What it does:

• Covers and protects electronic controls and display components from spills and wear
• Restores tactile button access and clear labeling for normal operation
• Helps stop drafts or debris from entering the control area when damaged
• Common symptom: cracked, warped, discolored, or otherwise damaged console surface

• One control panel (main console) as shown

• Disconnect power to the appliance before beginning any work
• Removal may require removing trim screws or clips; keep fasteners for reassembly
• Handle carefully to avoid scratching painted surfaces or damaging mounting tabs

This control panel houses the oven's user interface and provides the buttons and display used to set cooking modes, temperature and timers. Replacing a damaged panel restores normal user control and display readability. What it does:

• Provides the button pads and display mounting for setting oven functions and times
• Routes user inputs to the oven's control board for processing
• Failsafe symptoms: unresponsive buttons, faded or cracked face, or a display that is dim or unreadable
• Useful for restoring normal operation when the panel is physically damaged or worn

• Disconnect power at the breaker or unplug the appliance before beginning
• Handle the panel carefully to avoid scratching the display or damaging button contacts
• Some models may require removal of trim or bezels; keep fasteners organized for reassembly

White protective overlay for range control panels. Shields touch controls from scratches, spills, and wear. Replace if cracked, bubbled, or peeling.

Black touch pad overlay for range control panel. Replaces cracked, worn, or peeling overlays with faded labels. Installs directly over control board.

Oven won't heat, overheating, or controls unresponsive? This range control board manages temperature and cooking functions. Moderate DIY repair.

The Rocker Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for turning the interior oven light on and off. The light switch allows visibility of the oven cavity for viewing food during the cooking process.

Causes can include normal wear and tear over time, exposure to heat inside the oven cavity, or accidental damage.

Symptoms of a bad oven light rocker switch include:

• The oven light failing to illuminate when the door is opened
• The light remaining on even when the door is closed
• An inconsistent or flickering oven light
• The switch itself becoming loose, cracked, or non-responsive

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Switch Rocker is an OEM part for Frigidaire ranges. This switch is used to control various functions of the range, such as turning on heating elements or activating specific cooking modes. It provides a reliable and straightforward interface for managing the range's features.

You should replace the range switch rocker if it becomes faulty. Causes of a bad switch rocker can include wear and tear from frequent use, exposure to high temperatures, electrical malfunctions, or physical damage from impacts or mishandling. A defective switch rocker can result in unresponsive controls, making it challenging to operate the range effectively.

Symptoms of a bad Range Switch Rocker include:

• The switch not responding when pressed
• Inconsistent or flickering performance of the heating elements
• Physical damage or looseness in the switch
• Intermittent operation or complete failure to activate the desired function

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Insulation pad installs between range components to dampen sound and reduce heat transfer. Replace if worn, torn, or missing to restore proper insulation.

Snap-in plug cap seals unused cabinet or component openings on your range. Replace if cracked, missing, or worn to keep out moisture and debris.

White control knob for electric range burner and temperature adjustment. Replace if cracked, broken, worn, or missing. Installs on control panel.

Black control knob for range surface element switches. Replace if cracked, broken, or worn from heat exposure. Attaches directly to switch shaft for easy setting adjustment.

Indicator light lens covers and protects the burner signal light on your range. Replace when cracked, discolored, or missing. Confirm fit with your model.

Top burner won't cycle temperatures or respond? This range burner control switch restores reliable heat regulation. Direct-fit replacement for electric and gas ranges.

Burner stuck on high or won't heat? This surface element switch controls temperature for electric range burners. DIY repair in under 30 minutes.

Burner won't turn off or stuck on high? This surface element switch controls heat settings for large burners. Moderate DIY with panel removal.

Replace a cracked, broken, or missing shield on your range. This protective guard component installs to safeguard internal parts from damage or wear.

Hearing rattling noises or concerned about exposed wiring? This protective shield guards internal range components from debris and contact. Simple DIY fix.

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.