Parts for Ge DBB5000GF0GG: 01 - Backsplash, Blower & Motor Parts

Replacement timer knob for dryer control panels. Installs on the timer shaft to set drying times and select cycles. Order if original is cracked or broken.

Mounting screw for refrigerators, dryers, and washers. Replaces lost, stripped, or corroded screws during repairs or part installations.

This switch trim is a factory replacement trim piece that restores the appearance around the control switch and helps keep the area sealed from food and moisture. It provides a clean, finished look for compatible ranges and cooktops. What it does:

• Replaces a cracked, chipped or discolored switch trim to improve appearance
• Covers the switch area to help limit debris from contacting the switch assembly
• Fits the original switch opening and aligns with factory mounting points
• Works with the control switch assembly to maintain the original fit and finish

• One switch trim piece as shown

• Remove power to the appliance before starting any repair to avoid shock or injury
• Typically installs with a few screws or clips; reuse original fasteners unless replacements are provided
• Handle part carefully to avoid scratching the finish during installation

Protective plastic housing that secures the dryer control board. Replace if cracked, broken, or missing to properly support and shield electronics.

Support plate that mounts behind the dryer console to secure the electronic control board. Replace if cracked, broken, or missing to properly reinstall control.

Dryer won't start or starts automatically? Failed rotary start switch is likely. DIY repair in 5-10 minutes with basic tools. Video guide included.

The Knob Clip is an OEM part for GE washing machines and dryers. This small but crucial component is designed to secure the control knob to the appliance's control panel.  

Over time, knob clips can wear out or break due to frequent use or accidental damage. When this happens, the control knob may become loose, fall off easily, or fail to engage the control panel properly, making it difficult to set the appliance to the desired cycle or function.

Symptoms of a bad Knob Clip include:

• The control knob is loose or falls off the panel easily.
• Difficulty in adjusting settings due to a loose knob.
• The knob does not stay in place or slips when turned.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a threaded fastener used to secure panels and small assemblies on compatible appliances, restoring a tight fit and stable operation. It replaces missing or stripped screws to reduce vibration and rattling. What it does:

• Secures trim, panels, and internal components where an 8-18 thread screw is specified
• Restores proper alignment to reduce rattles or vibration caused by loose parts
• Replaces missing or damaged screws that prevent parts from fastening correctly
• Works wherever an 8-18 x 7/16 screw is required by the manufacturer

• Use the correct screwdriver or nut driver to avoid cam-out and stripped heads
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power and remove any panels per manufacturer instructions before servicing
• If threads are damaged, replace the mating fastener

Replacement screw for securing dryer components like drum supports, panels, and housings. Needed when screws are lost, stripped, or damaged during repair.

Fix a dryer that won't cycle wrinkle care properly with this wrinkle care on/off switch. Simple 5-minute installation for most DIYers. Restores function.

Dryer won't shut off in auto dry or only heats on one setting? This temperature switch restores proper heat level control. DIY-friendly repair.

Dryer won't shut off or timer won't advance? This mechanical timer controls cycle timing and program selections. Restores proper cycle operation.

Mounting screw for dryer installation and assembly. Replace this hardware if stripped, missing, or damaged during dryer maintenance or repair work.

Secures the blower wheel to the motor shaft. Replace when the wheel loosens or moves, causing rattling or rubbing noise. Includes clamps and screw.

Secures the blower wheel to the motor shaft. Replace when the wheel loosens or moves, causing rattling or rubbing noise. Includes clamps and screw.

If your dryer won't heat properly or makes squeaking noises, the blower wheel may be worn or damaged. Moderate DIY repair that restores air circulation.

Secures the drive motor to its mounting bracket. Replace if cracked, broken, or missing to keep the motor and blower aligned and stable during operation.

Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.

Metal bracket that secures the dryer motor and blower assembly in place. Replace if your mounting bracket is cracked, broken, or causing loose components.

Transfers power from motor to drum in your dryer. Replace if squeaking, not spinning, or visibly worn. Confirm fit with your model number before ordering.

Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.

Maintains tension on your dryer's drive belt. Replace if pulley is cracked, worn, or making noise. Installs inside drum assembly for smooth operation.

Seals the blower-to-exhaust duct connection in your dryer. Replace if torn, brittle, or causing heat loss and longer dry times. Confirm fit by model.

Replaces a cracked, rusted, or disconnected exhaust duct that routes hot air from your dryer to the home vent. Restores proper airflow and venting.

Dryer won't heat, overheats, or shuts off mid-cycle? A faulty cycling thermostat often causes these issues. Easy DIY fix with our video guide.

Hex washer-head screw secures dishwasher brackets, shields, and panels. Replace stripped, missing, or damaged screws to restore tight fit and stability.

Replacement mounting screw for dryer panels and components. Needed when original screws are stripped, missing, or damaged during repair or maintenance.

This motor plate is the stamped metal mounting plate that secures the motor assembly and keeps it aligned for smooth operation. It restores proper motor positioning and reduces vibration-caused noise or wear. What it does:

• Provides a stable mounting surface for the motor assembly
• Maintains motor alignment to ensure smooth shaft rotation
• Helps reduce excess vibration and noise from a loose or damaged motor support
• Supports related components so belts and pulleys track correctly

• Disconnect power before starting any repair to avoid shock or injury
• Installation requires basic hand tools and access to the motor compartment
• Verify motor and surrounding hardware are undamaged; replace any worn fasteners

Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.

Hex washer-head screw secures dishwasher brackets, shields, and panels. Replace stripped, missing, or damaged screws to restore tight fit and stability.

Factory replacement screw for securing dryer panels, brackets, and components. Restores lost or loose hardware to eliminate rattling and ensure proper fit.

Replacement screw secures dryer panels, brackets, and internal components. Replace stripped, lost, or damaged screws to eliminate rattles and maintain assembly.

Dryer won't start or hums but drum doesn't turn? This drive motor powers the drum and blower. Moderate DIY repair with video guide available.

Dishwasher won't start or runs intermittently? A faulty door interlock switch prevents operation when the door latch fails. DIY repair in 20 minutes.