Parts for Ge GTD65EBSJ3WS: Backsplash, Blower & Motor Assembly Parts

If your dryer won't start, buttons are unresponsive, or the display is blank, the control panel may need replacement. Moderate DIY repair with basic tools.

This knob assembly replaces a worn, broken, or missing control knob so you can reliably select heat or settings on your range or cooktop. It restores safe, accurate user control and a finished appearance. What it does:

• Fits onto the control shaft to allow turning the switch for burner/oven settings
• Restores tactile grip and clear position selection when the original had stripped or cracked
• Helps stop slipping or intermittently losing contact between the user and the control
• Suitable for use where the original knob assembly is damaged or missing

• Disconnect power (or turn off gas appliance supply) before servicing controls.
• Push the knob straight onto the control shaft until fully seated; pull straight off to remove.
• Inspect the switch/shaft for damage; replace the switch or shaft if the knob does not seat securely.

Fix a dryer that won't start, has a blank display, or stops mid-cycle. This main control board regulates cycles, temperature, and timing functions.

Back panel assembly for your dryer. Covers and protects internal components at the rear of the unit. Replace if cracked, damaged, or missing.

Secures dryer panels and internal components to the cabinet frame. Replace if screw is stripped, missing, or loose to prevent vibration and rattling.

Replace a cracked, worn, or missing washer in your dryer. This small hardware component ensures proper spacing and tension between parts during operation.

8-18 hi/lo 5/8

The Blower Wheel is an OEM component specifically designed for GE dryers. It is responsible for circulating air during the drying cycle, directing airflow through lint and clothes to remove moisture. The plastic blades of the blower wheel push air through the dryer and out the vent when the motor is running. 

Symptoms of a bad blower wheel include:

• Slow or inefficient drying times even on low moisture loads    
• Strange noises from inside the dryer cabinet      
• Excessive vibrations felt through the dryer door or cabinet
• Bent or cracked blower wheel blades

Causes can include normal wear and tear over time, accidents that damage the blades, or failures in the secure mounting of the blower wheel.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

Secures the drive motor to its mounting bracket. Replace if cracked, broken, or missing to keep the motor and blower aligned and stable during operation.

Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.

Metal bracket that secures the dryer motor and blower assembly in place. Replace if your mounting bracket is cracked, broken, or causing loose components.

Transfers power from motor to drum in your dryer. Replace if squeaking, not spinning, or visibly worn. Confirm fit with your model number before ordering.

Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.

Idler pulley for dryer drum assembly. Maintains belt tension to enable smooth drum rotation. Replace if worn, cracked, or causing noise during operation.

Seals the blower-to-exhaust duct connection in your dryer. Replace if torn, brittle, or causing heat loss and longer dry times. Confirm fit by model.

Is your dryer overheating or taking too long to dry? A damaged exhaust duct restricts airflow. This vent connector restores proper ventilation.

Dryer not heating or drying clothes properly? This cycling thermostat regulates temperature during the drying cycle. Moderate DIY repair for most models.

Replacement mounting screw for dryer panels and components. Needed when original screws are stripped, missing, or damaged during repair or maintenance.

This plate motor drives the microwave/oven turntable, keeping the glass tray rotating for even cooking and heating. Replaces a worn or failed motor to restore tray rotation and reduce uneven heating. What it does:

• Turns the glass turntable so food cooks evenly
• Stops rotation or hesitates when motor fails or wears out
• May make buzzing, grinding, or intermittent noises before failing
• Prevents the turntable from rotating if the motor no longer engages

• One replacement plate (turntable) motor

• Disconnect power before servicing to avoid shock; verify unit is fully powered off
• Remove the turntable glass and roller guide to access the motor underneath the oven/microwave floor
• Typical install requires removing interior fasteners and unplugging the motor connector; retain hardware for reassembly

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

Dryer shuts off mid-cycle or overheats? The outlet control thermistor monitors exhaust temperature. Moderately difficult repair requires drum removal.

Replace missing or stripped mounting screws in your washer dryer combo. This 12-pack secures panels, components, and internal parts during assembly or repair.

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

Fix a dryer that hums but won't start with this motor drive and pulley assembly. Powers the drum and maintains proper belt tension and alignment.

Fix a dryer that won't start, makes grinding noises, or stops mid-cycle. This motor and blower assembly restores airflow and drum rotation. Advanced repair.